Instructions / Assembly

FIG. 1 FIG. 2
FIG. 3
FIG. 4
FIG. 5 FIG. 6
Board and Batten Installation Instructions
1. Remove shutters from the carton and remove one side of the Batten Caps as
Shown in Fig. 1 and Fig. 2 with a blunt object such as the shank end of a 1/8” drill bit.
Note: If installing with exposed fasteners (shutter plugs); skip step 1 & 2.
2. Once caps are removed from one side, slide the Batten Boards off the shutter
assembly and place in a safe area with the caps that have been removed.
4. Once shutters are installed reattach batten board by sliding them over the rail in
reverse of step #2. Fig. 5
5. Gently reinstall batten board caps by sliding them into the end of the batten
boards. Caps should be flush and securely fasten to the batten board by the snaps.
PRESS DOWN GENTLY TO
DISENGAGE CAP SNAP.
REMOVE CAPS ON
ALL BATTENS. ONE
SIDE ONLY.
ONCE CAPS ARE REMOVED,
SLIDE BATTENS OFF THE SHUTTER.
ONCE THE SHUTTER IS INSTALLED, SLIDE THE
BATTEN BOARDS OVER THE ATTACHED RAILS.
Four Board Closed
Board and Batten
Four Board Open
Board and Batten
Three Board Closed
Board and Batten
Three Board Open
Board and Batten
POSITION SHUTTER AND INSTALL FASTENERS SUPPLIED
(& PLACES OVER 51 INCHES).
NOTE: WHEN INSTALLING THE "ARCH TOP BOARD & BATTEN
SHUTTER" PLACE THE SCREWS IN THE TOP HALF OF THE TOP
RAIL, NOT IN THE CENTER. THIS WILL PROVIDE ADDED
SUPPORT FOR THE ARCH.
GENTLY INSERT AND SNAP
THE BATTEN CAPS TO THE
BATTEN BOARDS TO ATTACH
AND FINISH.
FIG. 1 FIG. 2
FIG. 3
FIG. 4
FIG. 5 FIG. 6
Board and Batten Installation Instructions
1. Remove shutters from the carton and remove one side of the Batten Caps as
Shown in Fig. 1 and Fig. 2 with a blunt object such as the shank end of a 1/8” drill bit.
Note: If installing with exposed fasteners (shutter plugs); skip step 1 & 2.
2. Once caps are removed from one side, slide the Batten Boards off the shutter
assembly and place in a safe area with the caps that have been removed.
4. Once shutters are installed reattach batten board by sliding them over the rail in
reverse of step #2. Fig. 5
5. Gently reinstall batten board caps by sliding them into the end of the batten
boards. Caps should be flush and securely fasten to the batten board by the snaps.
PRESS DOWN GENTLY TO
DISENGAGE CAP SNAP.
REMOVE CAPS ON
ALL BATTENS. ONE
SIDE ONLY.
ONCE CAPS ARE REMOVED,
SLIDE BATTENS OFF THE SHUTTER.
ONCE THE SHUTTER IS INSTALLED, SLIDE THE
BATTEN BOARDS OVER THE ATTACHED RAILS.
Four Board Closed
Board and Batten
Four Board Open
Board and Batten
Three Board Closed
Board and Batten
Three Board Open
Board and Batten
POSITION SHUTTER AND INSTALL FASTENERS SUPPLIED
(& PLACES OVER 51 INCHES).
NOTE: WHEN INSTALLING THE "ARCH TOP BOARD & BATTEN
SHUTTER" PLACE THE SCREWS IN THE TOP HALF OF THE TOP
RAIL, NOT IN THE CENTER. THIS WILL PROVIDE ADDED
SUPPORT FOR THE ARCH.
GENTLY INSERT AND SNAP
THE BATTEN CAPS TO THE
BATTEN BOARDS TO ATTACH
AND FINISH.
FIG. 1 FIG. 2
FIG. 3
FIG. 4
FIG. 5 FIG. 6
Board and Batten Installation Instructions
1. Remove shutters from the carton and remove one side of the Batten Caps as
Shown in Fig. 1 and Fig. 2 with a blunt object such as the shank end of a 1/8” drill bit.
Note: If installing with exposed fasteners (shutter plugs); skip step 1 & 2.
2. Once caps are removed from one side, slide the Batten Boards off the shutter
assembly and place in a safe area with the caps that have been removed.
4. Once shutters are installed reattach batten board by sliding them over the rail in
reverse of step #2. Fig. 5
5. Gently reinstall batten board caps by sliding them into the end of the batten
boards. Caps should be flush and securely fasten to the batten board by the snaps.
PRESS DOWN GENTLY TO
DISENGAGE CAP SNAP.
REMOVE CAPS ON
ALL BATTENS. ONE
SIDE ONLY.
ONCE CAPS ARE REMOVED,
SLIDE BATTENS OFF THE SHUTTER.
ONCE THE SHUTTER IS INSTALLED, SLIDE THE
BATTEN BOARDS OVER THE ATTACHED RAILS.
