5” LCD Television FLM-1514, FLM-1514B, FLM-153B, FLM-1517 Your LCD TV may look slightly different from the one pictured above.
Table Of Contents Important Safety Instructions--------------------------------------------------1 Product Features ---------------------------------------------------------3 Front Panel---------------------------------------------------------------------------4 Rear Panel----------------------------------------------------------------------------5 Remote Control---------------------------------------------------------------------6 System Connections----------------------------------------------------------
Important Safety Instructions The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Important Safety Instructions Note: 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use near water. Clean only with dry cloth. Do not block any ventilation openings. Maintain well ventilated conditions around the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer’s instructions. 8.
Product Features This product incorporates LCD display and TV receiver in one system. Multiple Mode Special Function Support sleep time setting function. Component mode VGA mode TV mode Composite mode S-VIDEO mode Multi-audio and Multi-video modes Support multi-audio and multi-video modes, provide more selecting. High Quality Property LCD (Liquid Crystal Display) Designed with 15" color TFT liquid crystal display clearly shows the data.
Front Panel 1. INPUT button Press to select the modes: Component, VGA, TV, Composite or S-VIDEO. 2. MENU button Press to enter or exit setup menu. 3. CH ▲/▼ button In the TV mode, press to select channels. In setup menu, the same function as ▲/▼ direction buttons. 4. VOL◄/► button In the TV mode, press to decrease or increase the volume. In setup menu, the same function as ◄/►direction buttons. 5. POWER button Press to enter or exit the standby mode. 6.
Rear Panel 5. VGA Input Jack Connected to the VGA output jack on a personal computer. 6. PC AUDIO Input Jack Connected to the PC audio output jack. 7. TV Signal Input Jack Connected for the external NTSC TV signal input. 1. Component Input / L/R Audio Input Jack Connected to the Component (YPbPr) input in Component mode. Connected to the L/R audio input in Component mode. 2. S-VIDEO Input Jacks 3. VIDEO/L/R Audio Input Jack Connected to the VIDEO input in Composite mode.
Remote Control Remote Control Drawing 1. INPUT button Press to select the modes: Component, VGA, TV, Composite or S-VIDEO. 2. 0~9 Number buttons Press to select numbers. 3. LAST button In the TV mode, press to return to the channel last viewed. 4. MUTE button Press to turn on or off the speaker output. 5. Direction buttons (▲▼◄►) In the setup menu, press the ▲▼button to select the desired item and press the ◄► button to adjust or set. 6. OK button Press to confirm your selection. 7.
Remote Control Preparation of Remote Control Using of Remote control Softly push the back cover to open the battery Point the remote control unit from no more than about 7m from the remote control sensor and within about 60 degrees of the front of the unit. compartment. Insert two batteries (1.5V, size AAA) into the compartment, please make sure the polarity matches the marks inside the compartment. Softly press the back cover to close it.
System Connections • Do not connect the power cord until all other connections have been made. • Ensure that you observe the color cord when connecting audio and video cables. Connecting to External AV Signal Source Use the audio and video cable to connect the AV input jacks on the rear panel of the unit to the external AV signal source. After connection, turn on the power of the unit and the external AV signal source and then press the INPUT button to shift to Composite mode.
System Connections Connecting to External AV Signal Source Use the audio cable to connect the audio input jacks on the rear panel of the unit to the external AV signal source. Use the S-VIDEO cable to connect the S-VIDEO input jack on the rear panel of the unit to the external AV signal source. After connection, turn on the power of the unit and the external AV signal source and then press the INPUT button to shift to S-VIDEO mode.
System Connections Connecting to External AV Signal Source (COMPONENT) Use the audio and video cables to connect the COMPONENT (Y/Pb/Pr) input Jacks on the rear panel of the unit to the external AV signal source. After connection, turn on the power of the unit and external AV signal source and then press the INPUT button to shift to Component mode.
System Connections Connecting to PC The unit can be connected to PC (person computer) via the VGA cable. Follow the steps and the figure below to connect: 1. Connect one end of the VGA cable to the VGA input jack on the rear panel of the unit. 2. Connect the other end to the PC. 3. Connect one end of the audio cable to the PC audio input jack on the rear panel of the unit. 4. Connect the other end to the PC audio output jack. 5.
System Connections Connecting the Power Cable Plug the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty inserting the plug, turn it over and reinsert it. If the unit will not the used for a long time, disconnect the plug from the outlet.
System Connections Connecting to TV Signal This unit can be connected to the TV signal input source via the TV jack on the rear panel. After connection, turn on the power of the unit, press the INPUT button to shift to TV mode. After connecting to the antenna, turn on the unit, and go on with program searching, you can follow the below steps to select channels: 1. For 0~9 channel: Press the number buttons to select the channel X, wait two seconds and it will go to the selected channel.
