Owners manual
©2015 POISON SPYDER CUSTOMS 951-849-5911•WWW.POISONSPYDER.COM
INSTALLATION INSTRUCTIONS INST-14-16-020_A
TJ-YJ-CJ BFH™ Front
Bumpers
IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation. If you are not
confident in your mechanical skills, please seek the help of a professional to perform the installation. Check your packages immediately upon arrival to ensure that
everything listed is included, and to check for damage during shipping. If anything is missing or damaged, or if you need technical assistance with any aspect of
this installation, call Poison Spyder at (951) 849-5911 as soon as possible. This document last updated May 2015.
APPLICATIONS
These installation instructions apply to the following
Poison Spyder products:
14-16-020 TJ BFH Front Bumper
14-16-020-D TJ BFH Front Bumper - Tabs
14-16-020-B TJ BFH Front Bumper - Brawler Bar
14-16-020-DB TJ BFH Front Bumper - Brawler Bar - Tabs (shown)
14-16-020-C TJ BFH Front Bumper - Comp Stinger
14-16-020-DC TJ BFH Front Bumper - Comp Stinger - Tabs
14-16-020-S TJ BFH Front Bumper - Trail Stinger
14-16-020-DS TJ BFH Front Bumper - Trail Stinger - Tabs
13-16-020 YJ BFH Front Bumper
13-16-020-D YJ BFH Front Bumper - Tabs
13-16-020-B YJ BFH Front Bumper - Brawler Bar
13-16-020-DB YJ BFH Front Bumper - Brawler Bar - Tabs
13-16-020-C YJ BFH Front Bumper - Comp Stinger
13-16-020-DC YJ BFH Front Bumper - Comp Stinger - Tabs
13-16-020-S YJ BFH Front Bumper - Trail Stinger
13-16-020-DS YJ BFH Front Bumper - Trail Stinger - Tabs
11-16-020 CJ BFH Front Bumper
11-16-020-D CJ BFH Front Bumper - Tabs
11-16-020-B CJ BFH Front Bumper - Brawler Bar
11-16-020-DB CJ BFH Front Bumper - Brawler Bar - Tabs
11-16-020-C CJ BFH Front Bumper - Comp Stinger
11-16-020-DC CJ BFH Front Bumper - Comp Stinger - Tabs
11-16-020-S CJ BFH Front Bumper - Trail Stinger
11-16-020-DS CJ BFH Front Bumper - Trail Stinger - Tabs
PARTS LIST
(1) BFH Front Bumper
TOOLS NEEDED
• Torx T55 socket
• Ratchet
• Torque wrench
• Measuring tape
• Soft dead blow hammer or mallet
• Fine-tip felt marker, 1/2” drill bit and drill motor (CJ models
only)
BEFORE YOU BEGIN
The Poison Spyder Customs BFH Front Bumper
comes as un-painted, bare steel. You will want
to either powder coat or paint the bumper prior to
install. If painting yourself, careful preparation will
make a big difference in the quality and longevity of
your paint job, even using “rattle can” aerosol paints.
Begin by thoroughly cleaning the Stinger with solvent
or degreaser, then make sure all residue is removed.
Even if you use cheap paint, try to use a good quality
primer. “Etching” primers are best to use on bare, un-
painted metal. Allow it to properly dry before paitning,
and between paint coats.
INSTALLATION PROCEDURE
1. Park the Jeep on a flat, level surface and set the
parking brake.
2. Remove existing front bumper. If it is still the
OEM bumper and hardware, there are four bolts (two on
the top and two on the bottom that hold the bumper in
place). These will likely be Torx bolts, use a T55 Torx bit.
3. Place the BFH Front Bumper on to the frame rails,
in place of the bumper that was removed. Visually align
the bumper mounting slots with the threaded holes in the
frame rails. Take measurements to ensure that the bumper
is installed square to the frame and grill. Use a soft dead-
blow hammer, if necessary, to make fine adjustments.
4. On CJ models, use a fine-tip felt marker to mark
through the rearward winch mounting holes (closest to the