Four Board Closed
Board and Batten
Four Board Open
Board and Batten
Three Board Closed
Board and Batten
Three Board Open
Board and Batten
POSITION SHUTTER AND INSTALL FASTENERS SUPPLIED
(& PLACES OVER 51 INCHES).
NOTE: WHEN INSTALLING THE "ARCH TOP BOARD & BATTEN
SHUTTER" PLACE THE SCREWS IN THE TOP HALF OF THE TOP
RAIL, NOT IN THE CENTER. THIS WILL PROVIDE ADDED
SUPPORT FOR THE ARCH.
GENTLY INSERT AND SNAP
THE BATTEN CAPS TO THE
BATTEN BOARDS TO ATTACH
AND FINISH.
FIG. 1 FIG. 2
FIG. 3
FIG. 4
FIG. 5 FIG. 6
Board and Batten Installation Instructions
1. Remove shutters from the carton and remove one side of the Batten Caps as
Shown in Fig. 1 and Fig. 2 with a blunt object such as the shank end of a 1/8” drill bit.
Note: If installing with exposed fasteners (shutter plugs); skip step 1 & 2.
2. Once caps are removed from one side, slide the Batten Boards off the shutter
assembly and place in a safe area with the caps that have been removed.
4. Once shutters are installed reattach batten board by sliding them over the rail in
reverse of step #2. Fig. 5
5. Gently reinstall batten board caps by sliding them into the end of the batten
boards. Caps should be flush and securely fasten to the batten board by the snaps.
PRESS DOWN GENTLY TO
DISENGAGE CAP SNAP.
REMOVE CAPS ON
ALL BATTENS. ONE
SIDE ONLY.
ONCE CAPS ARE REMOVED,
SLIDE BATTENS OFF THE SHUTTER.
ONCE THE SHUTTER IS INSTALLED, SLIDE THE
BATTEN BOARDS OVER THE ATTACHED RAILS.
Four Board Closed
Board and Batten
Four Board Open
Board and Batten
Three Board Closed
Board and Batten
Three Board Open
Board and Batten
POSITION SHUTTER AND INSTALL FASTENERS SUPPLIED
(& PLACES OVER 51 INCHES).
NOTE: WHEN INSTALLING THE "ARCH TOP BOARD & BATTEN
SHUTTER" PLACE THE SCREWS IN THE TOP HALF OF THE TOP
RAIL, NOT IN THE CENTER. THIS WILL PROVIDE ADDED
SUPPORT FOR THE ARCH.
GENTLY INSERT AND SNAP
THE BATTEN CAPS TO THE
BATTEN BOARDS TO ATTACH
AND FINISH.
Installation Instructions for
Ply Gem Board and Batten Shutters
1. Remove shutters from the carton and remove one side of the
Batten Caps as Shown in Fig. 1 and Fig. 2 with a blunt object
such as the shank end of a 1/8” drill bit. Note: If installing
with exposed fasteners (shutter plugs); skip step 1 & 2.
PRESS DOWN
GENTLY TO
DISENGAGE
CAP SNAP.
FIG 1
REMOVE CAPS ON ALL
BATTENS. ONE SIDE ONLY.
FIG 2
ONCE CAPS ARE
REMOVED, SLIDE
BATTENS OFF
THE SHUTTER.
2. Once caps are removed from one side, slide the Batten
Boards o the shutter assembly and place in a safe area
with the caps that have been removed.
FIG 3
POSITION SHUTTER AND
INSTALL FASTENERS SUPPLIED
(& PLACES OVER 51 INCHES).
NOTE: WHEN INSTALLING THE
“ARCH TOP BOARD & BATTEN
SHUTTER” PLACE THE SCREWS
IN THE TOP HALF OF THE TOP
RAIL, NOT IN THE CENTER.
THIS WILL PROVIDE ADDED
SUPPORT FOR THE ARCH.
3. Position shutter in desired location and drill a 7/32” diameter
hole through shutter only and spot mark this location on the
wall. Remove the shutter and drill a 3/32” diameter pilot hole
on each location and then fasten the shutter with supplied
metal screws as shown in Fig. 4. (6) Screws are required for
shutters over 51” in length. (4) Screws for shutters up to 51”
Note: As an optional attachment method the plastic plugs
can be installed as an exposed fastener into the rails only. If
installing shutters over vinyl siding drill a hole ¼” larger (into
the siding only) than the diameter of the fastener (metal
screw or plastic plug)
FIG 4
ONCE THE SHUTTER IS
INSTALLED, SLIDE THE
BATTEN BOARDS OVER
THE ATTACHED RAILS.
4. Once shutters are installed reattach batten board by sliding
them over the rail in reverse of step #2. Fig. 5
FIG 5
GENTLY INSERT AND
SNAP THE BATTEN
CAPS TO THE BATTEN
BOARDS TO ATTACH
AND FINISH.
5. Gently reinstall batten board caps by sliding them into the
end of the batten boards. Caps should be flush and securely
fasten to the batten board by the snaps.
FIG 6
MS/0519
RECOMMENDED TOOLS & ACCESSORIES:
• Power Drill • Phillips Head Bit or Screwdriver • Safety Glasses
• Gloves