Repair Manual Macro 5 SLR Camera October 1998 Rev replaces September 1996 Americas Business Center Technical Services 201 Burlington Road Bedford MA 01730 TEL: 1.781.386.5309 FAX: 1.781.386.
Macro 5 SLR Camera Repair Manual Contents Purpose of this Manual ..................................... 3 Organization of this Manual .............................. 3 Other Documents Required for Service ............ 3 List of Illustrations ............................................. 4 Section 1. Camera Description ......................... 6 Section 2. Theory of Operation ......................... 20 Section 3. Adjustments ..................................... 27 Section 4. Troubleshooting .............
Macro 5 SLR Camera Repair Manual Purpose of this Manual This service manual is intended as a reference guide for Polaroid and Polaroid authorized service personnel. Organization of this Manual Camera Description. General information about camera capabilities and applications. Theory of Operation. Detailed explanation of how the various camera components function during the picture-taking sequence. Adjustments. Procedures for calibrating various camera components after replacement. Troubleshooting.
Macro 5 SLR Camera Repair Manual List of Illustrations Section 1. Camera Description Figure 1-1 Macro 5 SLR Camera ........................................................................... 8 Figure 1-2 Macro 5 SLR Features ..........................................................................10 Figure 1-3 Control Panel .........................................................................................14 Section 2. Theory of Operation Figure 2-1 Camera Setup....................................
Macro 5 SLR Camera Repair Manual List of Illustrations (continued) Figure 5-8 S1/S2 PC Board.....................................................................................53 Figure 5-9 Control Panel .........................................................................................55 Figure 5-10 Logic PC Board....................................................................................58 Figure 5-11 Camera back............................................................................
Macro 5 SLR Camera Repair Manual Section 1. Camera Description IMPORTANT SAFETY INSTRUCTIONS ............................................................. 7 General ................................................................................................................ 8 Features ............................................................................................................... 9 Camera ...................................................................................................
Macro 5 SLR Camera Repair Manual IMPORTANT SAFETY INSTRUCTIONS When servicing the Macro 5 SLR camera, always follow basic safety precautions. CAUTION THE FILM USED BY THE CAMERA CONTAINS A CAUSTIC JELLY THAT IS SAFELY PACKED INSIDE THE FILM PACK. IF YOU SHOULD ACCIDENTLY GET SOME OF THIS JELLY ON YOUR SKIN, WIPE IT OFF IMMEDIATELY AND WASH THE AREA WITH PLENTY OF WATER AS SOON AS POSSIBLE. UNDER ALL CIRCUMSTANCES, KEEP THE JELLY AWAY FROM THE MOUTH AND EYES.
Macro 5 SLR Camera Repair Manual General The Polaroid Macro 5 SLR (Figure 1-1) is a fully automatic, close-up portable camera. It is designed for medical and dental documentation, quality control, law enforcement, and other applications that requires close-up photographs. The Macro 5 SLR has two built-in electronic flash units that provide even illumination. It also has a microprocessor-controlled exposure system that automatically sets the camera for correct exposure at all magnification settings.
Macro 5 SLR Camera Repair Manual Features Camera Basic Macro 5 SLR features include: (Figure 1-2) • • • • • • • • • • • • • Camera Back (Film Holder) Film Door Release Button Two Built-In Electronic Flash Units Lens Dual Light Rangefinder (Ranging Lights) Viewfinder Grid Screen in Viewfinder Tripod or Copystand Socket (on bottom of camera) Battery Compartment Door Battery Compartment (inside hand grip) Right/Left Hand Grips Magnification Selector Knob Shutter (S1) Button Table 1-1 describes the Macro 5
Macro 5 SLR Camera Repair Manual Shutter Button Rangefinder (Aim Light) Right Hand Grip Left Hand Grip Electronic Flash Electronic Flash Lens Rangefinder Aim Light Camera Back Film Door Release Button Camera Back Door Magnification Selector Battery Compartment Door Viewfinder Battery Compartment (inside grip) Control Panel Figure 1-2 Macro 5 SLR Features 10
Macro 5 SLR Camera Repair Manual Table 1-1. Macro 5 SLR Camera Features (Cont’d) Camera Feature Two Built-In Electronic Flash Units Description The two built-in electronic flash units provide even illumination at all magnification settings. Either flash unit can be turned off if side lighting is needed to show texture or elevation. Note: The light output from the remaining flash unit will be increased to produce the correct exposure.
