User manual

Mounting and connection
Refer to the information in section „Preparation for mounting“!
Ensure that no existing cables or pipes (including water pipes) are damaged when drilling
mounting holes or securing screws.
2 x
• Remove the two side screws with a cross-head
screwdriver and remove the washers.
• Carefully pull the wall mount (6) out of the light.
• Remove the screw terminal by carefully pulling it out
of the wall mount.
10 mm
6 mm
• Remove the outer insulation on the wires to a maximum
length of about 16 mm. Strip the insulation on each of
the three wires on the mains cable to a length of about
6 mm. The protective earth cable (yellow and green)
should be at least 6 mm longer so that it remains the
last cable in the screw terminal in the event of a fault.
• Push the stripped mains cable through the rubber
gasket from the wall side.
• Usethe wallmountasatemplateto markthexing
points on the surface. Pay attention to the orientation
of the light housing. Use the correct sensor orientation
(vertical and lamp shade upwards).
• Secure the wall mount to a wall with two screws and, if
necessary, dowels. Depending on the surface, suitable
screws and dowels are required.
• Connect the 3 wires on the mains cable to the 3-pole
screw terminal (brown wire= L/phase, blue wire = N/
neutral wire, yellow/green wire = PE/earth wire/earth
symbol ).
• Also check the other screw connections on the screw
terminal (for the connection cables to the LED driver)
and tighten them if necessary.
2 x
• Place the screw terminal back on the retaining pins on
the wall mount intended for this purpose.
• Put the wall light on the wall mount and screw it in
place with the two screws and washers that you
unscrewed at the start.
Using the built-in plug socket
 Onlyusethesocketoncethelighthasbeenconnectedasdescribedabove.
• Openthecover(5).
• Inserttheplugfroma220-240V/ACdeviceintothelight'sbuilt-insocket(5).
Conguring the movement sensor (PIR)
Use a suitable cross-head screwdriver to turn the adjusting screws. Using excessive force when
setting the adjusting screws can cause damage to the light.
• Congurethesensitivityofthemovementsensor(2). The registering of a movement by the movement
sensordependsonthedistancefromthemovingobject.ThePIRdetectionangleis120°.Congurethe
reaction distance by turning the - SENS + (3) adjusting screw:
- Turn the - SENS + adjusting screw to the right to increase the reaction distance.
- Turn the - SENS + adjusting screw to the left to shorten the reaction distance.
• Congurethetimeafterwhichthelightturnsoffafterdetectingamovingobject.Thelightturnsoffaftera
shorterorlongertime.Youcanchooseatimebetween10secondsand4minutes.Conguretheswitch-off
time by turning the - TIME + (4) adjusting screw:
- Turn the - TIME + adjusting screw to the right to increase the switch-off time.
- Turn the - TIME + adjusting screw to the left to reduce the switch off time.
• When it is dark the light automatically switches on when an object (people, animals, vehicles, etc.) enters
thedetectionareacoveredbythePIRsensor'sinfraredraysormoveswithinthisarea.
• The light sensitivity cannot be adjusted.
Care and cleaning
• Turnoffmainsvoltagetothelight(ordisconnectitfromthemains)andletitcooldownsufciently.
• Always disconnect connected devices from the power supply before cleaning it.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may damage the
housing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product. To remove stubborn dirt, moisten the cloth slightly with water.
• Never direct a garden hose or pressure washer etc. at the product.
• Do not wear metallic or conductive jewellery such as necklaces, bracelets or rings when carrying out
maintenance work on the product (including cleaning).
Disposal
Electronic devices are recyclable waste and must not be placed in household waste. Always
dispose of the product according to the relevant statutory regulations.
Technical data
a) General information
Operatingvoltage ................................. 220–240 V/AC, 50 Hz
Power consumption .............................. 6.5 W
Protection rating ................................... IP44
Protection class .................................... I
Material ................................................. Stainless steel housing, plastic light head
Mounting location ................................. Indoors/outdoors
Illuminant .............................................. 30 LEDs
Colour temperature ............................... 3000 K (warm white)
Luminousux ....................................... 525 lm
PIR range ............................................. 4 - 7 m
PIR detection angle .............................. approx. 120° (horizontal and vertical)
Setting the time ..................................... 10 seconds to 4 minutes
Earthing contact socket-outlet .............. 1
Operating/storageconditions ................ -20 to +40 °C
Dimensions (Ø x H) .............................. 7.6 x 29.8 cm
Weight ..................................................705 g
b) Integrated socket
Nominal voltage .................................... 220–240 V/AC, 50 Hz
Rated current ........................................ 16 A
Power ................................................... Max. 3840 W
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,
Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproductionbyanymethod,e.g.photocopy,microlming,orthecaptureinelectronicdataprocessingsystemsrequire
thepriorwrittenapprovalbytheeditor.Reprinting,alsoinpart,isprohibited.Theoperatinginstructionsreectthecurrent
technicalspecicationsattimeofprint.
© Copyright 2017 by CEI Conrad Electronic International (HK) Limited *1581289_V1_1217_02_LS_m_EN
Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau