Pantone 426 C Sportsman Big Boss 6X6 Owner's Manual for Maintenance and Safety Read this manual carefully. It contains important safety information. This is an adult vehicle only. Operation is prohibited for those under 16 years of age.
WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
The text is printed on 100% recycled with 40% post-consumer waste (PCW).
Pantone 426 C Improper vehicle use can result in SEVERE INJURY or DEATH. NEVER: S Operate on public roads. A collision can occur with another vehicle. S Carry passengers. Passengers affect balance and steering and increase risk of losing control. S USE ALCOHOL or DRUGS before or while operating this vehicle. S Operate at speeds too fast for your skills or the conditions. S Operate this vehicle on HILLS steeper than 25 degrees. To prevent flipover on hilly terrain, use throttle and brakes gradually.
WELCOME Thank you for purchasing a Polaris vehicle, and welcome to our worldwide family of Polaris owners. We proudly produce an exciting line of utility and recreational products. • Snowmobiles • All-terrain vehicles (ATVs) • RANGER® utility vehicles • Victory Motorcycles® We believe Polaris sets a standard of excellence for all utility and recreational vehicles manufactured in the world today.
POLARIS, THE WAY OUT, SPORTSMAN and BIG BOSS are registered trademarks of Polaris Industries Inc. Copyright 2009 Polaris Sales Inc. All information contained within this publication is based on the latest product information at the time of publication. Due to constant improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication.
TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features and Controls . . . . . . . . . . . . . . . . . . . 26 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Emission Control Systems . . . . . . . . . . . . . . . 66 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Troubleshooting . .
INTRODUCTION The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and symbols are used. Become familiar with their meanings before reading the manual. The safety alert symbol indicates a potential personal injury hazard. WARNING A WARNING indicates a hazardous situation which, if not avoided, may result in death or serious injury.
INTRODUCTION WARNING Failure to heed the warnings and safety precautions contained in this manual can result in severe injury or death. This Polaris vehicle is not a toy and can be hazardous to operate. This vehicle handles differently than other vehicles, such as motorcycles and cars. A collision or rollover can occur quickly, even during routine maneuvers like turning, or driving on hills or over obstacles, if you fail to take proper precautions. • Read this owner’s manual.
INTRODUCTION Vehicle Identification Numbers Record your vehicle's identification numbers and key number in the spaces provided. Remove the spare key and store it in a safe place. An ignition key can be duplicated only by ordering a Polaris key blank (using your key number) and mating it with one of your existing keys. The ignition switch must be replaced if all keys are lost.
SAFETY Safety Training ATV safety training is a top priority for Polaris. Polaris strongly encourages you and any family members who will be riding the ATV to take a training course. If you purchased a new Polaris ATV in the United States, your dealer provided instruction to you about the authorized ATV RiderCoursesm that is available to you and your eligible family members. This training is included in the purchase price of your ATV.
SAFETY Safe Riding Gear Always wear appropriate clothing when riding this vehicle. Wear protective clothing for comfort and to reduce the chance of injury. Eye Protection Gloves Helmet Long Sleeves Long Pants Boots Helmet Wearing a helmet can prevent a severe head injury. Whenever riding a Polaris vehicle, always wear a helmet that meets or exceeds established safety standards. Approved helmets in the USA and Canada bear a U.S. Department of Transportation (DOT) label.
SAFETY Safe Riding Gear Eye Protection Do not depend on eyeglasses or sunglasses for eye protection. Whenever riding a Polaris vehicle, always wear shatterproof goggles or use a shatterproof helmet face shield. Polaris recommends wearing approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8, Z87.1, or CE. Make sure protective eye wear is kept clean. Gloves Off-road style gloves with knuckle pads are the best for comfort and protection.
SAFETY WARNING Failure to operate the vehicle properly can result in a collision, loss of control, accident or overturn, which may result in serious injury or death. Heed all safety warnings outlined in this section of the owner’s manual. See the OPERATION section of the owner’s manual for proper operating procedures. Operating Without Instruction Operating this vehicle without proper instruction increases the risk of an accident.
SAFETY Safety Warnings Handling Gasoline Gasoline is highly flammable and explosive under certain conditions. • Always exercise extreme caution whenever handling gasoline. • Always refuel with the engine stopped, and outdoors or in a well ventilated area. • Do not smoke or allow open flames or sparks in or near the area where refueling is performed or where gasoline is stored. • Do not overfill the tank. Do not fill the tank neck.
SAFETY Safety Warnings Protective Apparel Riding on this vehicle without wearing an approved helmet and protective eyewear increases the risk of a serious injuries in the event of an accident. Operator and passenger must always wear an approved helmet that fits properly and eye protection (goggles or face shield). Using Alcohol or Drugs Operating the vehicle after consuming alcohol or drugs could adversely affect operator judgment, reaction time, balance and perception.
SAFETY Safety Warnings Operating on Pavement Operating this vehicle on paved surfaces (including sidewalks, paths, parking lots and driveways) may adversely affect the handling of the vehicle and could result in loss of control and accident or overturn. Avoid operating the vehicle on pavement. The tires are designed for off-road use. If it's unavoidable, travel slowly and avoid sudden turns or stops.
SAFETY Safety Warnings Physical Control of the Vehicle Removing a hand from the handlebars or feet from the footrests during operation can reduce your ability to control the vehicle or cause loss of balance and ejection from the vehicle. If the operator's foot is not firmly planted on the footrest, it could also contact the rear wheels. Never remove your hands from the handlebars while operating, and always keep both feet on the footrests.
SAFETY Safety Warnings Descending Hills Improperly Improperly descending a hill could cause loss of control or overturn. • Always follow proper procedures for traveling down hills as described in the owner's manual. NOTE: A special technique is required when braking while traveling downhill. See page 57. • Always descend a hill with the transmission in forward gear. Do not descend a hill with the transmission in neutral.
SAFETY Safety Warnings Stalling While Climbing a Hill Stalling, rolling backwards or improperly dismounting while climbing a hill could cause an overturn. • Always maintain a steady speed when climbing a hill. • Always move the 4X4 switch to ADC 4X4 (if equipped) before ascending or descending a hill. See page 36. If all forward speed is lost: • Keep body weight uphill. • Apply the service brakes. • Lock the parking brake when fully stopped.
SAFETY Safety Warnings Operating on Steep Hills Operating on excessively steep hills could cause an overturn. Never operate on hills too steep for the vehicle or for your abilities. Never operate the vehicle on hills steeper than 25 degrees. Operating on Slippery Terrain Failure to use extra caution when operating on excessively rough, slippery or loose terrain could cause loss of traction, loss of control, accident or overturn. Do not operate on excessively rough, slippery or loose terrain.
SAFETY Safety Warnings Improper Tire Maintenance Operating this vehicle with improper tires or with improper or uneven tire pressure could cause loss of control or accident. Always use the size and type of tires specified for your vehicle. Always maintain proper tire pressure as described in the owner's manual and on safety labels. Operating Over Obstacles Improperly operating over obstacles could cause loss of control or overturn. Before operating in a new area, check for obstacles.