Macro 5 SLR Camera Repair Manual Table 1-1. Macro 5 SLR Camera Features (Cont’d) Camera Feature Description Battery Compartment Door The battery compartment slides open to replace the four (4) Alkaline batteries in the Battery compartment. Battery Compartment The battery compartment contains four (4) AA batteries that provides power for the dual-light rangefinder. Note: Alkaline batteries (Standard or rechargeable) are recommended. Rechargeable NiCad batteries can also be used.
Macro 5 SLR Camera Repair Manual Table 1-1. Macro 5 SLR Camera Features (Cont’d) Camera Feature Red Shutter (S1) Button Description The red shutter (S1) button turns on the ranging lights and actuates the shutter and the flash unit/s when pressed. Pressing the button lightly turns on the camera and the two ranging lights used to focus the camera. Note: The two ranging lights stay on as long as the button is lightly pressed.
Macro 5 SLR Camera Repair Manual Control Panel Figure 1-3 shows the Macro 5 SLR control panel. Table 1-2 describes its features.
Macro 5 SLR Camera Repair Manual Table 1-2. Control Panel Features Camera Feature POWER Button Description Turns the camera On. The flash units begin charging. The camera turns off if the power button is pressed again, or after 30 seconds of inactivity. Note: The camera can also be turned on by slightly pressing the shutter (S1) button. Low Battery Status Light Lights up when the batteries are low. The ranging lights also become dim.
Macro 5 SLR Camera Repair Manual Table 1-2. Control Panel Features (Cont’d) Camera Feature Lighten/Darken Controls Description Makes the picture lighter or darker. Each setting increases or decreases exposure by 1/3 f-stop. The center light is the nominal setting. Pressing the white arrow lightens the picture (increases exposure); pressing the black arrow darkens the picture (decreases exposure). Magnification Status Lights Lights up to indicate the selected magnification setting.
Macro 5 SLR Camera Repair Manual Table 1-2. Control Panel Features (Cont’d) Camera Feature Auxiliary Flash Receptacle Description Standard PC socket for an auxiliary flash. Notes: • An electronic flash must be used for auxiliary lighting. Do Not use tungsten, halogen, or fluorescent lights. • The built-in flash can be combined with auxiliary lighting. • Test exposures may be needed to determine the proper lighten or darken setting for correct exposure.
Macro 5 SLR Camera Repair Manual Specifications Operating Power Ranging Lights: Four (4) AA Alkaline batteries (standard or rechargeable) Camera: Film pack battery. Flash Unit Two built-in flash units. Shutter Speed Fixed (1/50 second). Polaroid Film Types Polaroid High Definition. Type Film: 990 Grid Spectra/Image Note: These high-speed (ISO640/290) film types are balanced for electronic flash and daylight (55000K), and produce positive color prints. Camera Back Modified ProCam camera back.
Macro 5 SLR Camera Repair Manual Specifications (Cont’d) Magnification: Lens-to-subject 0.2x (20%) 0.4x (40%) 1x (100%) 2x (200%) 3x (300%) distance Lens focal 2 length Effective lens aperture Depth 3 of field 52in./130cm 26in./66cm 9.9in./25cm 4.8in./13cm 3.1in./8cm 221mm 188mm 128mm 85.4mm 64mm f/20 f/34 f/47 f/67 f/100 10.6in./27cm 3.8in./10cm 0.86in./2.2cm 0.31in./0.8cm 0.20in./0.5cm Viewfinder Built-in grid screen for consistent framing of subjects. Rangefinder Dual-lights for focusing.
Macro 5 SLR Camera Repair Manual Section 2. Theory of Operation Operation ........................................................................................................... 21 Camera Setup ................................................................................................. 21 Picture Taking .................................................................................................
Macro 5 SLR Camera Repair Manual Operation The following procedures sequentially detail the picture taking operation. For a simplified explanation of this picture taking operation refer to the flow diagrams in Figures 2-1 and 2-2. Camera Setup 1. Set the camera to the desired magnification. Note: If the magnification selector is improperly set (between settings), the camera will not function. For detailed information on how to select magnification, refer to the Macro 5 SLR User's Guide.
