User Manual PLX devices inc. Patents Pending © PLX Devices Inc.
Contents 1 Introduction 2 Overview 3 Operating Legion 4 Product Care and Maintenance 5 Troubleshooting 6 Technical Specifications Patents Warnings Key Features Package Contents 3 3 3 3 Accessories Intelligent OLED Display 4 5 Charging Your Devices Charging Your Legion Toggling Menus About Legion Menus Sleep Mode Turning Your Legion ON and OFF 6 6 7 7 7 8 Storage Battery Use and Safety Disposal 9 9 10 Resetting Legion Problem Charging Your Device Problem Charging Your Legion Problem Turni
1 Introduction Patents PLX Devices Inc. currently has patents pending on the intelligent battery metering hardware, firmware, and algorithms. Warnings Each Legion contains a Lithium Polymer (LiPo) battery. LiPo batteries are volatile. Improper handling of LiPo batteries can result in fire. Read ALL instructions before use. Do not use this product and its accessories in any way other than specified by PLX Devices Inc. PLX Devices Inc. is not liable for accidents or damage caused by misuse of this product.
2 Overview Accessories Included Accessories Charging Cable Additional accessories that may be purchased at www.plxdevices.com Large and Small Carrying Case 6-In-1 Charging Cable PLX devices inc. www.plxdevices.
Intelligent OLED Display Shows the percent charge remaining and the actual capacity remaining in mAh. Shows the amount of time (days:hours:minutes) remaining until Legion becomes empty. Shows the amount of time (days:hours:minutes) remaining until Legion becomes fully charged. Shows the health of your battery. Legion keeps track of your battery’s wear and tear. Shows the number of charge cycles, battery age, and battery temperature. Shows the battery’s voltage.
3 Operating Legion Charging Your Device 1. Connect the Micro USB end of the Retractable Cable into the port of the device you want to charge. NOTE: The provided Retractable Cable is intended to only be used with devices that contain Micro USB ports. Devices with a different type of port will require their appropriate cable. 2. Insert the USB Male A end of the Retractable Cable into Legion’s USB Charge Out Port. NOTE: Connecting the cable improperly may cause serious damages to the device.
Toggling Menus To toggle through the menus, press and release the button located to the right of the Organic LED Display. About Legion Menus Four different menus may be displayed on Legion’s Organic LED Display. These menus include Time Remaining, Battery Percentage, Electrical, and Health. Time Remaining When the Time Remaining menu is selected, either the Time to Discharge or the Time to Charge will be displayed.
Turning Your Legion ON and OFF 1. To turn your device ON for the first time, connect the provided jumper into the device. To turn the device ON from OFF, press and hold the button for a few seconds until the Organic LED Display turns on. NOTE: The jumper must be installed in order for Legion to be operable. 2. To turn your device OFF, press and hold the button for a few seconds until the Organic LED Display turns off.
4 Product Care and Maintenence Your mobile battery device is a product of superior design and should be treated with care. The guidelines below will allow you to enjoy this product for years to come. Storage Legion should be stored at room temperature in cool or shaded areas, ideally between 10°C (50°F) to 25°C (77°F). For long term storage (over 3 months), the voltage should ideally rest between 3.6 V to 3.9 V.
process immediately. Batteries that exceed 60 °C (140°F) during charge or discharge can and usually will become damaged and possibly catch on fire. Place the product in a safe, open area away from flammable materials for at least 15 minutes. Continuing to charge or discharge a battery that has begun to swell or smoke can result in fire. A battery that has ballooned or swollen must be removed from service immediately.
5 Troubleshooting Resetting Legion If Legion has an error or freezes, you may need to reset Legion to regain functionality. Quick Reset For a quick product reset, unplug and replug the jumper from the jumper port. This will restart the product and retain any ongoing data (such as remaining capacity of the battery and charge cycles). Factory Setting Reset To reset the product to its factory setting: 1. Remove the jumper from the jumper port. 2.
4. If your device is still not being charged and Legion is ON, unplug and replug the jumper to perform a quick reset. 5. If your device still does not charge after going through Steps 1 – 4 , visit www.plxdevices.com, and contact us to speak to a support technician who can further assist you. Problem Charging Your Legion If you are unable to charge Legion: 1. Check to see if the charging cable is working properly by using the same charging cable to charge another device, using the same power source.
6 Technical Specifications Patents Pending Legion 5500mAh Battery Charge Output Charge Input Display Human Interface Operating Temperature Storage Temperature Physical Dimensions Weight Enclosure Intellectual Properties Power Supply Lithium Polymer 5500mAh USB Female A 5.0V Single 1A (5500mAh) Micro USB 5.0V High Contrast OLED 128 x 32 Pixels 1 Push Button 0 – 45 Deg Celsius -10 – 45 Deg Celsius 2.43 x 4.32 x 0.52” (6.17 x 10.97 x 1.33cm) 4.
TERMS OF USE – PLX Devices Inc. does not guarantee product functionality with any third party device. Implementation and integration of the PLX products with any other device(s) must be done at your own risk. LIMITED WARRANTY – PLX Devices Inc. warrants this product to be free from defects for 1 year from the date of purchase. If applicable, non-serviceable items are excluded from stated warranty.