SAFETY Safety Warnings Improper Cargo Loading Overloading the vehicle or carrying/towing cargo improperly may cause changes in handling, which could cause loss of control or an accident. • Never exceed the stated load capacity for this vehicle. • Cargo should be properly distributed and securely attached. • Reduce speed when carrying cargo or pulling a trailer. Allow a greater distance for braking. • Always follow the instructions in the owner's manual for carrying cargo or pulling a trailer.
SAFETY Safety Warnings Operating Through Deep Water Operating the vehicle through deep or fast-flowing water could cause the tires to float, causing loss of control or overturn. Avoid operating the vehicle through deep or fast-flowing water. If it's unavoidable to enter water that exceeds the recommended maximum depth (see page 59): • Travel slowly. • Balance your weight carefully. • Avoid sudden movements. • Maintain a slow and steady forward motion.
SAFETY Safety Warnings Operating a Damaged Vehicle Operating a damaged vehicle can result in an accident. After any overturn or accident, have a qualified service dealer inspect the entire machine for possible damage, including (but not limited to) brakes, throttle and steering systems. Physical Skills Safe operation of this rider-active vehicle requires good judgement and physical skills.
SAFETY Safety Labels and Locations Warning labels have been placed on the vehicle for your protection. Read and follow the instructions of the labels on the vehicle carefully. If any of the labels depicted in this manual differ from the labels on your vehicle, always read and follow the instructions of the labels on the vehicle. If an informational or graphic label becomes illegible or comes off, contact your Polaris dealer to purchase a replacement.
SAFETY Safety Labels and Locations General Warning + Reverse Override Warning + + Tire Pressure/Load Warning + Front Rack Warning Tire Pressure/Load Warning WARNING Improper tire pressure or overloading can cause loss of control. Loss of control can result in severe injury or death. • Cold tire pressure: Front: 7.0 psi (48.3 kPa) Center: 10.0 psi (68.9 kPa) Rear: 10.0 psi (68.9 kPa) • Maximum weight capacity: 1115 lbs. (507 kg) 7175651 Front Rack/Box Warning WARNING • DO NOT TOW FROM RACK OR BUMPER.
SAFETY Safety Labels and Locations Age 16 Warning + Container/No Passenger Warning + + Clutch Cover Warning Container/No Passenger Warning WARNING Remove flammable containers from box before refueling. WARNING • Passengers can be thrown off. This can cause serious injury or death. • Never carry passengers. Maximum Box Load 800 lbs.
SAFETY Safety Labels and Locations Age 16 Warning WARNING Operating this ATV if you are under the age of 16 increases your chance of severe injury or death. NEVER operate this ATV if you are under age 16. 7172588 Clutch Cover Warning WARNING • Moving parts hazard under belt-clutch guard. To prevent serious injury, do not operate vehicle with guard removed. • Do not modify engine or clutch.
FEATURES AND CONTROLS Switches Headlight Switch 4X4 Switch Mode/Reverse Override Switch Main Key Switch Engine Stop Switch Mode/Reverse Override Switch This vehicle is equipped with a reverse speed limiter system.To gain additional wheel speed while backing, release the throttle and depress the override button. WARNING! Pressing the override button while the throttle is open can cause loss of control, which may result in serious injury or death.
FEATURES AND CONTROLS Switches Engine Stop Switch Move the stop switch either left or right to the OFF position to stop the engine quickly. The engine will not start or run OFF RUN OFF when the switch is off. Both the main switch and the engine stop switch will shut off all electrical power to the vehicle, including lights. Main Key Switch Use the main key switch to start the engine. See page 51 for starting procedures.
FEATURES AND CONTROLS Throttle Lever WARNING Operating this vehicle with sticking or improperly operating throttle controls could cause an accident. Never start or operate the vehicle if it has a sticking or improperly operating throttle. Always contact your dealer for service before operating the vehicle. Failure to check or maintain proper operation of the throttle system can result in an accident if the throttle lever sticks during operation.
Brake Systems FEATURES AND CONTROLS WARNING Aggressively applying the rear brake when backing down a hill may cause rear tipover, which could result in serious injury or death. Never back down a hill. Use caution when applying the rear brake. Do not aggressively apply the rear brake when going forward. The rear wheels may skid and slide sideways, causing loss of control, which may result in serious injury or death.
FEATURES AND CONTROLS Brake Systems Service Brake Lever Squeeze the service brake lever (left lever) toward the handlebar to apply the front and rear brakes. These brakes are hydraulically activated disc brakes. Always test brake lever travel and master cylinder fluid level before riding. When squeezed, the lever should feel firm. Any sponginess would indicate a possible fluid leak or low master cylinder fluid level, which must be corrected before riding.
FEATURES AND CONTROLS Master Cylinder/Brake Fluid WARNING An over-full master cylinder may cause brake drag or brake lock-up, which could result in an accident. Maintain brake fluid at the recommended level. Do not overfill. Never store or use a partial bottle of brake fluid. Brake fluid is hygroscopic, meaning it rapidly absorbs moisture from the air.
FEATURES AND CONTROLS Parking Brake Locking the Parking Brake 1. Place the transmission in park. 2. Squeeze and release the brake lever two or three times, then squeeze and hold. 3. Push the parking brake lock forward to engage the lock. 4. Release the brake lever. 5. To release the parking brake lock, squeeze and release the brake lever. It will return to its unlocked position. WARNING! Operating the vehicle while the parking brake is engaged could result in an accident or fire.
FEATURES AND CONTROLS Automatic Transmission Gear Selector The transmission gear selector is located on the right side of the vehicle. H: High Gear L: Low Gear N: Neutral R: Reverse P: Park To shift gears, brake to a complete stop. When the engine is idling, move the lever to the desired gear. Gear Selector NOTICE: Shifting gears with the engine speed above idle or while the vehicle is moving could cause transmission damage.
FEATURES AND CONTROLS All Wheel Drive (AWD) System The All Wheel Drive system is controlled by the 4X4 (AWD) switch. ADC 4X4 Mode (if equipped) When the switch is on ADC 4X4, the ADC system allows engine braking to all six wheels when the vehicle descends a hill or incline. Always move the 4X4 switch to ADC 4X4 before ascending or descending a hill. See page 36.
FEATURES AND CONTROLS All Wheel Drive System Engaging AWD The 4X4 switch may be turned on or off while the vehicle is moving. Initially, the vehicle's electronic system will not enable AWD until the engine RPM is below 3100. Once enabled, AWD remains enabled until the 4X4 switch is turned off. If the switch is turned off while the demand drive unit is moving, it will not disengage until the rear wheels regain traction.
FEATURES AND CONTROLS Active Descent Control (ADC) System The ADC system (if equipped) allows engine braking to all four wheels when the vehicle descends a hill or incline. Always move the 4X4 switch to ADC 4X4 before ascending or descending a hill.
