PREFACE Thank you for purchasing P15UV Two Way Radio, It is a multitask GMRS transceiver. Combining the latest technology in radio communication along with a sturdy mechanical frame, P15UV is the ideal and effective solution for the professionals who need to stay in touch with the working team (in construction sites, buildings, shows, trade fairs or hotels) or for leisure users that just want to keep up with friends and family.
Table of Contents 1. GETTING STARTED 1.1 Regulations and Safety Warnings 1.2 Content of the packaging 1.3 Main features 1.4 Maintenance 2. BATTERY INFORMATION 2.1 Charging the Battery Pack 2.2 Charger Supplied 2.3 Use Caution with the Li-ion Battery 2.4 How to Charge 2.5 LED Indicator 2.6 How to Store the Battery 2.7 Using the Type-C USB Charger 3. INSTALLATION OF ACCESSORIES 3.1 Installing / Removing the Antenna 3.2 Installing the belt clip 3.3 Installing the battery pack 3.
5.1 Power on the radio 5.2 Adjusting the volume 5.3 Channel selection 5.4 Making a call 5.5 Frequency (VFO) mode 5.6 Channel (MR) mode 6. ADVANCED FEATURES 6.1 Frequency scanning 6.2 Channel scanning 6.3 CTCSS scanning 6.4 DCS scanning 6.5 Cursor Conversion (A/B) 6.7 Keypad lock 6.8 FM Radio (FM) 6.9 TX 1000Hz, 1450Hz, 1750Hz, 2100Hz repeaters tone 6.10 Manual Programming (Channels Memory) 6.11 Built-in LED Flashlight 6.12 NOAA weather Receiver /Scan 7. WORKING THE MENU SYSTEM 7.1 Basic use 7.
1. GETTING STARTED 1.1 Regulations and Safety Warnings ■ FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Our radio generators RF electromagnetic energy during transmit mode. This radio is designed for and classified as“General Population”,meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways To Minimize Such hazards.
Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Attention: This radio complies with IEEE and ICNIRP exposure limits for General Population/Uncontrolled Environments RF exposure environment at operating duty factors of up to 50% and is authorized by the FCC for Occupational use only.
• Never open your radio’s case. • Never change or replace anything in your radio except the battery. • Any attempt to change frequencies or output power of the radio invalidates the approval RF Exposure Information WARNING! Read this information before using the radio.
license. Because this radio operates in the 0.5 to 5 watt GMRS power range all GMRS rules apply and will require you have a GMRS license even for 8-14ch communication. Normal 8-14th only radios operate at a maximum power of 0.5 watt (500 mill watt) power and have an integral (non-detachable) antenna.
1.2 Content of the packaging • 1 P15UV transceiver • 1 Fast desktop charger • 1 Belt clip If any item is missing, please verify with your dealer. •1 •1 Li-Ion battery pack 1500mAh 7.4V Wall adaptor 1.
About Range Your P15UV Series radios are designed to give you maximum range under optimum conditions. • Maximum Range: Little to No sight Obstruction. • Medium Range: Partial Obstruction to line of sight. • Short Range: Major Obstruction to Ling of Sight.
• If it appears that the Radio diffuses peculiar smell or smoke, please shut off its power immediately and take off the charger or battery from the radio. • Do not transmit without antenna. 2. BATTERY INFORMATION 2.1 Charging the Battery Pack The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity.
f. Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage. WARNING！ When keys, ornamental chain or other electric metals contact the battery terminal, the battery may become damage or injure a human. If the battery terminals are short circuited it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container. 2.4 How to Charge a.
2.6 How to Store the Battery a. If the battery needs to be stored, keep it in status of 80% discharged. b. It should be kept in low temperature and dry environment. c. Keep it away from hot places and direct sunlight. » Do not short circuit the battery terminals. » Never attempt to remove the casing from the battery pack. » Never store the battery in unsafe surroundings, as a short may cause an explosion. » Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
3. INSTALLATION OF ACCESSORIES Before the radio is ready for use we need to attach the battery pack, as well as charge the battery. 3.1 Installing the belt clip a. At the back of the radio there are two parallel screws mounted above the battery, remove these and thread them through the holes on the belt clip as you screw them back into the radio body. b. Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip. 3.
4.
1. Antenna 2. Power Switch / Volume control: Rotate to switch on/off the radio and adjust the volume 3. Speaker 4. Microphone 5. LCD display 6. (MENU) key: enter the MENU functions and confirms the selection. In standby mode, press and hold the key to switch between frequency mode an MENU d channel mode. Press and hold down the MENU key to switch between the frequency mode and channel mode. 7. Alphanumerical keypad. 8. / (Back/WX) key: press to exit the Menu and functions.
