Use and Care Manual

ManualsBrandsPMI ManualsAir Conditioners & CoolersWater Conservation Evaporative Cooler, Cools up to 1000 sq. ft., 1/3-HP 2-Speed Motor; High Efficiency Rigid Media

WINDOW COOLER MODEL

OWNER’S GUIDE

USE AND CARE MANUAL

1-999-2542 Date: 03/16

Safety

Installation

Start-up

Operation

Maintenance

Troubleshooting

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING.

 Read all instructions carefully before installation.

 This cooler must be connected to 120 Volt AC, 60 Hz (cycle)

power only. NOTE: Improper voltage will void the pump and/or

motor warranties and may cause serious personal injury or

property damage.

 This cooler must be plugged into a GFCI protected receptacle,

which has been properly installed in accordance with all local

and national codes. If you are not sure that the receptacle is

GFCI protected, consult with a qualified electrician.

 This cooler is equipped with a power cord having an equipment

grounding conductor and grounding plug. Do not attempt to

defeat this safety device by removing the grounding pin.

 Use of an extension cord is not recommended.

 Do not operate if plug or cord is damaged in any way. If the unit

is damaged or malfunctions, do not continue to operate it.

 Always disconnect electrical power to unit before attempting to

work on or service your cooler.

 Some models may have a restricting orifice in the pump water

tube to assure proper water flow rate to the pad. Do not remove

this restrictor!

 Remove the plug from the electrical receptacle by pulling on

the plug and not the cord.

 Do not operate this blower (fan) motor with any solid-state

speed control device.

 Do not operate this unit with pad frame(s) and/or air outlet grille

removed, this may cause the fan motor to overload and

damage the motor.

NOTE:

 Do not locate unit near exhaust or vent pipes as odors or fumes

may be drawn into cooler.

 Use of anode devices, chemical additives or treatments in this

cooler will void the warranty.

 Your warranty does not cover shipping damage. Report all

shipping damage at once to dealer or carrier making the delivery.

 For future reference, record the model and serial numbers, date

and place of purchase of your evaporative cooler here:

Model #

Serial #

Date of Purchase:

Place of Purchase:

Congratulations: You have purchased a product of superior performance and design,

which will give the best service when properly installed, operated and maintained.

This guide will provide you with information needed to mount, operate, inspect, maintain,

and troubleshoot your Aerocool water conservation window cooler.

The first section, Installation and Start-Up, gives details for installation. The second

section, Maintenance, contains operational and maintenance instructions, while

Troubleshooting includes information on commonly encountered problems.

INSTALLER: Please deliver this guide to owner.

Model: WCBW4000

Water Conservation Cooler

PHOENIX MANUFACTURING, INC.

Summary of content (12 pages)

PAGE 1
PHOENIX MANUFACTURING, INC. OWNER’S GUIDE USE AND CARE MANUAL WINDOW COOLER MODEL Safety Installation Start-up Operation Maintenance Troubleshooting Model: WCBW4000 Water Conservation Cooler Congratulations: You have purchased a product of superior performance and design, which will give the best service when properly installed, operated and maintained.
PAGE 2
INTRODUCTION Your Aerocool evaporative air cooler was thoroughly tested and inspected before leaving the factory. This manual is your guide to proper installation procedures along with information about reasonable care and maintenance that will ensure safe, economical and trouble free cooling. Failure to follow these instructions may damage your cooler, impair its operation, create the potential for serious personal injury and/or void the warranty. Read it carefully.
PAGE 3
Mounting Using Chain Kit Install Overflow Standpipe / Drain Line An alternate installation method involves locating the unit in a suitable window and using the included chain mounting kit to support the weight of the cooler. As with platform or stand mounting, every installation will be different. The exact requirements to mount and seal a cooler against the weather will be best determined by the location and at the time of the installation.
PAGE 4
GENERAL INSPECTION Initial Start-up or Annual Inspection CAUTION: Disconnect all electrical power to the cooler before attempting to install, open, or service your cooler. Before start-up of the cooler for the first time, or at the beginning of each cooling season, make sure that all required connections, adjustments, etc. have been made. Verify that: P Cooler mounting is level; window and duct are sealed. P Power supply cord is correctly routed, safe and secure.
PAGE 5
Cleaning Water Pump & Hose CAUTION: Disconnect all electrical power to the cooler Blower Shaft Bearings CAUTION: Do not allow pump to fall over and become submerged; water will damage pump motor. Blower shaft bearings need periodic lubrication. They should be checked 20-30 days after initial start-up of operation. The oil cups on the bearings should be filled with a good grade of SAE 20W or 30W non-detergent oil when necessary. Under normal use, oiling is required every three months of operation.
PAGE 6
TROUBLESHOOTING GUIDE: Should an obvious problem occur with your cooler consult the following table. If you cannot correct the problem, or if it persists, contact qualified service personnel.
PAGE 7
TRAZANDO FALLAS : Si un problema obvio ocurre en su enfriador, consulte la siguiente tabla. Si no puede corregir el problema, contacte a un representante competente de servicio.
PAGE 8
Limpieza de la bomba y manguera PRECAUCION: Desconecte toda la corriente eléctrica del enfriador antes de intentar instalar, abrir, o darle servicio a su enfriador. PRECAUCION: No permita que la bomba se caiga y se sumerja; el agua daña el motor. Limpie la bomba, bomba le dren, la manguera y la ensamble de distribuidor como sigue: Desenchufe el cordón clavija de la bomba, remueva el tornillo de la abrazadera de la bomba y remueva la bomba del enfriador. Sacúdala ligeramente para removerla del agua.
PAGE 9
INSPECCIÓN GENERAL Lista de inspección de pre-comienzo o anual PRECAUCION: Desconecte toda la corriente eléctrica del enfriador antes de intentar instalar, abrir, o darle servicio a su enfriador. Antes de prender el motor y la bomba por primera vez, o en el comienzo de cada temporada de enfriamiento, asegúrese de haber hecho todas las conexiones y ajustes. Y verifique que: P Montura del enfriador a nivel; ventana y ductos sellados. P El cordón clavija este correctamente guiado, seguros y fuera de peligro.
PAGE 10
Montado Usado Juego de Cadena La instalación alternativa envuelve el situar la unidad en una ventana apropiada y usando el juego de cadena inclido para que soporte el peso del enfriador. Asi como montado en plataforma o tarima, cada instalación es diferente. Los requerimientos exactos para montar y sellar el enfriador en contra del clima será determinado por el sitio y al momento de la instalación.
PAGE 11
INTRODUCCIÓN Su enfriador fue detalladamente probado e inspeccionado antes de salir de la fábrica. Ester manual es una guía de procedimientos para una instalación propia junto con información de un cuidado razonable y mantenimiento que le asegurará un enfriamiento seguro, económico y sin problemas. El no seguir estas instrucciones puede dañar su enfriador, incapacitar su operación, crear un potencial para una seria lastimadura personal y/o anular la garantía.
PAGE 12
PHOENIX MANUFACTURING, INC. GUÍ A DEL PROPIETARO MANUAL DE USO Y CUIDADO ENFRIADOR EVAPORATIVO de VENTANA Seguridad Instalación Incio Operación Mantenimiento Trazando Fallas Model: WCBW4000 Conservación del Agua Enfriador Evaporativo Felicitaciones: Usted acaba de comprar un producto de superior rendimiento y diseño, que la dará el mejor servicio cuando sea propiamente instalado, operado y mantenido.