FEATURES AND CONTROLS Instrument Cluster Your vehicle is equipped with an instrument cluster that senses vehicle speed from the right front wheel. In addition to showing vehicle speed, the speedometer needle flashes when a warning condition exists. The instrument cluster measures distance in miles as well as hours of operation. It also includes a reverse speed limiter function that limits the vehicle's speed to approximately 7-9 mph (11-14 km/h). Refer to page 26 for additional information.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center The rider information center is located in the instrument cluster. All segments will light up for 2.5 seconds at start-up. If the instrument cluster fails to illuminate, a battery over-voltage may have occurred and the instrument cluster may have shut off to protect the electronic speedometer. If this occurs, take the vehicle to your Polaris dealer for proper diagnosis. 1.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center Standard Modes Use the MODE button to toggle through the mode options. The reverse override button is also the MODE button. See page 26. The transmission cannot be in reverse when using this feature. Odometer Mode The odometer records the miles traveled by the vehicle. Trip Meter Mode The trip meter records the miles traveled by the vehicle on each trip if it's reset before each trip. To reset the trip meter, select the trip meter mode.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode The wrench icon will display when the gauge is in the diagnostic mode. To exit the diagnostic mode, turn the key switch off and on. Any movement of the tires will also cause the gauge to exit the diagnostic mode. To enter the diagnostics mode: 1. Turn the key switch off and wait 10 seconds. 2. Lock the parking brake. 3. Place the transmission in neutral. 4. Hold the mode/reverse override button and turn the key switch on.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode Battery Voltage Screen View this screen to check battery voltage level. Tachometer Screen View the tachometer to check engine speed. 4X4 Diagnostic Screen The gauge indicates whether or not current is flowing through the allwheel-drive coil. This screen is for informational purposes only. Please see your dealer for all major repairs.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode Programmable service interval To enable or disable the service interval: 1. Enter the diagnostic mode. 2. Toggle to the service interval screen. 3. Press and hold the mode button for about 7 seconds, until either ON or OFF appears in the Rider Information Center, depending on your preference. To reset the service interval: 1. Enter the diagnostic mode. 2. Toggle to the service interval screen. 3.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center Downloading Codes The EFI diagnostic mode is for informational purposes only. Please see your Polaris dealer for all major repairs. See page 45 for Blink Codes and Failure Descriptions. Use the following procedure to download blink codes (failure codes) from the EFI module. 1. Place the transmission in park. 2. Stop the engine. 3. Turn the key switch to the ON position. 4.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center Downloading Codes Code Definitions Open Load: There is a break in the wires that lead to the item listed in the chart (injector, fuel pump, etc.), or the item has failed. Short-to-Ground: The wire is shorted to ground between the electronic control unit and the item listed in the chart. Shorted Load: The wires leading to the item listed in the chart are shorted together, or the item has shorted internally.
FEATURES AND CONTROLS Instrument Cluster Rider Information Center Downloading Codes Blink Code 12 22 22 22 25 31 31 36 36 37 37 41 41 42 42 44 45 46 47 47 51 51 52 52 55 55 56 56 58 58 59 59 63 63 72 73 73 74 74 61 Failure Description BEGIN SEQUENCE Throttle Position Sensor Low Throttle Position Sensor High Throttle Position Sensor Out of Adjustment Gear Sensor Signal System Voltage Low System Voltage High Ignition Coil A Prim/Sec Circuit Malfunction: Open Load/Short-to-Ground Ignition Coil A Prim/Sec Circ
OPERATION WARNING Failure to operate the vehicle properly can result in a collision, loss of control, accident or overturn, which may result in serious injury or death. Read and understand all safety warnings outlined in the safety section of this owner’s manual. Break-In Period The break-in period for your new Polaris vehicle is the first ten hours of operation, or the time it takes to use the first two full tanks of gasoline.
OPERATION Break-In Period Engine and Drivetrain Break-in 1. Fill the fuel tank with gasoline. See page 33. Always exercise extreme caution whenever handling gasoline. 2. Check the engine oil level on the dipstick. See page 72. Add oil if necessary to maintain the level between the safe and add marks. 3. Drive slowly at first. Select an open area that allows room to familiarize yourself with vehicle operation and handling. 4. Vary the throttle positions. Do not operate at sustained idle. 5.
OPERATION Pre-Ride Checklist Failure to inspect and verify that the vehicle is in safe operating condition before operating increases the risk of an accident. Always inspect the vehicle before each use to make sure it's in safe operating condition.
OPERATION Safe Operation Practices 1. Complete the recommended safety training before operating this vehicle. See page 7. 2. Do not allow anyone under 16 years of age to operate this vehicle. Do not allow anyone with cognitive or physical disabilities to operate this vehicle. 3. Never carry a passenger on this vehicle. 4. Engine exhaust fumes are poisonous. Never start the engine or let it run in an enclosed area. 5.
OPERATION Know Your Riding Area/Tread Lightly Familiarize yourself with all laws and regulations concerning the operation of this off-road vehicle in your area. Respect the environment in which you ride. Find out where the designated riding areas are by contacting your Polaris dealer, a local riding club or local officials. Help keep our trails open for recreational vehicle use. As an off-road enthusiast, you represent the sport and can set a good example (or a poor example) for others to follow.
OPERATION Starting the Engine 1. Position the vehicle on a level surface outdoors or in a well-ventilated area. 2. Place the transmission in park. 3. Lock the parking brake. Tip: The starter interlock will prevent the engine from starting if the transmission is in gear and the brake is not engaged. 4. Sit on the vehicle and move the engine stop switch to RUN. 5. Do not press the throttle while starting the engine. 6. Turn the ignition key past the ON position to engage the starter.
OPERATION Driving Procedures 1. Wear a helmet and eye protection. See page 8. 2. Sit upright with both feet on the footrests and both hands on the handlebars. 3. Start the engine and allow it to warm up. 4. Shift the transmission into gear. 5. Check your surroundings and determine your path of travel. 6. Release the parking brake. 7. Slowly depress the throttle with your right thumb and begin driving. 8. Drive slowly. Practice maneuvering and using the throttle and brakes on level surfaces.
OPERATION Turning the Vehicle Your vehicle is equipped with a solid rear axle, which drives both rear wheels equally at all times. This means that the wheel on the outside of the turn must travel a greater distance than the inside wheel when turning and the inside tire must slip traction slightly. To turn, steer in the direction of the turn, leaning your upper body to the inside of the turn while supporting your weight on the outer footrest.
OPERATION Driving on Slippery Surfaces Sideways skid Turn in direction of skid Whenever riding on slippery surfaces such as wet trails or loose gravel, or during freezing weather, follow these precautions: 1. Do not operate on excessively rough, slippery or loose terrain. 2. Slow down when entering slippery areas. 3. Engage 4X4 before wheels begin to lose traction. NOTICE: Severe damage to drive train may occur if the 4X4 is engaged while the wheels are spinning.
