Users Manual Part 2

E-29
Networkboard(mainunit)relatederrors
ErrorDisplayNumber ProblemandSolution
Printernotcon-
nected
Noprintingpaper
Printerproblem
• Istheprintercableconnected?
• Ispowerbeingsuppliedtotheprinter?
• WhentheprinterusesanACpoweradapt-
er,isthecabledisconnectedsomewhere?
• Connect the printer properly and switch
ontheprinterpower.
• Haspaperbeensetintheprinter? • Turnthepoweroftheprinteroffandthen
onagain,andloadtheprinterwithA4or
lettersizepaper.
• Istheprintererrorindicatorflashing(orlit)? • Readtheprinterinstructionmanual.
USBMemorynot
recognized
• IstheUSBmemoryunformatted. • This unit supports the FAT and FAT 32
formats. Perform the formatting with the
personalcomputer.
• Isa USBmemorythatis not supported by
thenetworkboardbeingused?
• ThefileformatsforUSBmemorydevices
that can be used on this network board
areFATandFAT32.
• IstheUSBmemorydevicepluggedinfully? • Please check the operation with a per-
sonalcomputer.
• IstheUSBmemorydamaged? —
Memorystorage
problem
• Anerroroccurredduringmemorystorage. • Pleaseperformmemorystorageagain.
• DonotinsertorremovetheUSBmemory
duringprocessing.
Readingproblem • There is a lighting fault of the reading light
source,orareadsignalerror.
• Unplug the power plug from the power
outletandthenplugitinagain.
Systemerror • Thereisamemoryorinternalfault. • Unplug the power plug from the power
outletandthenplugitinagain.
Security protec-
tion
• The operation is set to “Disable” in the
securitysettings.
• Change the setting of the desired item
to“Enable”.(Refertotheseparate“N-31
SeriesNetworkManual”.)
Colorprinting
prohibited
• Coloringprintingissetto“Disable”. • Change the color printing setting to
“Enable”.(SeepagesE-27.)
USBmemorynot
connected
• USBmemorydeviceisnotpluggedintothe
mainunit.
• Plug the USB memory device into the
USBport.
Memoryisfull • Thereisnoavailablespace. • Please delete unnecessary data using a
personal computer. (See page E-22 and
refer to the separate “N-31 Series Net-
workManual”.)
Anunsupported
printer is con-
nected
• A printer that is not supported by the net-
workboardhasbeenconnected.
• Press the ON/Standby button and
switch off the power. When a record is
required, switch on the power and save
toUSBmemory.
Timesettingerror • An error has occurred when setting the
time.
• Start over and set the proper date and
time.
When the “USb” letter display is
flowing...Warning that disconnec-
tionofUSBmemoryhasbeenfor-
gotten
• Did you press the ON/Standby  button
whiletheUSBmemorydevicewasplugged
intothemainunit?
• A USB memory device is plugged into
the main unit. When the USB memory
device is disconnected, the power will
beswitchedoffandtheunitwillenterthe
standbymode.
Iftheproblempersists,pleasecontactyournearbyPLUSCorporationsalesoffice,dealer,orstore.
MeaningofErrorMessages
If any of the following flashing indications appear in the display window of the control
panel, please check the matters described below.
Error messages flash for 5 seconds, then stop flashing, remaining lit.