4.2 Main controls and parts of the radio LCD Display 1. Received signal strength. 2. power. 3. Appears when DTMFST (DT-ST / DT + ANI / ANI-ST) is activated. 4. These symbols show that you set a DCS or CTCSS code in tx or rx. In tx mode it appears while you are transmitting, while in rx mode it is shown also in stand-by condition. 5. Appears when a positive shift is activated. 6. Appears when a negative shift is enabled. 7. This letter is displayed when the Dual Watch function is active. 8.
13/17. Depending on the setting, it will show the frequency in use, the channel name, the menu setting, etc 14/15. Indicates the VFO in use and the current menu or function setting. This icon is displayed close to the band in use or to the menu settings. 16/18. Indicates the channel number that you stored Battery Level Indicator When the battery level indicator reads the battery is depleted.
or UHF) in the main or secondary display. When listening to broadcast FM, the / key switches between 65-75 MHz and 76-108 MHz band. Press and hold this key for 5 seconds to switch between GMRS communication and NoAA weather reception mode. • Numeric keypad With these keys you can input the information or your selections on the radio. In tx mode, push the number keys to send a corresponding DTMF code. •* Key A short momentary press of the key enables the reverse function.
5. BASIC OPERATIONS 5.1 Power on the radio • Turning the unit on To turn the unit on, simply rotate the volume/power knob clockwise until you hear a "click". If your radio powers on correctly there should be an audible double beep after about one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode".
5.4 Making a call NOTE: Press the / key to switch the main channel to the other channel if there are 2 channels shown on the display. In standby mode, press and hold the key to switch between frequency (VFO) mode and channel (MR) mode. • Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Initiate a call, the red LED is on.
WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offence. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules and regulations apply to your area. 5.
6.2 Channel scanning Use scan to search the channels for transmissions from unknown parties, to find someone in your group who has accidentally changed channels or to quickly find unused channels for your own use. a. In channels mode, press key for more than 2 seconds. The radio will start scanning according to the channel you set. b. You can change the scanning direction with the / keys. c. Press key to stop scanning. Note: for Scan mode, see Menu No.19. 6.
receiving and transmitting frequencies; while in channel mode the two different channels will be displayed. Important2: In frequency or channel mode, press the / key to shift between the main channel A and the sub-channel B on the display indicates on which channel (main channel A or sub channel B) you are operating. 6.7 Keypad lock This function locks the keypad to prevent accidental pressure of the controls. To unlock the keypad, press [* ] for more than 2 seconds. 6.
Frequency Mode vs. Channel Mode In standby mode, press and hold the key to switch between frequency (VFO) mode and channel (MR) mode. These two modes have different functions and are often confused. Frequency Mode (VFO) : Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted. Channel Mode (MR) : Used for selecting preprogrammed channels. Ex 1. Programming a Scan Channel with CTCSS Tone EXAMPLE New memory in Channel 31: RX = 432.
B. Press and hold the key to set the radio to VFO mode, and the VFO icon is displayed on the right. C. [1][8] Enter the scan range menu D. Enter [4][3][0][4][3][5] [ ] Enter the scan frequency range E. Press and hold the key to start frequency Frequency required for scanning scan, 432.55000 frequency points start to scan. There is activity, stay here temporarily, press [PTT] key to stop scanning, confirm the required frequency. Stop scanning, the required storage frequency F.
NOAA weather scan. The radio will stop scanning and the display will show the current WX Band channel setting. To turn the NOAA weather receiver off, press the / key. Note: NOAA weather radio stations are assigned to cover specific areas and service may be limited. Please check with your local weather office for frequency and details or visit www.weather.gov/nwr in the US to view the appropriate transmitter for your area.
A. Press the key to enter the menu. B. Use the numerical keypad to enter the number of the menu item. C. To enter the menu item, press the key. D. For entering the desired parameter you have two options: a). Use the arrow keys as we did in the previous section; or b). Use the numerical keypad to enter the numerical short-cut code. E. And just as in the previous section; a). To confirm your selection, press and it will save your setting and bring you back to the main menu. b).
You have 5 selections available: Off/ Mode 1/ Mode 2/ Mode 3/ Mode 4. For example: Mode 1= 1s’ working and 1s’ battery saving. Mode 2= 1s’ working and 2s’ battery is saving. NOTE: The higher the number the longer the battery lasts. The higher number increases the RX sleep cycle, but you may miss the first few syllables before the RX opens (4) VOX Function (Vox Level ) - MENU No.
