SDS

Fire fighting
equipment/instructions
In case of fire: Stop leak if safe to do so. Do not move cargo or vehicle if cargo has been exposed
to heat. Move containers from fire area if you can do so without risk. Containers should be cooled
with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose
holder or monitor nozzles, if possible. If not, withdraw and let fire burn out.
Specific methods
Use standard firefighting procedures and consider the hazards of other involved materials. Move
containers from fire area if you can do so without risk. In the event of fire and/or explosion do not
breathe fumes.
General fire hazards
Extremely flammable aerosol. Contents under pressure. Pressurized container may explode when
exposed to heat or flame.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Many gases are heavier than air and will spread along ground and collect in low or
confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing
during clean-up. Do not breathe mist or vapor. Emergency personnel need self-contained
breathing equipment. Do not touch damaged containers or spilled material unless wearing
appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities
should be advised if significant spillages cannot be contained. For personal protection, see section
8 of the SDS.
Methods and materials for
containment and cleaning up
Refer to attached safety data sheets and/or instructions for use. Eliminate all ignition sources (no
smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.)
away from spilled material. Stop leak if you can do so without risk. Move the cylinder to a safe and
open area if the leak is irreparable. Isolate area until gas has dispersed. Cover with plastic sheet to
prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Prevent
product from entering drains. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination. For waste disposal, see section 13 of the SDS.
Environmental precautions
Avoid release to the environment. Prevent further leakage or spillage if safe to do so. Avoid
discharge into drains, water courses or onto the ground. Inform appropriate managerial or
supervisory personnel of all environmental releases.
7. Handling and storage
Precautions for safe handling
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spray
button is missing or defective. Do not spray on a naked flame or any other incandescent material.
Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill,
grind, or expose containers to heat, flame, sparks, or other sources of ignition. All equipment used
when handling the product must be grounded. Do not re-use empty containers. Do not breathe
mist or vapor. Avoid contact with eyes. Avoid prolonged exposure. When using, do not eat, drink or
smoke. Pregnant or breastfeeding women must not handle this product. Should be handled in
closed systems, if possible. Use only in well-ventilated areas. Wear appropriate personal
protective equipment. Wash hands thoroughly after handling. Avoid release to the environment.
Observe good industrial hygiene practices.
Conditions for safe storage,
including any incompatibilities
Level 2 Aerosol.
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Secure cylinders in an upright position at all times,
close all valves when not in use. Store in a well-ventilated place. Store away from incompatible
materials (see Section 10 of the SDS).
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents
Form
Type
PEL 2400 mg/m3ACETONE (CAS 67-64-1)
1000 ppm
PEL 1400 mg/m3ETHYL ACETATE (CAS
141-78-6)
400 ppm
PEL 435 mg/m3ETHYLBENZENE (CAS
100-41-4)
100 ppm
3 / 14
M
aterial name: HOT SAUCE 30120US
07844 101772 604 Version #: 01 Issue date: 04-24-2015
SDS US