PoStepVID6606 User’s manual V1.
PoStepVID6606 User's Manual 15. december 2020 Please read the following notes 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. 2. PoLabs does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of PoLabs products or technical information described in this document.
PoStepVID6606 User's Manual 15. december 2020 Contents 1 Introduction..................................................................................................................................... 4 2 Features ........................................................................................................................................... 4 3 Connectors and pinout .................................................................................................................... 4 3.
PoStepVID6606 User's Manual 15. december 2020 1 Introduction PoStepVID6606 board contains two driver chips VID6606 and so allows the user to drive up to eight miniature stepper motors with current up to 35mA. Device uses a simple serial bus protocol. Along with a PoKeys57U or PoKeys57E device, the board is a great choice when building a flight or other simulators with instrumental display panels.
PoStepVID6606 User's Manual 15. december 2020 3.1 PoExtensionIn Pin 1 2 3-7 8 9 10 Function GND Data signal (SER) Data signal (SCK) Data signal (RCK) Pin 1 2 Power supply From +12 to +24V DC GND 3.2 Supply voltage 3.3 Backlight supply voltage Backlight voltage is distributed only to the Micro-MaTch stepper motor terminals, and no internal electronics are used. Use the appropriate external voltage for the backlight. Pin 1 2 + - Backlight supply Max 500mA (dc or ac voltage) 3.
PoStepVID6606 User's Manual 15. december 2020 3.5 Stepper motor Micro-MaTch connectors Pin 1 2 3 4 5 6 7 8 Motor1 … Motor8 Backlight + Backlight Backlight + Backlight A1 Coil A A2 B1 Coil B B2 4 PoStepVID6606 and PoKeys PoStepVID6606 is shipped with the cable attached to the PoExtensionIn. To use device together with PoKeys57E/PoKeys57U, connect the flat cable to the appropriate pins of PoKeys57E/57U device as shown below. PoStepVID6606 uses 3 input pins and GND to communicate with master device.
PoStepVID6606 User's Manual 15. december 2020 5 Serial protocol - step/direction signals The PoStepVID6606’s digital TTL data input levels are +3.3V and +5V compatible. The serial data length is 16-bit and contains step and direction signal for 8 motor driver inputs.
PoStepVID6606 User's Manual 15. december 2020 6 Technical specifications • • • • • • • • • Supply voltage 12-24 VDC Power consumption max 2.5 W Data inputs signal TTL 3.3 V ÷ 5 V Serial bus fmax 30 MHz Motor coil current max (Icoil) 35 mA Driver step/direction signals fmax 500kHz Working temperature -20 °C ÷ +80 °C Weight 40g Mechanical dimensions [mm] 8 www.PoLabs.
PoStepVID6606 User's Manual 15. december 2020 7 Grant of license The material contained in this release is licensed, not sold. PoLabs grants a license to the person who installs this software, subject to the conditions listed below. 7.1.1 Access The licensee agrees to allow access to this software only to persons who have been informed of and agree to abide by these conditions. 7.1.2 Usage The software in this release is for use only with PoLabs products or with data collected using PoLabs products. 7.