OPERATION Driving Uphill 25° Maximum Braking and handling are greatly affected when operating in hilly terrain. Improper procedure could cause loss of control or overturn. Whenever traveling uphill, follow these precautions: 1. Always move the 4X4 switch to ADC 4X4 (if equipped) before ascending or descending a hill. See page 36. 2. Drive straight uphill. 3. Avoid steep hills (25° maximum). 4. Always check the terrain carefully before ascending any hill. 5.
OPERATION Driving on a Sidehill (Sidehilling) Driving on a sidehill is not recommended. Improper procedure could cause loss of control or overturn. Avoid crossing the side of any hill unless absolutely necessary. If crossing a sidehill is unavoidable, follow these precautions: 1. Slow down. 2. Avoid crossing the side of a steep hill. 3. Shift body weight uphill. 4. Keep your feet on the footrests. 5.
OPERATION Driving Downhill When driving downhill, follow these precautions: 1. Always move the 4X4 switch to ADC 4X4 (if equipped) before ascending or descending a hill. See page 36. 2. Avoid steep hills (25° maximum). 3. Shift body weight uphill. 4. Drive straight downhill. 5. Slow down. Excessive speed when traveling downhill can cause loss of control. 6. Squeeze the brake lever gradually. Applying the brakes too firmly may cause the rear wheels to lock, which could result in loss of control.
OPERATION Turning Around on a Hill (K-Turn) If the vehicle stalls while climbing a hill, never back it down the hill! Use the K-turn to turn around. 8 ft. (2.4 m) 1. Stop and lock the parking brake while keeping body weight uphill. 2. Always move the 4X4 switch to ADC 4X4 (if equipped) before ascending or descending a hill. See page 36. 3. Leave the transmission in forward and shut off the engine. 4. Dismount on the uphill side of the vehicle, or on the left if the vehicle is pointing straight uphill. 5.
OPERATION Driving Through Water Your vehicle can operate through water with a maximum recommended depth equal to the bottom of the footrests. Follow these procedures when operating through water: 1. Determine water depths and current before entering water. 2. Choose a crossing where both banks have gradual inclines. 3. Avoid operating through deep or fast-flowing water. Maximum Depth NOTICE: Major engine damage can result if the vehicle is not thoroughly inspected after operation in water.
OPERATION Driving Over Obstacles Follow these precautions when operating over obstacles: 1. Always check for obstacles before operating in a new area. 2. Look ahead and learn to read the terrain. Be constantly alert for hazards such as logs, rocks and low hanging branches. 3. Travel slowly and use extra caution when operating on unfamiliar terrain. Not all obstacles are immediately visible. 4. Never attempt to operate over large obstacles, such as rocks or fallen trees.
OPERATION Driving in Reverse Follow these precautions when operating in reverse: 1. Always check for obstacles or people behind the vehicle. 2. Always avoid backing downhill. 3. Back slowly. 4. Apply the brakes lightly for stopping. 5. Avoid turning at sharp angles. 6. Never open the throttle suddenly. 7. Do not use the override button unless additional wheel speed is required for vehicle movement. Use the override with caution as rearward vehicle speed is greatly increased.
OPERATION Hauling Cargo WARNING Overloading the vehicle or carrying or towing cargo improperly can alter vehicle handling and may cause loss of control or brake instability, which can result in serious injury or death. Always follow these precautions when hauling cargo: • Never exceed the maximum weight capacity of the vehicle. When determining the weight you are adding to the vehicle, include the weight of the operator, accessories, loads in the rack or box and the load on the trailer tongue.
OPERATION Hauling Cargo Load cargo as far forward as possible 1. Always read and understand the load distribution warning labels on the vehicle, and never exceed the weight capacities outlined in the specifications section of the owner's manual and on the safety labels. The total load (operator, accessories, cargo and weight on hitch) must not exceed the maximum weight capacity of the vehicle. 2. Always load the cargo box with the load as far forward as possible. 3.
OPERATION Hauling Cargo Dumping Cargo 1. Select a level site to dump the cargo. Do not attempt to dump or unload the vehicle while parked on an incline. 2. Lock the parking brake. 3. Dismount the vehicle. 4. Check cargo distribution. If cargo has shifted to the rear of the box, exercise caution. WARNING! If the weight distribution in the box is located toward the rear of the box when the release lever is pulled forward, the box may dump on its own, which could cause serious injury.
OPERATION Parking on an Incline Avoid parking on an incline if possible. If it's unavoidable, follow these precautions: 1. Stop the engine. 2. Place the transmission in park. 3. Lock the parking brake. 4. Always block the rear wheels on the downhill side.
EMISSION CONTROL SYSTEMS Noise Emission Control System Do not modify the engine, intake or exhaust components, as doing so may affect compliance with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level requirements. Operation on Public Lands in the U.S.A. Your Polaris vehicle has a spark arrestor that was tested and qualified to be in accordance with the USFS standard 5100-1c.
MAINTENANCE Periodic Maintenance Chart Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment and lubrication of important components are explained in the periodic maintenance chart. Inspect, clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement parts, use genuine Polaris parts available from your Polaris dealer. Record maintenance and service in the Maintenance Log beginning on page 134.
MAINTENANCE Periodic Maintenance Chart WARNING Improperly performing the procedures marked with a could result in component failure and cause an accident, which may result in serious injury or death. Always have an authorized Polaris dealer perform these services. Maintenance Chart Key X Perform these operations more often for vehicles subjected to severe use. E Emission-related service (Failure to conduct this maintenance will not void the emissions warranty but may affect emissions.
MAINTENANCE Periodic Maintenance Chart Item Maintenance Interval Hours Calendar X Air filter, E main element X Brake pad wear Remarks (whichever comes first) Miles (Km) - Weekly - Inspect; replace as needed 10 H Monthly 60 (100) Inspect periodically 20 H 1M 125 (200) Perform a break-in oil change Q X Engine oil change (break-in) Battery 20 H Monthly 125 (200) Check terminals; clean; test Q ADC fluid 25 H - - Change fluid if extreme use conditions (see page 80) X Front gearcase (
MAINTENANCE Periodic Maintenance Chart Item Maintenance Interval Remarks (whichever comes first) Hours Calendar X Engine oil change 100 H X Oil filter change Q Valve clearance Fuel system Miles (Km) 6M 620 (1000) Perform a break-in oil change at one month 100 H 6M 620 (1000) Replace with oil change 100 H 12 M 620 (1000) Inspect; adjust 100 H 12 M 620 (1000) Check for leaks at tank cap, lines, filter, pump; replace lines every two years X Radiator (if applicable) 100 H 12 M 620 (1000)
MAINTENANCE Lubrication Recommendations Check and lubricate all components at the intervals outlined in the Periodic Maintenance Chart beginning on page 67. Items not listed in the chart should be lubricated at the General Lubrication interval. The a-arms and lower control arms are lubricated at the factory, and no additional lubrication will be needed. However, if these components are subjected to severe use, grease zerks have been provided for additional lubrication at the user's discretion.
