User manual

ManualsBrandsPOLARLITE ManualsChristmas WorldLED projector Snowflakes White LED LP-100 Black (matt)

Product overview

31 cm

9.8 cm

Operation

Do not install or operate the product under water.

Make sure the cable hangs loosely and is not overly

tensioned. Failure to heed this warning may cause the

cables to tear.

Do not connect the product to the power supply while it

is still in the packaging. Uncoil the power cable fully.

Do not hang any objects from the product and do not

cover the product.

When inserting the ground spike into the soil, do not

use any tools (e.g. hammers), as such would damage the

product.

Check all screw connections from time to time. Screw

connections may loosen over time due to adjusting and

moving the product.

The LEDs are neither dimmable nor replaceable.

1. Uncoil the power cable fully.

2. Loosen the screw by turning it anticlockwise, and remove the

spring washer and ﬂat washer from the ground spike using

the spanner provided.

3. Attach the LED projector to the ground spike using the

screw, spring washer and ﬂat washer.

4. Connect the plug of the power cable to the socket on the

transformer. It is only possible to connect in one way. Secure

the connection by turning the plug’s screw cap onto the

transformer’s thread.

5. Choose a suitable location to set up the device with soft

ground. Stony ground will damage the ground spike.

Carefully insert the LED projector including the ground spike

all the way into the soil.

6. Loosen the bracket screws. Adjust the angle of the projector

as desired and then retighten the screws.

7. Connect the transformer to a power outlet. The projector is

now switched on and starts rotating.

The product has no power switch and is always on as long as

it is connected to the power supply. Disconnect the power

supply in order to switch the LED projector o.

Care and cleaning

• Disconnect the transformer from the mains socket and let the

LED projector cool down suciently before cleaning.

• Do not use any abrasive or chemical cleaners. To clean, use a

clean, dry, lint-free cloth. For stubborn dirt, slightly dampen the

cloth with water.

• Allow the product to dry completely before continued use.

Disposal

Electronic devices are recyclable waste and must not be

placed in household waste. At the end of its service life,

dispose of the product in accordance with applicable

regulatory guidelines.

You thus fulﬁl your statutory obligations and contribute

to the protection of the environment.

Technical data

a) LED projector

Operating voltage ............................... 7 – 14 V/DC

Power consumption ........................... 5.5 W

Protection type .................................... IP44

Number of lights .................................. 4

Luminous color ..................................... cool white

Cable length........................................... 4.7 m

Distance to illuminated area .......... 5 m

Operating conditions ........................ -20 to +40 °C, 0 – 100 % RH

Storage conditions ............................. -20 to +40 °C, 0 – 100 % RH

Dimensions (Ø x L)............................. 9.8 x 9.8 cm (projector)

4.3 x 21.3 cm (spike)

Weight ...................................................... 499 g

b) Transformer

Input voltage ......................................... 100 – 240 V/AC, 50/60 Hz

Output voltage ..................................... 7 – 14 V/DC

Output current ..................................... 300 mA

Output power ....................................... max. 4.2 W

Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau 1675053_V2_0718_02_mxs_m_en

These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,

Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.

Reproduction by any method (e.g. photocopying, microﬁlming, or the capture in electronic data processing

systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited. These operating

instructions reﬂect the current technical speciﬁcations at the time of printing.