Note: If this option is set to OFF, press and hold the PTT key to keep transmission. (10) Receiving DCS (Rx DCS) - MENU No.9 DCS codes are similar to access codes and can be added to channels, so as to create a sort of personal channel. They enable the radio to communicate with the users that are tuned on the same channel and have set the same DCS code.
(15) ANI-ID (ANI-ID) - MENU No.14 With this function you can set your ID-code. It can be programmed by the proper programming software. You can edit up to 5 digits. (16) DTMFST (DTMFST) - MENU No.15 Determines when DTMF Side Tones can be heard from the transceiver speaker.
Thanks to this function, P15UV can SCAN in frequency or channel mode. You can choose amongst three options: • Time-operated SCAN Whenever a signal is detected, the radio will suspend the SCAN for 5 seconds, and then will continue to SCAN even if the signal is still present. • Carrier-operated SCAN Whenever a signal is detected, the radio will stop scanning. It will resume to SCAN once the signal will disappear. • Search -Search SCAN The radio will stop scanning once a signal is detected.
• Frequency: Frequency + channel No. • Name: Channel name Note: Channel name mode must be set by the programming software. Up to three numbers or characters can be edited. (24) Busy Channel Lock (Busy Lock) - MENU No. 23 When this function is on, it may prevent other radios’ interference. If the selected channel is being used by other radios, when you press key PTT, your radio cannot transmit. Release the PTT and transmit as soon as the frequency is no longer busy.
NOTES: If you want to set CTCSS tones, DCS codes or the frequency offset, you have to do it before storing the channel. The channels already stored are displayed as CH-XXX ("CH" and -channel number), and other channels only display channel numbers. (29) Channel Delete (Delete) - MENU No.28 In this menu you can delete a channel of the radio. (30) Alarm Mode (Alarm Mode) - MENU No.29 This function can set the tone alarm/code alarm/site alarm of the radio.
(34) Squelch tail elimination of repeater (RP-STE) - Menu No. 33 This function is used when the radio operates through a repeater; when the PTT is released, the repeater will emit the end transmission tone to confirm it is working. Available settings: Off, 1,2,3,4,5,….10 to set the delay time. Note: Please disable this function in normal using, lest affect your normal conversation. (35) Delay the squelch tail of repeater (RPT-RL) - Menu No.
(39) Language selection (Language) - Menu No. 38 With this function, you can select the language of the LCD display and operation prompt. (40) Frequency hopping system (Hopping RX) - MENU No. 39 With this function, you can activate the frequency hopping system, improve the anti-interference ability of the radio, and reduce the risk of being monitored. (41) Reset (Reset) - Menu No.40 With this function you can reset the transceiver to the factory-programmed settings and parameters.
8. ON-LINE SERVICE AND SUPPORT The POFUNG website provides additional information about obtaining service or support for the POFUNG line of two-way radios and accessories. Visit: www.pofungshop.com Warning Notes every effort has been made to ensure that the information in this document is complete, accurate, and up to-date. POFUNG Radio assumes no responsibility for the results of errors beyond its control.
Appendix A. – Trouble shooting guide Phenomena Analysis Solution The battery may be installed improperly. Remove and reattach the battery. The battery power may run out. Recharge or replace the battery. You cannot turn on the radio. The battery may suffer from poor contact caused Clean the battery contacts or replace the by dirty or damaged battery contacts. battery. The battery voltage maybe low. Recharge or replace the battery. The volume level may be low. Increase the volume.
Appendix B. - Technical Specifications General Frequency Range Memory Channel Operation Voltage Battery Capacity Frequency Stability Operating Temperature Mode of Operation Antenna Impedance GRSM(RX & TX) 136-174 & 400-512MHz(RX) 30 GMRS+11 NoAA weather Channels+220 Scanner DC 7.4 V ±10% 1500mAh (Li-Ion) ±2.5ppm -20℃ to +50℃ Simplex 50ohm Transmitter Part RF Output Power FM Modulation Adjacent Channel Power Transmission current ≤5W(GMRS) 11K0F3E@12.5KHz 60dB @ 12.
