CONGRATULATIONS on your decision to become the proud owner of this Plinius 9100 Integrated Amplifier. This manual has been prepared to help you understand the operation of your amplifier, and to provide information about its design and the variety of ways it may be used. We have designed and manufactured this amplifier to reproduce faithfully and accurately, your favourite music.
Introduction ...................................................................................................................................Page 3 Precautions ...................................................................................................................................Page 5 Amplifier Features – Front Panel ..................................................................................................Page 6 Amplifier Features – Rear Panel ......................................
Please take special note of the following precautions before operating your new amplifier: • The Plinius 9100 Integrated Amplifier can deliver in excess of 120 watts into 8 ohms. This amplifier is also capable of a very large peak current delivery. • The Plinius 9100 Integrated Amplifier operates in Class AB. It is capable of generating heat that could have an adverse effect on other electronic equipment, furniture, etc.
RECORD SOURCE VOLUME x x CD AUX TUNER x VCR TAPE 1 TAPE 2 6
TAPE OUTPUTS These RCA outputs are situated next to the tape RCA inputs, and are provided to interface to a pair of line level recording devices. The position of the record selector on the front panel determines from which device a recording is being made. As these tape outputs are always ‘live’, both can be used to record the chosen signal at any time. MUTE SWITCH SWITCH The mute switch enables disconnection of the output, without the need to use the remote control.
PLACEMENT PLACEMENT AND VENTILATION Your Plinius 9100 may operate at a moderately high temperature when being driven hard. The ideal location is upon a rigid stand, or floor mounted away from direct contact with any temperature sensitive materials or deep pile carpets. Ventilation through and around the amplifier should also be kept unimpeded, so ensure that the heat vents (slots in the lid and base) are not covered or restricted in any way.
It is important that you connect your loudspeakers (outputs) and source components (inputs) to the Plinius 9100 Integrated Amplifier correctly to ensure the amplifier is not damaged, and sounds its best with your system. Now that you have read and familiarised yourself with the connections on the back of the amplifier, as covered in the previous section, we will describe in detail the way in which you can connect the amplifier to your system.
BI-WIRING BI-WIRING Bi-wiring uses two pairs of loudspeaker cables for each channel loudspeaker. You will notice that the rear panel of your Plinius 9100 has two pairs of output terminals for this purpose. When using bi-wires, always connect positive (+) to positive (+) and the same for the negative (-) terminals. PHASING ((OR OR POLARITY) It is important to achieve good stereo imaging in your listening room.
REMOTE CONTROL Provided with your Plinius 9100 is a three function remote control. The two buttons at the top of the remote adjust the volume level, and the button below switches the amplifier in and out of mute. Two AAA batteries power the remote, and these are replaced by removing the two posi-drive screws on the rear face of the remote that hold the battery compartment in place. The bottom end of the remote is now free to slide down for access to the batteries.
MAINS/LINE FUSE A Mains/Line fuse is fitted within the IEC socket on the rear of the amplifier. A small drawer at the bottom of this socket may be removed (after the IEC plug is removed) by levering it out with a flat blade screwdriver. The fuse fitted should be rated at no greater than 5 amps slow blow. IMPORTANT: IMPORTANT: DO NOT FIT A FUSE WITH A HIGHER RATING.
Your Plinius 9100 Integrated Amplifier is designed for use with high fidelity loudspeakers. It should not be used to operate with any other type of appliance or equipment. Choice of loudspeakers is one of personal taste, providing the chosen loudspeakers are suitable for use with your amplifier. Be certain that your loudspeakers can handle most of the rated output power of this amplifier.
120-WATTS RMS PER CHANNEL INTO INTO 8 OHMS. BOTH CHANNELS DRI DRIVEN VEN FROM 20Hz TO 20kHz AT LESS LESS THAN 0.2% TOTAL HARMONIC DISTORTION. S FREQUENCY RESPONSE: 20Hz to 20kHz ±0.2dB. 0dB at 0Hz and -3dB at 70kHz. S DISTORTION: Typically <0.05% THD at rated power. 0.1% THD and IM worst case prior to clipping. S CURRENT OUTPUT: 20A short duration peak per channel. Fuse protected. S SLEWING: 50V/µs. S HUM & NOISE: 90dB below rated output 20Hz to 20kHz unweighted.
Bi-wiring......................................................................................................................................Page 11 Date of Manufacture .......................................................................................................................Page 3 Front Panel Layout..........................................................................................................................Page 6 Fuse Protection ....................................................
All operational, technical and descriptive material published here is subject to change at any time without notice. For further product information or queries, please contact us at the address below. PLINIUS products are designed and manufactured by: Audible Technologies Ltd. P.O. Box 1836 1836 Palmerston North New Zealand Phone: Facsimile: Email: Internet: 64 6 354 8583 64 6 354 8586 info@pliniusaudio.com www.pliniusaudio.com ©2003 Audible Technologies.