7” Under-the-Counter LCD FCM-0700A Operating Manual
Table of Contents Table of Contents ----------------------------------------------------------- 2 Important Safety Instruction--------------------------------------------- 3 FCC Notice--------------------------------------------------------------------- 5 Characteristic Features --------------------------------------------------- 6 Front Panel -------------------------------------------------------------------- 7 Rear Panel and Display Panel------------------------------------------- 8 Remote Control ------
Important Safety Instruction CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.
Important Safety Instruction Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use near water. Clean only with dry cloth. Do not block any ventilation openings. Maintain well ventilated conditions around the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer’s instructions.
FCC Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Characteristic Features This product has incorporated LCD TV Functions display, TV receiver and radio function Receive TV signal clearly. in one system. It is designed for Search for TV channels automatically. convenient use in the kitchen; please Memorize the channels automatically. refer to page 21 for the installation Radio Functions instructions. Receive AM/FM signal clearly. Multiple Mode Search for radio stations automatically. TV mode Store radio stations easily.
Front Panel Front Panel Drawing 1. POWER button Press to access to or exit the STANDBY mode. 2. TV button Press to enter TV mode. Or under TV mode, press to display the current channel number on the display panel. 3. FM button Press to enter FM radio mode. 4. AM button Press to enter AM radio mode. 5. AV button Press to enter external AV input mode. 6. 16:9/4:3 button Press to shift the aspect radio between 16:9 and 4:3. 7. Remote Sensor Receives remote control signal for operation. 8.
Rear Panel and display panel 16. ► Press to select items in the setup menu. Or press to increase the volume. Or press to increase the value in the picture setup menu. 17. MENU button Press to enter the system setup menu. 18. ▼ Press to select items in the setup menu. Press to select the channels or radio stations backward under TV or radio mode. Press to adjust the value downward when setting the time on the display panel. 19. ◄ Press to select items in the setup menu. Or press to decrease the volume.
Remote Control Preparation Use Of Remote Control Refer to the drawing, and remove the Please directly point the r/c towards the main unit when operating. The r/c works properly in a distance below 7m and at empty battery receptacle. an angle of up to 60°to the front of the unit. No obstacles may stand in the way between r/c and infrared sensor. Insert the battery into the receptacle, please make sure the polarity matches the marks inside the component.
Remote Control Remote Control Drawing 1. POWER button Press to access to or exit from the STANDBY mode. 2. TV button Press to enter TV mode. 3. FM button Press to shift to FM signal input mode. 4. AM button Press to shift to AM signal input mode. 5. AV button Press to shift to external AV input mode. 6. MENU button Press to enter the system setup menu.
Remote Control 7. OK button Press to confirm selections. 8. Press to select menu items or settings. Press buttons to adjust volume. Or press to adjust value in the picture setup menu. Press buttons to select channels or radio stations forward and backward in TV or radio mode. Or press to adjust the value of time when setting time on the display panel. 9. TIME button Press it once to display the time on the display panel. In standby status, the time is still displayed on the display panel.
System Connections • Do not connect the power cord until all other connections have been made. • Each time you restart the unit, it remembers the last function used.
System Connections Connecting To Antenna Connect the supplied AM/FM antennas to listen to the radio. • In order to improve the signal, move AM loop antenna away from system and other equipment. • Extend FM antenna fully. • Keep the FM antenna as horizontal as possible after connection. • When connecting the supplied AM loop antenna, connect two black cords to AM and ground jacks as shown below.
System Connections Connecting To the Power Adapter This unit is powered via the switching power adapter (supplied). See the below figure for details: 1. Connect the AC adapter to jack marked with “DC 12V IN” on the rear panel of the unit. 2. Plug the two-prong end of the power cord to the grounded electrical socket. 3. When not using the unit, turn off the power of the unit first, and then unplug the power supply to prevent malfunctions.
Radio Function Radio Function Operation Press the AM or FM button on the remote control or front panel to enter AM or FM radio mode. Then press the SEEK+/- button for about 1.5 seconds on the remote control or front panel to start searching forward/backward from the current frequency. Press the SEEK+/- button again to stop searching. Radio frequency will be displayed on the display panel. The frequency range of FM is from 87.5MHz to 107.9MHz, frequency range of AM is from 520KHz to 1710KHz.
TV Function Basic Operation Connect the antenna to the antenna jack on the rear panel. After connecting the antenna, connect the power supply cord. If the player is in standby mode, press the POWER button on the front panel to turn on the power. Press the TV button on the remote control to shift to TV mode. Press the CHANNEL+/- buttons or buttons on the remote control, or use the number buttons directly, to select the desired channel.
TV Function Use the ▼, ▲ buttons to select the item you want to set. Use the ►, ◄ buttons to enter the item and to select. Press the ► button on the remote control to exit from the setup menu. Press the ◄ button on the remote control to return to the picture setup menu. Signal Use the ► direction button to select CATV TV signal input mode. Use the ◄ direction button to select AIR TV signal input mode. Channel Use the ►, ◄ buttons to change the channel.
TV Function The auto memory will take a few minutes. The unit will search channels from the lowest channel to the highest channel in the standard channel list. When tuning operations are complete the unit will exit and store the channels by sequence in the memory. During tuning, press the ◄ button to exit the auto memory. Use the CHANNEL +/- or ▼, ▲ direction buttons to select the desired channel from those in memory.
TV Function Power off To set the playback end time of the signal source use number buttons to input the desired time in sequence of hour, minute. Press the ►, ◄ direction buttons to shift between am and pm. When the playback of the signal source is over, the player will enter standby mode. Signal Use the ►, ◄ direction buttons to select CATV, AIR, FM or AM. Channel Use number buttons to input the desired TV channels.
AV Function AV Function The player has an additional AV input so it can function as a monitor for a DVD player, video cassette player, satellite receiver, video game, etc. When an AV source is connected, press the AV button on the remote control to enter external input AV mode.
Installing the Unit in Kitchen Installing the unit under a cabinet The player unit may be installed in the kitchen with or without the spacers. The suggested mounting position of the unit is under a wall cabinet. See drawings below: NOTE: The dimensions of the player: 355mm X 75mm x285 mm (W/H/D) There should be at least 35mm distance between the unit and the wall. Installing steps 1. Mark the position of the 4 holes by using the supplied template. Drill four 6.5 mm diameter holes.
Installing the Unit in Kitchen 2. If the cabinet door overhangs the shelf and obstructs the unit, adjust the unit or the shelf height for clearance. 3. Install the unit with the supplied mounting screws. 4. There should be at least 35mm distance between the unit and the wall. Quick hints • • Since the unit is rather heavy, be careful while doing the installation work.
Troubleshooting SYMPTOM CHECK ITEM There is no sound. Make sure system connection is correct. Make sure the player is not under muting mode. Press the MUTE button to turn on the speaker. Make sure the volume is adjusted to the lowest. Adjust the volume upward. There is no picture or the position of the picture is incorrect. Make sure the video type of the AV signal source TV is NTSC. Make sure system connection is correct. The remote control does not work.
Specifications LCD screen size 7 inches System Radio Frequency Range PLL AM 520~1710kHz FM 87.5~107.9MHz Power AC100V~ 240V, 50/60Hz Power Consumption <16W Dimension 355mm X 75mm x285 mm (W/H/D) Weight About 3.4kgs DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE For service, support and warranty information, visit www.polaroidelectronics.com or in the US call 1-866-289-5168, in Canada call 1-866-301-7922 and in Mexico call 01-800400-2443.