Appendix C. - Shortcut Menu operations MENU No. Name (Full Name) Enter item 0 Squelch - Squelch Level MENU+0 0-9 Levels 0:Lowest 9:Highest 1 Step –Step Frequency MENU+1 2.5K/5.0K/6.25K/10.0K 12.5K/20.0K/25.0K/50.0K MENU+3 OFF: 1, 2, 3, 4 2 Power Save Battery Saving LCD display Selectable 3 Vox Level - VOX MENU+3 GMRS Version not support 4 Bandwidth /Narrow Bandwidth MENU+4 Narrow:12.5K 5 Backlight –Auto Backlight MENU+5 Bright/1,2,3…8，9,10Sec *Time-out for the LCD backlight.
6 D.Wait – Dual Watch Operation MENU+6 Off On *Monitor [A] and [B] at the same time. The display with the most recent activity ([A] or [B]) becomes the selected display. 7 Beep- Keypad Beep MENU+7 Off On *Allows audible confirmation of a key press. MENU+8 15,30…600S *This feature provides a safety switch that limits transmission time to a programmed value.
MENU+11 Off D023N…D754N; D023I …D754I *Transmits a specific low-level digital signal to unlock the squelch of a distant receiver (usually a repeater). 12 Tx CTCSS Transmitter CTCSS MENU+12 Off 67.0HZ…254.1HZ *Transmits a specific and continuous sub audible signal to unlock the squelch of a distant receiver (usually a repeater). 13 Voice - Voice Reminding MENU+13 Off On *Allows audible voice confirmation of a key press. 14 ANI-ID MENU-14 Displays the ANI code that has been set by software.
ON: the current channel is added to the scan, the scan current channel OFF: Do not scan the current channel. 17 Scan Add-Scan channel add 18 Scan Ran- Scan Frequency Range MENU+18 19 Scan Mode Scanner Resume Method MENU+19 20 PTT-ID - PTT-ID MENU+20 21 MDF-A - Channel A Display Mode MENU+21 Frequency: Displays programmed Frequency Name: Displays the channel name *Note: Names must be entered using software.
Off On *Disables the [PTT] button on a channel that is already in use. The transceiver will sound a beep tone and will not transmit if the [PTT] button is pressed when a channel is already in use. Off On *When ON, the keypad will be locked if not used in 8 seconds. Pressing the [* ] key for 2 seconds will unlock the keypad.
29 Alarm Mode Alarm Mode MENU+29 Site: Sounds alarm through your radio speaker only Tone: Sending alarm tone Code: Sending alarm code 30 SEEK CTC -Scan of frequencies with CTCSS MENU+30 67.0HZ,…,254.
MENU+36 1000Hz/1450Hz/1750Hz/2100Hz *To send out a repeater tone; You hold down the [PTT] + [LAMP/MONI] key. 37 OPNSET -Power On Message MENU+37 Logo: Performs an LCD screen test at power-on Msg : Displays a 2-line power on message Voltage: *Controls the behavior of the display when the transceiver is turned on.
Appendix D. - GMRS Frequency Chart (MHz) CH.No CH.Freq. Type of Radio Power Output CH.No CH.Freq. Type of Radio Power Output 1 462.5625 GMRS High 2 462.5875 GMRS High 16 462.5750 GMRS High 17 462.6000 GMRS 3 462.6125 GMRS High High 18 462.6250 GMRS High 4 462.6375 5 462.6625 GMRS High 19 462.6500 GMRS High GMRS High 20 462.6750 GMRS 6 High 462.6875 GMRS High 21 462.7000 GMRS High 7 462.7125 GMRS High 22 462.7250 GMRS High 8 467.
Appendix E.
101 106 111 116 121 126 131 136 141 146 151 156 161 166 171 176 181 186 191 196 201 206 D731N D023I D036I D054I D074I D125I D145I D165I D223I D245I D261I D274I D331I D356I D412I D445I D462I D506I D546I D627I D662I D731I 102 107 112 117 122 127 132 137 142 147 152 157 162 167 172 177 182 187 192 197 202 207 D732N D025I D043I D065I D114I D131I D152I D172I D225I D246I D263I D306I D332I D364I D413I D446I D464I D516I D565I D631I D664I D732I 103 108 113 118 123 128 133 138 143 148 153 158 163 168 173 178 183
Appendix F. - CTCSS Table CTCSS CHART (Hz) Number 1 6 11 16 21 26 31 36 41 46 Frequency 67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1 Number 2 7 12 17 22 27 32 37 42 47 Frequency 69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6 Number 3 8 13 18 23 28 33 38 43 48 Frequency 71.9 85.4 100 118.8 141.3 162.2 177.3 192.8 210.7 241.8 Number 4 9 14 19 24 29 34 39 44 49 Frequency 74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3 Appendix G.
Disclaimer The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company.
