POLAR s3+ STRIDE SENSOR User Manual
1. 2. 3. 4. 5.
ENGLISH Congratulations! The Polar s3+ stride sensorTM W.I.N.D. is the best choice for improving your running technique and efficiency. Using sensitive inertial sensors to track the position of the foot it gives accurate and highly responsive speed, distance, leg cadence and stride length measurements. The latest version of this user manual can be downloaded at www.polar.com/support. For video tutorials, go to www.polar.com/en/polar_community/videos. Please follow the pictures on the front cover.
3. 4. Place the cover with the battery inside it into the sensor. Press the cover in place and close it by turning clockwise from OPEN to CLOSE using a coin (see picture 3). Teach a New Stride Sensor to Your Training Computer Your new s3+ stride sensor must be introduced to your Polar training computer in order to analyze your running technique and efficiency. This is called teaching. For further information, refer to the training computer user manual or go to www.polar.com/support.
3. 4. 5. Tighten the laces. Fit the front part of the sensor into the holder and press from the rear (see picture 5). Fasten the flap. Make sure the sensor does not move and is aligned with your foot. The more secure the sensor, the more accurately speed and distance is measured. Calibrate the s3+ Stride Sensor Calibration of the stride sensor improves the accuracy of speed, pace and distance measurements.
Calibrate stride sensor during training (on-the-fly calibration): You can calibrate the stride sensor at any phase of your training session with actual distance correction, when you have run a known distance, preferably more than 1000 meters, calibrate the stride sensor as instructed in the user manual for the Polar product in question. Set calibration factor manually: The calibration factor is calculated as a ratio of the actual distance to the uncalibrated distance.
kits with sealing rings are available at well-equipped Polar retailers and authorized Polar Service Centers. In the USA and Canada, sealing rings are available at authorized Polar Service Centers only. If you would prefer Polar to replace the battery, contact an authorized Polar Service Center. The Service will test the stride sensor after replacing the battery. Keep batteries away from children. If swallowed, contact a doctor immediately.
Technical Specifications Battery life: Battery type: Battery sealing ring: Operating temperature: Accuracy: Average 200 hours of use CR2430 O-Ring 25.0 x 1.
consequential or special, arising out of, or related to the product. • Items purchased second hand are not covered by the two (2) year warranty, unless otherwise stipulated by local law. • During the guarantee period, the product will be either repaired or replaced at any of the authorized Polar Service Centers regardless of the country of purchase. Guarantee with respect to any product will be limited to countries where the product has been initially marketed.
Compliance Statement Canada Polar Electro Oy has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Polar Electro Oy n’a approué aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou toute modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.
Avis de conformité à la réglementation d’Industrie Canada Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.
FCC regulatory information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
This product emits radio frequency energy, but the radiated output power of this device is far below the FCC radio frequency exposure limits. This equipment complies with FCC RF radiation exposure limits forth for an uncontrolled environment. Nevertheless, the device should be used in such a manner that the potential for human contact with the antenna during normal operation is minimized.
Disclaimer • The material in this manual is for informational • • 12 purposes only. The products it describes are subject to change without prior notice, due to the manufacturer’s continuous development program. Polar Electro Inc. / Polar Electro Oy makes no representations or warranties with respect to this manual or with respect to the products described herein. Polar Electro Inc.
Manufactured by Polar Electro Oy Professorintie 5 FIN-90440 KEMPELE Tel +358 8 5202 100 Fax +358 8 5202 300 www.polar.
