User's Manual

TROUBLESHOOTING
WARRANTY
27 28
may vary from state to state.
KEE is not liable for any consequential damages or incidental damages which may arise from the use or
operation of the Piranha
®
or from any breach of the warranty herein set forth.
WARRANTY REGISTRATION FORM
Please fill out entirely the enclosed Piranha
®
Registration form and mail it to: KEE Action Sports, 570 Mantua
Blvd., Sewell, NJ 08080 USA.
The Piranha
®
is a registered trademark. Design rights & all rights reserved. All patterns, drawings, photo-
graphs, instructions or manuals remain the intellectual property of the manufacturer. Patents
pending. All rights will be strictly enforced.
The Piranha
®
GTI Plus is capable of high rates of fire and an agitating hopper such as
an Extreme Rage
®
Overdrive
™
is recommended for better performance.
Cocking Rod
Velocity
Adjustment
Screw
Safety Slide
Sear Release
Gas Thru Grip
PMI High Performance Barrel
Bottomline Adapter
Dual Ball Detents
OPERATING THE PIRANHA
®
GTI PLUS: 1. Attach threaded
barrel firmly to marker. 2. At this time, do not attach air source or loader
and do not load paintballs into marker. 3. Insert barrel plug firmly into bar-
rel. 4. Pull the cocking knob straight back from the rear of the marker until
the cocking mechanism locks back in the cocked position. Always cock mark-
er before airing it up. During cocking the flush cocking rod will recoil or
“spring back” into the marker once released and will only move slightly dur-
ing marker operation. 5. Slide safety “off,” 6. Squeeze the trigger with an
even pressure. You should hear the hammer and bolt assembly slide forward.
7. Cock the marker. 8. Before attaching the air source, read and understand
the section in the manual on “Compressed Gas/Air.” Follow safety rules for
handling compressed gas/air. If any leak occurs in the marker, refer to trou-
bleshooting guide or to a qualified airsmith. Use only cylinders for com-
pressed gas or air that comply with all applicable laws and regulations,
including but not limited to those of the U.S. Department of Transportation,
OSHA, Compressed Gas Association, and/or American Society for Testing and
Materials. 9. With goggles on, test for function after attaching air source:
Squeeze the trigger. The marker should shoot air and the cocking knob
should cycle slightly after each trigger squeeze, repeat several times. Flush
cocking rods will bobble some, but they will not come out all the way.
10. Slide safety forward (semi version). Paintballs may then be loaded.
1A. Milled Receiver Body - Matte Black 73100
1B. Milled Receiver Body - Matte Blue 73101
1C. Milled Receiver Body - Matte Gunmetal 73102
2. 9” Barrel 73120
3. End Cap GTI 73123
5. Field Strip Pin Assembly 10038
6. Valve Body 10027
7. Red Valve Cup Seal Assembly 10140
7. Black Valve Cup Seal Assembly 10127
8A. Removable Low Rise - Matte Black 73110
8B. Removable Low Rise - Matte Blue 73111
8C. Removable Low Rise - Matte Gunmetal 73112
9. Valve Guide 10520
10. Valve Spring 71597
11. Molded Flush Cocking Bolt 73124
12. Molded Flush Cocking Rear Block Assembly 73127
13. Molded Flush Cocking Rod 73126
14. Hammer Assembly 10024
15. Blue Hammer Spring 10351
16. ASA O-ring 10257
17. Spring Guide 10301
18A. Vertical ASA Adapter - Matte Black 73105
18B. Vertical ASA Adapter - Matte Blue 73106
18C. Vertical ASA Adapter - Matte Gunmetal 73107
19L. Ball Detent Cap Left 73129
19R. Ball Detent Cap Right 73130
20. Ball Detent 10160
21. Polymer Frame Assembly ‘07 73140
22. Sear Release Slide 73144
23. Wrap Around Grip 73145
25. Velocity Screw 10026
26. Valve Set Screw 10513
27. ASA Screw 71580
28. Ball Detent Screw 10180
29. Rear Trigger Frame Screw 10682
29A. Front Trigger Frame Screw 71583
30. Grip Screws 10782
32. Bolt Pin 10291
33. Velocity Screw O-Ring 10460
34. Valve/Rear Block O-Rings 10260
35. Blue Hammer O-Ring 10129
36. Screen Filter 71667
37. Bolt O-Rings 41010
37A. Gas Thru Grip O-Ring 41010
37B. ASA Slug O-Ring 41010
38A. Trigger 73141
38B. Trigger Pawl Assembly 73142
39. Barrel O-Ring 10161
40. Gas-Thru Foregrip 73121
41. 6.25" SS hose 47011
42. Bottom line SS screw 42016
43. Straight Bottomline Adapter 73122
44. Sear 10721
45. 90° Elbows 47000
46. Safety Slide 73143
47. Safety Ball 10730
48. Safety Spring 10750
53. Flush Spring 10203
55. Trigger Spring 73146
56 Sear/Trigger Pin 10766
57. Trigger/Spring Pin 10767
58. Sear Spring 10753
59. Front Bolt O-Ring 57738
67. 1/8th” NPT Plug 47006
Manual_Piranha_5.5_eng.qxd 11/16/07 1:58 PM Page 20