Macro 5 SLR Camera Repair Manual 3. Set the lighten/darken buttons to the desired exposure (trim). Notes: • Makes the picture lighter or darker to enhance the specific details of the subject. • Normally the camera provides the correct exposure for subjects of average brightness. • Each setting adjusts the flash output by 1/3 f-stop. The center light is the nominal setting. • White arrow lightens the picture (increases exposure). • Black arrow darkens the picture (decreases exposure). 4.
Macro 5 SLR Camera Repair Manual Camera Set-Up Install batteries Load film pack Set camera parameters Magnification Exposure Date/Time Strobe(s) Take Picture To Figure 2-2 Figure 2-1 Camera Setup 23 Filter
Macro 5 SLR Camera Repair Manual Picture Taking 1. Turn on the camera by lightly pressing the shutter (S1/S2 switch) button. This closes the S1 switch. Closing the S1 switch: • • • • Turns on the top and bottom range (aim) lights to focus the camera. Latches the camera's power on. Starts the strobe charge cycle (charged before self-check routine started). Starts the camera's self-check routine.
Macro 5 SLR Camera Repair Manual 3. While this self-check routine is checking the camera's status, focus and frame the subject. For detailed information on how to properly focus and frame the subject, refer to the Macro 5 SLR User's Guide. 4. Once the camera is properly focused and the status lights are green, press the shutter button (S1/S2) all the way in to take the picture. This action closes the S2 switch. Closing the S2 switch: • Fires the strobes. • Actuates the shutter.
Macro 5 SLR Camera Repair Manual Picture Taking From Figure 2-1 Lightly press shutter button S1/S2 If S1 button released, range lights go out in 15 seconds. Press S1 button lightly to turn on again.
Macro 5 SLR Camera Repair Manual Section 3. Adjustments Ranging (Aim) Lights Adjustment ....................................................................... 28 Grid Adjustment..................................................................................................
Macro 5 SLR Camera Repair Manual Ranging (Aim) Lights Adjustment 1. Place the camera onto the test fixture as shown in Figure 3-1. Test Target area Camera Test Fixture Figure 3-1 Camera Test Fixture 2. Set the magnification selector knob to its 1X position. 3. Turn on the camera. 4. Press the red shutter button lightly to turn on the range lights. The range lights should be merged together and centered in the test target (Figure 3-2).
Macro 5 SLR Camera Repair Manual Figure 3-2 Range Light Adjustment 5. Adjust range lights as follows: • Remove the front cover as explained in section 4 of this service manual. • Determine which range light is out of adjustment. • Loosen the applicable adjustment screw (Figure 3-3) and then manually adjust the range light until it merges with the other range light.
Macro 5 SLR Camera Repair Manual Clamp Clamp Screw Up/Down Adjustment Side-to-Side Adjustment Figure 3-3 Range Light Adjustments 30
Macro 5 SLR Camera Repair Manual Grid Adjustment Note: Make sure the range lights are properly adjusted before adjusting the camera grid. 1. Take a picture of the test target. 2. Using a felt tip pen, draw diagonal lines from corner-to- corner on the picture of the test target (Figure 3-4). Correct Incorrect Figure 3-4 Grid Position Notes: • If the diagonal lines intersect in the center of the grid pattern, no adjustment is needed.
Macro 5 SLR Camera Repair Manual Up/Down Adjustment Screw Side-to-Side Adjustment Screw Figure 3-5 Grid Adjustments 32
Macro 5 SLR Camera Repair Manual Section 4. Troubleshooting Diagnostics Module ............................................................................................
Macro 5 SLR Camera Repair Manual Diagnostics Module A diagnostics module is currently being created. This module is a CD, titled Module 5 Star, that will assist in diagnosing camera malfunctions. It will be available shortly. For ordering, the part number is CPS506.
Macro 5 SLR Camera Repair Manual Section 5. Parts Replacement Required Tools and Equipment .......................................................................... 37 Electrostatic Discharge Warning ........................................................................ 38 Inspection and Cleaning..................................................................................... 38 Disassembly/Assembly of Camera.....................................................................
Macro 5 SLR Camera Repair Manual Logic PC Board .................................................................................................. 57 1. Removal (Figure 5-10) .............................................................................. 57 2. Reassembly............................................................................................... 58 Camera Back ..................................................................................................... 59 1.