MAINTENANCE Engine Oil Oil Recommendations Polaris recommends the use of Polaris PS-4 PLUS Performance Synthetic 2W-50 4-cycle oil or a similar oil for this engine. Oil may need to be changed more frequently if Polaris oil is not used. Always use 2W-50 oil. Follow the manufacturer's recommendations for ambient temperature operation. See page 124 for the part numbers of Polaris products. NOTICE: Mixing brands or using a non-recommended oil may cause serious engine damage. Always use the recommended oil.
MAINTENANCE Engine Oil Oil and Filter Change Always change the oil and filter at the intervals outlined in the Periodic Maintenance Chart beginning on page 67. Always change the oil filter whenever changing oil. 1. Position the vehicle on a level surface. 2. Start the engine. Drain Plug Location Allow it to warm up at idle for two to three minutes. Stop the engine. 3. Clean the area around the drain plug. 4. Place a drain pan to front under the crankcase. 5. Remove the drain plug.
MAINTENANCE Engine Oil Oil and Filter Change 10. Lubricate the o-ring on the new filter with a film of fresh engine oil. Check to make sure the o-ring is in good condition. 11. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface, then turn it an additional 1/2 turn. 12. Remove the dipstick. 13. Add two quarts (1.9 l) of recommended oil. 14. Place the transmission in park. 15. Lock the parking brake. 16. Start the engine.
MAINTENANCE Transmission Oil Always check and change the transmission oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 67. Maintain the oil level at the bottom Fill Plug of the fill plug hole. The fill plug is located on the right side of the ATV behind the footwell. The drain plug is located on the bottom left side of the gearcase. We recommend the use of Polaris Fill Level Drain Plug Premium AGL Synthetic Gearcase Lubricant.
MAINTENANCE Front Gearcase (Demand Drive) Fluid Always check and change the demand drive fluid at the intervals outlined in the Periodic Maintenance Chart beginning on page 67. We recommend the use of Polaris Demand Drive Plus Fluid. Use of other fluids may result in improper operation of components. See page 124 for the part numbers of Polaris products. Maintain the fluid level at the bottom of the fill hole threads. See below for capacity. Demand Drive Capacities Demand Drive with ADC 9.3 oz.
MAINTENANCE Front Gearcase (Demand Drive) Fluid Fluid Change 1. 2. 3. 4. 5. 6. 7. 8. Position the vehicle on a level surface. Remove the fill plug. Place a drain pan under the demand drive unit. Remove the drain plug. Allow the fluid to drain completely. Clean and reinstall the drain plug. Torque to 11 ft. lbs. (15 Nm). Add the recommended fluid. Reinstall the fill plug. Torque to 8-10 ft. lbs. (11-14 Nm). Check for leaks. Dispose of used fluid properly.
MAINTENANCE Rear Gearcase Oil Always check and change the rear gearcase oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 67. Maintain the fluid level at the bottom of the fill hole threads. The oil capacity is 5 oz. (150 ml). Do not overfill. Fill Plug The fill plug is located on the rear of the gearcase. The drain plug is located Drain Plug on the bottom of the gearcase. We recommend the use of Polaris ATV Angle Drive Fluid (or GL5 8090 weight gear lube).
MAINTENANCE Middle Gearcase Oil Always check and change the middle gearcase oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 67. We recommend the use of Polaris ATV Angle Drive Fluid (or GL5 80-90 weight gear lube). See page 124 for the part numbers of Polaris products. The middle gearcase fill plug is located on the side of the gearcase. Maintain the oil level even with the bottom thread of the fill plug hole. Drain Plug Check/Fill Plug Oil Check 1. 2. 3. 4.
MAINTENANCE Active Descent Control (ADC) Fluid If your vehicle is equipped with Active Descent Control, there are two fluid levels that must be maintained (demand drive fluid and ADC fluid). See page 76 for demand drive fluid maintenance. Check and change the ADC fluid level at the intervals outlined in the Periodic Maintenance Chart beginning on page 67. Maintain the fluid level between the minimum and maximum marks on the reservoir. We recommend the use of Polaris Demand Drive Plus Fluid.
MAINTENANCE Active Descent Control (ADC) Fluid Fluid Change 1. Position the vehicle on a level surface. Before performing the fluid change, allow the vehicle to sit for at least 30 minutes. 2. Thoroughly clean the areas around and on the ADC reservoir and bleeder valves (one on each side of the differential). 3. Remove the reservoir cap and diaphragm assembly. Use a shop towel or suction tool to remove debris from the fluid and reservoir.
MAINTENANCE Cooling System The engine coolant level is controlled, or maintained, by the recovery system. The recovery system components are the recovery bottle, the radiator filler neck, the radiator pressure cap and the connecting hose. As coolant operating temperature increases, the expanding (heated) excess coolant is forced out of the engine, past the pressure cap, and into the recovery bottle.
MAINTENANCE Cooling System Radiator Coolant To ensure that the coolant maintains its ability to protect the engine, Polaris recommends that you drain the system completely every two years and add a fresh mixture of antifreeze and water. Replace the coolant any time the cooling system has been drained for maintenance or repair. If the recovery bottle has run dry, check the level in the radiator. Add coolant as needed. CAUTION! Escaping steam can cause burns.
MAINTENANCE Brakes Front/Rear/Middle Brakes The front, rear and middle brakes are hydraulic disc brakes. These brakes are self-adjusting. Under normal operation, the diaphragm extends into the reservoir as fluid level drops. If the fluid level is low and the diaphragm is not extended, a leak is likely and the diaphragm should be replaced. To ensure proper diaphragm operation, always fill the reservoir as needed whenever the cover is loosened or removed. Do not overfill.
MAINTENANCE Toe Alignment Use the following procedure to check the toe alignment of the vehicle. The recommended toe alignment is 1/8" to 1/4" (3-6 mm) toe out. WARNING! Severe injury or death can result from improper toe alignment and adjustment. Do not attempt to adjust tie rod alignment. All tie rod adjustments should be performed by an authorized Polaris dealer. 1. Position the vehicle on a level surface. 2. Place the handlebars in a Stand straight-ahead position. 3.
MAINTENANCE Steering Assembly The steering assembly of the vehicle should be checked periodically for loose nuts and bolts. If loose nuts and bolts are found, see your Polaris dealer for service before operating the vehicle. Side Panel Removal 1. Remove the seat. 2. Grasp the rear of the side panel near the rear cab. With a firm motion, pull the panel outward to disengage the side panel from the grommet. Pull the panel downward and rearward to remove it. 3.
MAINTENANCE Tires WARNING Operating your vehicle with worn tires, improperly inflated tires, non-standard tires or improperly installed tires will affect vehicle handling and could cause an accident resulting in serious injury or death. Always follow all tire maintenance procedures as outlined in this manual and on the labels on the vehicle. Always use original equipment size and type when replacing tires.
