Instruction Manual HIGH IMPEDANCE PASSIVE PROBE PMS201A-RO
Copyright © 2005 PMK GmbH All rights reserved. Information in this publication supersedes that in all previously published material. Specifications are subject to change without notice. Manufacturer PMK GmbH Mess- und Kommunikationstechnik Industriestr. 17 63150 Heusenstamm, Germany Phone: Fax: +49 (0) 6104 6453 +49 (0) 6104 6457 Internet: www.pmk-gmbh.com E-Mail: sales@pmk-gmbh.com service@pmk-gmbh.
PMS201A Declaration of Conformity (EC conformity marking) The manufacturer declares the conformity of this product with the actual required safety standards in accordance with the Low Voltage Directive (LVD) 73/23/EEC and amendment 93/68/EEC: CEI/IEC 61010-031:2002 Safety requirements for electrical equipment for measurement, control and laboratory use Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test WEEE/ RoHS Directives (EC conformity marking) This el
IEC Measurement Categories Measurement Category I Measurement Category II Definitions and Examples (Clause 6.5.2 ) Definition: Measurement category I is for measurements performed on circuits not directly connected to a mains supply. Examples: Measurements in circuits not derived from a mains supply and specially protected ( internal ) circuits derived from a mains supply.
Safety Information PMS201A To avoid personal injury and to prevent fire or damage to this product or products connected to it, review and comply with the following safety precautions. Be aware that if you use this probe assembly in a manner not specified the protection this product provides may be impaired. Only qualified personnel should use this probe assembly. Use only grounded instruments. Do not connect the probe ground lead to a potential other than earth ground.
PMS201A Specifications Specifications that are not defined to be guaranteed are typical and are published as general information to the user. The instrument should have warmed-up for at least 20 minutes and the environmental conditions do not exceed the probe `s specified limits.
Handling PMS201A Handle with care especially when fitted with the extra thin and sharp spring contact tip to avoid any injury. Note that the probe cable is a sensitive part of the probe. Do not damage through excessive bending or pulling. Avoid mechanical shock to this product in general to guarantee accurate performance and protection. Maintenance Cleaning To clean the exterior of the probe use a soft cloth moistened with either distillated water or isopropyl alcohol.
PMS201A Probe Accessory 3 -06 92 5.0 ay r 8-2 01 -Cap ch; g t C i I p mm 8 0. 4 -06 92 5.0 wn 8-2 01 -Cap h; bro C c I pit mm 1.0 972405100 Safety Alligator Clip black 5 -06 92 5.0 ack l 8-2 01 -Cap ch; b t C i I p mm 7 1.2 7 -01 ap 92 8-2 g C 01 latin k u c Ins bla 7 -02 .0 92 p 5 8-2 Ca 01 tion k c c te bla Pro 890-220-000 Flexible Adapter 5.0 to 4 mm safety banana plug 890-320-000 Sprung Hook II 5.0 black 1 -00 0 10 ter 5. 8-2 01 Adap C BN 0 -00 0 00 ter 5.
PMS201A Probe Accessory 6 -00 l 92 Too 8-2 nt 01 stme u j Ad 4 -02 l 92 Too 8-2 nt 01 stme ju EIN Ad ST 2 -91 ings 10 0-0 g R 89 odin lors o C c Set 3x4 RN BE 893-250-001 2 Footer Positioner 891-005-011 5x Solid Tip 0.8 mm 891-005-803 5x Spring Tip 0.
PMS201A Scope of delivery The following items are included in the scope of delivery. Please check the delivery for completeness. If any item is missing, send a message to our service department and we will send you this item immediately. Item Ground Blade 5.0 Ground Lead 22 cm IC-Cap 5.0 0.8 mm pitch; grey IC-Cap 5.0 1.0 mm pitch; brown IC-Cap 5.0 1.27 mm pitch; black Instruction Manual Insulating Cap PMS Probe Protection Cap 5.0 self adhesive Cu Pads (2 x 2 cm) Solid Tip 0.8 mm Spring Tip 0.
PMS201A This page is reserved.
PMS201A M20-201-A01 12 Revision A - January 2006
