User manual
Product overview
30 cm
11.8 cm
Operation
Do not install or operate the product under water.
Make sure the cable hangs loosely and is not overly
tensioned. Failure to heed this warning may cause the
cables to tear.
Do not connect the product to the power supply while it
is still in the packaging. Uncoil the power cable fully.
Do not hang any objects from the product and do not
cover the product.
When inserting the ground spike into the soil, do not
use any tools (e.g. hammers), as such would damage the
product.
Check all screw connections from time to time. Screw
connections may loosen over time due to adjusting and
moving the product.
The LEDs are neither dimmable nor replaceable.
1. Uncoil the power cable fully.
2. Loosen the screw by turning it anticlockwise, and remove the
spring washer and flat washer from the ground spike using
the spanner provided.
3. Attach the LED projector to the ground spike using the
screw, spring washer and flat washer.
4. Connect the plug of the power cable to the socket on the
transformer. It is only possible to connect in one way. Secure
the connection by turning the plug’s screw cap onto the
transformer’s thread.
5. Choose a suitable location to set up the device with soft
ground. Stony ground will damage the ground spike.
Carefully insert the LED projector including the ground spike
all the way into the soil.
6. Loosen the bracket screws. Adjust the angle of the projector
as desired and then retighten the screws.
7. Connect the transformer to a power outlet. The projector is
now switched on and starts rotating.
The product has no power switch and is always on as long as
it is connected to the power supply. Disconnect the power
supply in order to switch the LED projector o.
Within 10 minutes after switching on the LED projector,
condensation might form inside the projector lens. This
condensation should dissipate within 30 minutes of
operation.
Pattern lens installation and replacement
For convenience, one pattern slide is assembled inside the
projector at the factory.
1. Unscrew and remove the two screws holding the pattern lens
inside the projector.
2. Remove the pattern lens already installed inside the projector.
3. Reinsert dierent pattern lens into the projector. In doing so,
be careful to orient the pattern lens correctly: the arrow on
the frame must face to the front of the projector.
4. Lock in place using the two screws.
The pattern slide may slightly fade over time due to light
exposure.
Care and cleaning
• Disconnect the transformer from the mains socket and let the
LED projector cool down suciently before cleaning.
• Do not use any abrasive or chemical cleaners. To clean, use a
clean, dry, lint-free cloth. For stubborn dirt, slightly dampen the
cloth with water.
• Allow the product to dry completely before continued use.
Disposal
Electronic devices are recyclable waste and must not be
placed in household waste. At the end of its service life,
dispose of the product in accordance with applicable
regulatory guidelines.
You thus fulfil your statutory obligations and contribute
to the protection of the environment.
Technical data
a) LED projector
Operating voltage ............................... 14 V/DC
Power consumption ........................... 8 W
Protection type .................................... IP44
Number of lights .................................. 4
Luminous color ..................................... cool white
Cable length........................................... 1 m
Distance to illuminated area .......... 3 – 5 m
Operating conditions ........................ -20 to +45 °C, 0 – 100 % RH
Storage conditions ............................. -20 to +70 °C, 0 – 100 % RH
Dimensions (L x W x H) ................... 11.8 x 8 x 13 cm (projector)
11.8 x 8 x 30 cm (total)
Weight ...................................................... 280 g
b) Transformer
Input voltage ......................................... 100 – 240 V/AC, 50/60 Hz
Output voltage ..................................... 14 V/DC
Output current ..................................... 500 mA
Output power ....................................... max. 7 W
Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau 1676601_V2_0718_02_mxs_m_en
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,
Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method (e.g. photocopying, microfilming, or the capture in electronic data processing
systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited. These operating
instructions reflect the current technical specifications at the time of printing.
© Copyright 2018 by CEI Conrad Electronic International (HK) Limited