MAINTENANCE Tires Wheel Installation 1. Place the transmission in park. 2. Lock the parking brake. 3. Place the wheel on the hub with the valve stem toward the outside and rotation arrows on the tire pointing toward forward rotation. 4. Install the wheel nuts and finger-tighten them. 5. Lower the vehicle to the ground. 6. Torque the wheel nuts to specification. WARNING! Loose nuts could cause a tire to come off during operation, which could result in an accident or overturn.
MAINTENANCE Air Filter 1. Remove the seat. 2. Release the air box cover clips, and remove the air box cover. 3. Loosen the clamp and remove the filter. 4. Remove the fabric type pre-filter from the main filter. Wash the pre-filter in soapy water, then rinse and let dry. 5. Reinstall the pre-filter over the main filter. Install a new main filter if needed. 6. Reinstall the filter into the air box and tighten the clamp. Do not over-tighten the clamp, as filter damage could occur. 7.
MAINTENANCE Fuse Replacement Fuse Feature Supported 5A Speedometer 15A Electronic Fuel Injection 20A (Main Fuse) Ignition, Lighting 20A Accessories, 12V Power Receptacle If the engine stops or will not start, or if you experience other electrical failures, a fuse may need replacement. Locate and correct any short circuits that may have caused the blown fuse, then replace the fuse. Spare fuses are provided in a compartment on the top of the access door. 1.
MAINTENANCE Lights Poor lighting can result in reduced visibility when driving. Headlight and taillight lenses become dirty during normal operation. Clean lights frequently and replace burned out lamps promptly. Always make sure lights are adjusted properly for best visibility. Upper Headlight Lamp Replacement When servicing a halogen lamp, don't touch the lamp with bare fingers. Oil from your skin leaves a residue, causing a hot spot that will shorten the life of the lamp. 1.
MAINTENANCE Lights High Beam Adjustment The headlight beam can be adjusted slightly upward or downward. Use the following procedure to make the adjustment. 1. Position the vehicle on a level surface with the headlight approximately 25 ft. (7.6 m) from a wall. Place the transmission in park. 25 ft. (7.6 m) 2" (5 cm) 2. Measure the distance from the floor to the center of the headlight and make a mark on the wall at the same height. 3. Start the engine. Turn the headlight switch to high beam. 4.
MAINTENANCE Lights Low Beam Adjustment The low beam can be adjusted slightly upward or downward. 1. Loosen the phillips screw located at the rear of the headlamp. 2. Tilt the headlamp upward or downward. 3. Tighten the screw.
MAINTENANCE Lights Headlight Housing Replacement 1. Remove the two screws on the lower front corners of the headlight pod. 2. Lift the pod slightly while depressing the tabs at the rear of the pod. 3. Lift the pod cover and disconnect the speedometer harnesses from the speedometer. 4. Unplug the headlamp from the wiring harness. 5. Use a small screwdriver to remove the o-rings from the headlight mounting tabs. 6. Pull the headlight housing up to release it from the locking tabs. 7.
MAINTENANCE Lights Lower Headlamp Replacement 1. Turn the back of the headlight harness counter-clockwise and pull the harness assembly away from the headlight assembly. 2. Remove the headlamp and install the new headlamp. 3. Reinstall the harness assembly into the headlight assembly. 4. Turn the headlight harness clockwise to secure the headlamp. Harness Taillight/Brakelight Lamp Replacement 1. Remove the taillight lens cover mounting screws. Remove the lens cover and gasket and set aside for reassembly.
MAINTENANCE Spark Plugs Spark Plug Recommendations Refer to the specifications section beginning on page 122 for the recommended spark plug type and gap for your vehicle. Torque spark plugs to specification. NOTICE: Using non-recommended spark plugs can result in serious engine damage. Always use Polaris-recommended spark plugs. Plug Condition Torque Specification New Spark Plug 9-11 ft. lbs. (12-15 Nm) Previously Installed Spark Plug 17-20 ft. lbs.
MAINTENANCE Spark Plugs Spark Plug Inspection Normal Spark Plug The normal insulator tip is gray, tan or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indicates the proper type and heat range for the engine and the service. The tip should not be flaky and white. A white insulator tip indicates overheating, caused by use of an improper spark plug or incorrect fuel. Wet Fouled Spark Plug The wet fouled insulator tip is black.
MAINTENANCE Vehicle Immersion If your vehicle becomes immersed, major engine damage can result if the machine is not thoroughly inspected. Take the vehicle to your dealer before starting the engine. If it's impossible to take your vehicle to a dealer before starting it, follow the steps outlined below. 1. Move the vehicle to dry land or at the very least, to water below the footrests. 2. Check the air box. If water is present, dry the air box and replace the filter with a new filter. 3.
MAINTENANCE Spark Arrestor WARNING Failure to heed the following warnings while servicing the spark arrestor could result in serious injury or death. Never run the engine in an enclosed area. Remove any combustible materials from the area. Wear eye protection and leather work gloves. Do not stand behind or in front of the vehicle while purging. Never go under the vehicle while it's inclined. The exhaust system can get extremely hot. Do not perform service on the spark arrestor while the system is hot.
MAINTENANCE PVT System WARNING Failure to comply with the instructions in this warning can result in severe injury or death. Do not modify any component of the PVT system. Doing so may reduce its strength so that a failure may occur at a high speed. The PVT system has been precision balanced. Any modification will cause the system to be out of balance, creating vibration and additional loads on components. The PVT system rotates at high speeds, creating large amounts of force on clutch components.
MAINTENANCE PVT System The basic operation of the Polaris PVT system is dependent on engine speed and vehicle torque requirements. As engine speed increases, the force exerted on the movable drive sheave by the flyweights also increases. This, in turn, increases the amount of pinch applied to the drive belt. Similarly, if the engine speed decreases, the amount of centrifugal force decreases, reducing the amount of belt pinch. The approximate gear ratio difference between high and low range is 1:2.25.
MAINTENANCE PVT System When To Use Low Range and High Range Condition Operating at speeds less than 7 MPH (11 km/h) Range to Use Low Towing heavy loads Low Operating in rough terrain (swamps, mountains, etc.) Low Operating at speeds greater than 7 MPH (11 km/h) High PVT Drying There may be some instances when water is accidently ingested into the PVT system. Use the following instructions to dry it out before operating. 1. Position the vehicle on a level surface. 2. Remove the drain plug.
MAINTENANCE Battery WARNING Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. WARNING Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with skin, eyes or clothing. Antidote: External: Flush with water.
MAINTENANCE Battery Battery Removal 1. 2. 3. 4. 5. 6. Remove the seat. Disconnect the battery hold-down strap. On conventional batteries, remove the battery vent tube. Disconnect the black (negative) battery cable first. Disconnect the red (positive) battery cable last. Lift the battery out of the vehicle. Be careful not to tip a conventional battery sideways, which could spill electrolyte.