TV Function Preparations 1. After connection, press the POWER button to turn on the power. 2. Press the INPUT button to shift to TV mode. You can go on with the following operations: Image Setting Note: This item is only available when there is signal input. Press the MENU button once to enter the setup menu, as shown on the right: In the setup menu, press the ▲▼ button to select Image and then press the OK button to enter the item. Press the ▲▼ button to select.
TV Function Contrast Setup Press the ▲▼ button to select Contrast and press the ◄► button to adjust the value. Press the MENU button to return to the previous menu. Hue Setup Press the ▲▼ button to select Hue and press the ◄► button to adjust the value. Press the MENU button to return to the previous menu. Saturation Setup Press the ▲▼ button to select Saturation and press the ◄► button to adjust the value. Press the MENU button to return to the previous menu.
TV Function Treble Setup Press the ▲▼button to select Treble and press the ◄► button to adjust the level. Press the MENU button to return to the previous menu. Balance Setup Press the ▲▼ button to select Balance and press the ◄► button to adjust the level. Press the MENU button to return to the previous menu. MTS Setup Press the ▲▼ button to select MTS and press the OK button to enter. Press the ▲▼ button to select the desired item and then press the OK button to confirm your selection.
TV Function Parental Setting Note: The Parental Function is the same as that of V-CHIP. Press the MENU button to enter the setup menu. Press the ▲▼ button to select Parental and press the OK button to enter the menu shown on the right. In the Parental setup menu, press the OK button and then use the number buttons to enter the pin. The default pin is 1111. Then press the OK button to continue and display the menu as shown on the right.
TV Function Clear All Press the ▲▼ button to select Clear All and press the OK button to enter. Press the ▲▼ button to select the desired item and then press the OK button to confirm your selection. Press the MENU button to return to the previous menu. TV Rating Press the ▲▼ button to select TV Rating and press the OK button to enter. Press the ▲▼ button to select the desired item and then press the OK button to confirm your selection. Press the MENU button to return to the previous menu.
TV Function CA Eng Rating Press the ▲▼ button to select CA Eng Rating and press the OK button to enter. Press the ▲▼ button to select the desired item and then press the OK button to confirm your selection. Press the MENU button to return to the previous menu. CA Fr Rating Press the ▲▼ button to select CA Fr Rating and press the OK button to enter. Press the ▲▼ button to select the desired item and then press the OK button to confirm your selection. Press the MENU button to return to the previous menu.
TV Function Setup Setting Press the MENU button once to enter the setup menu. Press the▲▼ button to select Setup and press the OK button to enter the menu shown on the right. In the Setup menu, press the▲▼ button to select the desired item and press the OK button to enter. Press the MENU button to return to the previous menu. Tuner/Channel Press the ▲▼ button to select the Tuner/Channel and press the OK button to enter the menu as shown on the right.
TV Function Channel System Press the ▲▼ button to select Channel System and press the OK button to enter. Press the ▲▼ button to select the desired item and then press the OK button to confirm your selection. Press the MENU button to return to the previous menu. Prog Organizer Press the ▲▼ button to select the Prog Organizer and press the OK button to enter the menu as shown on the right. In the Prog Organizer setup menu, press the ▲▼ button to select the desired item.
TV Function Fine Tune Press the ▲▼ button to select Fine Tune and press the OK button to enter. Press the ► or ◄ button to start fine tuning forward or backward. Press the MENU button to return to the previous menu. Language Press the ▲▼ button to select the Language, press the OK button to enter the setup, press the ▲▼ button to select item. Press the MENU button to return to the previous menu. Factory Reset Press the ▲▼ button to select the Factory Reset, press the OK button to resume default status.
Other Function External AV Input Function The unit has external AV input function. It supports S-VIDEO, Composite and Component modes. Use the audio, video and S-Video cable to connect the unit to the external AV signal source such as recorder, vidicon, satellite receiver or game player etc. Then turn on the unit and the external AV signal source. Press the INPUT button to shift to the corresponding mode: S-VIDEO, Composite or Component. Then you can go on to set up the menu in a certain mode.
Troubleshooting SYMPTOM There is no sound. LCD does not display a picture. CHECK ITEM Make sure system connection is correct. Make sure the speakers are not muted. In the TV mode, set the correct sound mode. Make sure the unit is turned on and the connections are correct. Make sure the power adapter is correctly connected. There is no picture or picture moves up and down. Check if the connections with the external AV signal source are correct. Correctly set the items in the picture menu.
Specifications TFT-LCD Resolution 1024 x 768 TFT-LCD Screen Size 15 inches AC100~240V 50/60Hz Power DC 12V 4A Power Consumption < 48W Dimension 345 × 84 × 390mm (LXWXD) Weight About 5.8Kg Ambient Temperature 10~45 degrees DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE "Polaroid" and “Polaroid and Pixel” are trademarks of Polaroid Corporation, Waltham, MA, USA. For service, support and warranty information, visit www.polaroid.com.
- 27 -