MAINTENANCE Battery Battery Installation Using a new battery that has not been fully charged can damage the battery and result in a shorter life. It can also hinder vehicle performance. Follow the battery charging instructions on page 107 before installing the battery. 1. Ensure that the battery is fully charged. 2. Place the battery in the battery holder. 3. With conventional batteries, install the battery vent tube (sealed batteries do not have a vent tube).
MAINTENANCE Battery Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully charged, and store it out of the sun in a cool, dry place. Check battery voltage each month during storage and recharge as needed to maintain a full charge. Polaris recommends maintaining battery charge by using a Polaris Battery Tender charger or by charging about once a month to make up for normal self-discharge.
MAINTENANCE Battery Battery Charging (Conventional Battery) 1. Remove the battery from the vehicle to prevent damage from leaking or spilled electrolyte during charging. See page 104. 2. Charge the battery with a charging output no larger than 1/10 of the battery’s amp/hr rating. Charge as needed to raise the specific gravity to 1.270 or greater. 3. Reinstall the battery. See page 105. Make sure the positive terminal is toward the front of the vehicle.
MAINTENANCE Battery Battery Charging (Sealed Battery) Always verify battery condition before and 1-2 hours after the end of charging. Charge Time State of Charge Voltage Action (Using constant current charger @ standard amps specified on top of battery) 100% 12.8-13.0 volts None required 75%-100% 12.5-12.8 volts 50%-75% 25%-50% 12.0-12.5 volts 11.5-12.0 volts None, check at 3 mos.
MAINTENANCE Cleaning and Storage Washing the Vehicle Keeping your Polaris vehicle clean will not only improve its appearance but it can also extend the life of various components. NOTICE: High water pressure may damage components. Polaris recommends washing the vehicle by hand or with a garden hose, using mild soap. Certain products, including insect repellents and chemicals, will damage plastic surfaces. Do not allow these types of products to contact the vehicle.
MAINTENANCE Cleaning and Storage Washing the Vehicle If a high pressure water system is used for cleaning (not recommended), exercise extreme caution. The water may damage components and could remove paint and decals.
MAINTENANCE Cleaning and Storage Chrome Wheel Care (if equipped) Proper maintenance will protect chrome wheels from corrosion, preserve wheel life and ensure a "like new" appearance for many years. Chrome wheels exposed to road salt (or salt in the air in coastal areas) are more susceptible to corrosion if not properly cleaned. Clean chrome wheels more often if they're exposed to salt or other corrosive elements. 1. Wash chrome wheels frequently. Use a mild detergent.
MAINTENANCE Cleaning and Storage Storage Tips NOTICE: Starting the engine during the storage period will disturb the protective film created by fogging and damage could occur. Never start the engine during the storage period. Clean the Exterior Make any necessary repairs and then clean the vehicle as recommended. See page 109. Stabilize the Fuel 1. Fill the fuel tank. 2. Add Polaris Carbon Clean Fuel Treatment or Polaris Fuel Stabilizer. Follow the instructions on the container for the recommended amount.
MAINTENANCE Cleaning and Storage Storage Tips Fluid Levels Inspect the following fluid levels. Change fluids as recommended in the Periodic Maintenance Chart beginning on page 67. • Demand drive unit (front gearcase) • ADC fluid (ADC models) (change every two years) • Rear gearcase • Middle gearcase • Transmission • Brake fluid (change every two years and any time the fluid looks dark or contaminated) • Coolant (test strength) Fog the Engine 1.
MAINTENANCE Cleaning and Storage Storage Tips Inspect and Lubricate Inspect all cables and lubricate all areas of the vehicle as recommended in the Periodic Maintenance Chart beginning on page 67. Battery Maintenance Remove the battery and recharge it as outlined on page 107. Store the battery in a cool, dry place. Storage Area/Covers Set the tire pressure and safely support the vehicle with the tires slightly off the ground. Be sure the storage area is well ventilated.
MAINTENANCE Transporting the Vehicle Follow these procedures when transporting the vehicle. 1. Stop the engine. 2. Place the transmission in park. 3. Lock the parking brake. 4. Secure the fuel cap, oil cap and seat. 5. Always tie the frame of the vehicle to the transporting unit securely with suitable straps or rope. Do not attach tie straps to the front A-arm bolt pockets, racks or handlebars. 6. Remove the key to prevent loss during transporting.
ADJUSTMENTS Camber and Caster The camber and caster are non-adjustable. Rear Springs The rear shock absorber springs are adjusted by rotating the adjusters either clockwise or counter-clockwise to increase or decrease spring tension. Always adjust all rear springs to equal settings. Accessory springs are available through your Polaris dealer. Adjuster Handlebars The handlebars can be adjusted for rider preference.
ADJUSTMENTS Throttle Body/Idle RPM Idle RPM is preset by the manufacturer. If the engine idle speed is not satisfactory, please see your Polaris dealer for adjustment. Throttle Cable Freeplay Adjust throttle cable freeplay at the handlebar. 1. Locate the throttle cable adjuster at the handlebar. 2. Squeeze the end of the rubber boot and slide it far enough to expose the end of the inline cable adjuster. 3. Loosen the adjuster lock nut. 4. Rotate the boot to turn the adjuster until 1/16" to 1/8" (1.
TROUBLESHOOTING Drive Belt Wear/Burn Possible Cause Driving onto a pickup or tall trailer in high range Starting out going up a steep incline Driving at low RPM or ground speed (3-7 MPH) Insufficient warm-up at low ambient temperatures Solution Use low range during loading. Use low range or turn around using the K-turn (see page 58). Drive at a higher speed or use low range more frequently. See page 102. Warm the engine at least 5 minutes.
TROUBLESHOOTING Engine Doesn't Turn Over Possible Cause Low battery voltage Loose battery connections Loose solenoid connections Solution Recharge the battery to 12.
TROUBLESHOOTING Engine Pings or Knocks Possible Cause Poor quality or low octane fuel Incorrect ignition timing Incorrect spark plug gap or heat range Solution Replace with recommended fuel See your dealer Set gap to specs or replace plugs Engine Runs Irregularly, Stalls or Misfires Possible Cause Fouled or defective spark plugs Worn or defective spark plug wires Incorrect spark plug gap or heat range Loose ignition connections Water present in fuel Low battery voltage Kinked or plugged fuel tank vent lin
TROUBLESHOOTING Engine Stops or Loses Power Possible Cause Out of fuel Kinked or plugged fuel vent line Water is present in fuel Fouled or defective spark plugs Worn or defective spark plug wires Incorrect spark plug gap or heat range Loose ignition connections Low battery voltage Incorrect fuel Clogged air filter Reverse speed limiter malfunction Electronic throttle control malfunction Other mechanical failure Overheated engine Solution Refuel, cycle key to ON position three times for 5 seconds each, then
SPECIFICATIONS SPORTSMAN BIG BOSS 6X6 800 EFI Maximum Weight Capacity Fuel Capacity Engine Oil Capacity Coolant Capacity Demand Drive Fluid Capacity Rear Gearcase Oil Capacity Mid Gearcase Oil Capacity Transmission Oil Capacity Front Rack/Storage Box Capacity Cargo Box Capacity Receiver Hitch Tongue Capacity Hitch Towing Rating Unbraked Trailer Towing Capacity* Overall Length Overall Width Overall Height Wheelbase Ground Clearance Dry Weight Minimum Turning Radius Engine Displacement Bore x Stroke Alternato
SPECIFICATIONS SPORTSMAN BIG BOSS 6X6 800 EFI Transmission Gear Reduction, Low Gear Reduction, Reverse Gear Reduction, High Drive Ratio, Front Drive Ratio, Final Tires/Pressure, Front Tires/Pressure, Center Tires/Pressure, Rear Brakes, Front Brakes, Rear Brakes, Auxiliary Brake, Parking Headlight Taillights Brake Light Instrument Cluster Automatic PVT with E-Z Shift H/L/N/R/P 7.49:1 5.11:1 3.05:1 3.82:1 3.10:1 25x8-12 / 7 psi (48.3 kPa) 25x11-12 / 10 psi (68.9 kPa) 25x11-12 / 10 psi (68.
POLARIS PRODUCTS Part Number 2870791 2876244 2876245 2873602 2873603 2877922 2877923 2871653 2872276 2870465 2871323 2871534 2871312 2871322 2871423 2871460 2871515 2871551 2871329 2871326 2870652 2872189 2871956 2859044 124 Description Engine Lubricant Fogging Oil (12 oz. Aerosol) PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (qt.) PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (gal.) Gearcase / Transmission Lubricants Premium AGL Synthetic Gearcase Lubricant (qt./.
DECLARATION OF CONFORMITY Polaris Industries Inc., 2100 Hwy 55, Medina, MN 55340 U.S.A. Telephone 763-542-0500 We, Polaris Industries Inc., declare that the vehicles listed below conform to the essential health and safety requirements applicable to off-road all-terrain vehicles. APPLICABLE EUROPEAN DIRECTIVES 98/37/EC as amended (Machinery Directive) TEST / EVALUATION METHODS EN 1050 hazard analysis CD 77/311/EEC driver-perceived noise level CISPR 12:2001 EN 55012:2002 CAN/CSA-C108.
WARRANTY LIMITED WARRANTY Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, gives a SIX MONTH LIMITED WARRANTY on all components of the Polaris Light Utility Vehicle against defects in material or workmanship. Polaris also gives a one year limited warranty on the final drive chain (if equipped) for failure due to defects. This warranty covers the parts and labor charges for repair or replacement of defective parts which are covered by this warranty. This warranty begins on the date of purchase.
WARRANTY WARRANTY COVERAGE AND EXCLUSIONS: LIMITATIONS OF WARRANTIES AND REMEDIES The Polaris limited warranty excludes any failures that are not caused by a defect in material or workmanship. This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling.
WARRANTY LIMITATIONS OF WARRANTIES AND REMEDIES This warranty also excludes failures resulting from improper lubrication; improper engine timing; improper fuel; surface imperfections caused by external stress, heat, cold or contamination; operator error or abuse; improper component alignment, tension, adjustment or altitude compensation; failure due to snow, water, dirt or other foreign substance ingestion/contamination; improper maintenance; modified components; use of aftermarket components resulting in f
WARRANTY ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you if inconsistent with controlling state law.
WARRANTY Exported Vehicles EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO WARRANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCATION. This policy does not apply to vehicles that have received authorization for export from Polaris Industries. Dealers may not give authorization for export. You should consult an authorized dealer to determine this vehicle's warranty or service bulletin coverage if you have any questions.
WARRANTY Exported Vehicles How to Get Service If Purchased From A Private Party: If you purchase a Polaris product from a private citizen, to be kept and used outside of the country in which the vehicle was originally purchased, all warranty coverage will be denied. Notice If your vehicle is registered outside of the country where it was purchased, and you have not followed the procedure set out above, your vehicle will no longer be eligible for warranty or service bulletin coverage of any kind.
WARRANTY U.S.A. EPA Emissions Limited Warranty This emissions limited warranty is in addition to the Polaris standard limited warranty for your vehicle. Polaris Industries Inc. warrants that at the time it is first purchased, this emissions-certified vehicle is designed, built and equipped so it conforms with applicable U.S. Environmental Protection Agency emission regulations.
WARRANTY U.S.A. EPA Emissions Limited Warranty The exclusive remedy for breach of this limited warranty shall be, at the exclusive option of Polaris, repair or replacement of any defective materials, components or products. THE REMEDIES SET FORTH IN THIS LIMITED WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY.
MAINTENANCE LOG Present this section of your manual to your dealer each time your vehicle is serviced. This will provide you and future owners with an accurate log of maintenance and services performed.
MAINTENANCE LOG DATE MILES (KM) OR HOURS TECHNICIAN SERVICE PERFORMED / COMMENTS 135
MAINTENANCE LOG DATE 136 MILES (KM) OR HOURS TECHNICIAN SERVICE PERFORMED / COMMENTS
INDEX 0-9 C 4X4 (AWD) Switch . . . . . . . . . . 26, 34 Clothing . . . . . . . . . . . . . . . . . . . . . . . 9 Clutching. . . . . . . . . . . . . . . . . . . . . 123 Codes . . . . . . . . . . . . . . . . . . . . . 43-45 Cold Weather Operation . . . . . . . . . . 51 Consumer Product Safety . . . . . . . . . . 7 Coolant Bottle . . . . . . . . . . . . . . . . . . 82 Coolant, Radiator . . . . . . . . . . . . . . . 83 Cooling System. . . . . . . . . . . . . . 82-83 Corrosion Removal, Chrome . . . . .
INDEX F L Fluid ADC. . . . . . . . . . . . . . . . . . . 80-81 Brake . . . . . . . . . . . . . . . . . . . . 31 Demand Drive . . . . . . . . . . . 76-77 Fluid Change ADC. . . . . . . . . . . . . . . . . . . . . 81 Demand Drive . . . . . . . . . . . . . 77 Footwell Removal . . . . . . . . . . . . . . 86 Front Gearcase (Demand Drive) . 76-77 Fuel Safety . . . . . . . . . . . . . . . . . . . . 11 Fuel Tank Cap . . . . . . . . . . . . . . . . . 33 Fuse Replacement . . . . . . . . . . . . . . 90 Lights . . .
INDEX P S Parking Brake . . . . . . . . . . . . . . . . . . 32 Parking on an Incline . . . . . . . . . . . . 65 Periodic Maintenance Chart . . . . 67-70 Polaris Product List. . . . . . . . . . . . . 124 Polishing the Vehicle . . . . . . . . . . . 110 Pre-Ride Checklist . . . . . . . . . . . . . . 48 PVT Break-In . . . . . . . . . . . . . . . . . . 47 PVT Drying. . . . . . . . . . . . . . . . . . . 102 PVT System . . . . . . . . . . . . . . 100-102 Switches AWD Switch. . . . . . . . . . . .