Macro 5 SLR Camera Repair Manual Required Tools and Equipment • Pencil Soldering Iron • Solder Sucker • Anti-Static Mat and Wrist Strap • Standard Tool Kit • Torx Driver (6" Apex Torx T-10 Tip) • Small Pair of Diagonal Cutters • Cleaning Tissue or Soft Clean Rags • Universal PLCC Extraction Tool (fits 20-84 pin Micro Controller) 37
Macro 5 SLR Camera Repair Manual Electrostatic Discharge Warning The camera circuitry can easily be damaged by static discharges. Always use an anti-static mat and a wrist-strap when servicing the camera's PC Boards. Inspection and Cleaning Whenever disassembling the camera for parts replacement, always inspect the following assemblies for dust and debris (reagent developer).
Macro 5 SLR Camera Repair Manual Left/Right Cover (Includes Front Cover) 1. Removal (Figure 5-1, 5-2 and 5-2a) a. Turn off power by pressing the POWER button on the camera's control panel. b. Disconnect the camera’s power source as follows: Slide the battery cover open, unsnap the battery cable clip, and lift out the battery holder. c. If applicable, remove the film pack from the camera back. d. Using a torx driver, remove the single screw securing the turret knob to the top of the turret assembly.
Macro 5 SLR Camera Repair Manual Turret Assembly Turret Knob Front Cover Assembly Door Button Adapter Vinyl Pad Figure 5-1 Camera Disassembly j. Using a torx driver, remove the screw securing the bottom of the right cover to the camera back (Figure 5-2). k. Using a torx driver, remove the screw securing the bottom of the left cover to the camera back (Figure 5-2). l Disconnect the battery cable from the left cover tie post.
Macro 5 SLR Camera Repair Manual Note: Front cover assembly is still attached to the left/right cover assembly. n Disconnect both trigger cables (J31) from the trigger PC boards (Figure 5-2a). Note: This should free the left/right - front cover assembly from the rear cover and camera back.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Connect the trigger cables (J31) to its applicable trigger PC boards. Note: Make sure each cable is properly dressed and secured by the white cable clamps attached to the side of the left/right cover. b. Using both hands, gently install the left/right cover assembly (includes the front cover) onto the camera back making sure that it properly aligns with each bottom screw hole and that it properly fits around the turret assembly. c.
Macro 5 SLR Camera Repair Manual Front Cover 1. Removal (Figure 5-3) a. Remove the left/right cover assembly as explained on page 39. b. Using a torx driver, remove the four (4) screws securing the front cover to the left/right covers. c. Lift off the front cover.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Using a torx driver, install and tighten the four (4) screws that secure the front cover to the left/right covers. b. Install the left/right cover assembly as explained on page 42.
Macro 5 SLR Camera Repair Manual Rear Cover 1. Removal (Figures 5-2 and 5-4) a. Remove the left/right cover assembly as explained on page 39. b. Using a torx driver, remove the screw securing the bottom of the rear (right side) cover to the camera back (Figure 5-4). c. Using a torx driver, remove the screw securing the bottom of the rear (left side) cover to the camera back (Figure 5-4). d. Gently lift off the rear cover from the camera back.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Install the rear cover to the camera back. b. Using a torx driver, install and tighten the screw that secures the bottom of the rear (left side) cover to the camera back. c. Using a torx driver, install and tighten remove the screw that secures the bottom of the rear (right side) cover to the camera back. d. Install the left/right cover assembly as explained on page 42.
Macro 5 SLR Camera Repair Manual Bottom Cover 1. Removal (Figure 5-5) a. Remove the left/right cover assembly as explained on page 39. Note: This assembly includes the front cover. b. Remove the rear cover as explained on page 45. c. Remove the camera back door. Note: Refer to the user's guide for instructions on how to remove the camera back door. d. Using a torx driver, remove the three (3) remaining screws securing the bottom cover to the camera back. e.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Place the bottom cover onto the camera back making sure that its two (2) alignment holes properly align with the support posts on the camera back.. b. Using a torx driver, install and tighten the three (3) screws securing the bottom cover to the camera back. c. Install the camera back door. Note: Refer to the user's guide for instructions on how to install the camera back door. d. Install the rear cover as explained on page 46. e.
Macro 5 SLR Camera Repair Manual Strobe PC Board Caution: Shock Hazard - High Voltage Note: Use a dump stick to fully discharge the strobe capacitors before attempting to remove or replace the strobe PC board. 1. Removal (Figure 5-6) a. Remove the left/right cover assembly as explained on page 39. b. Remove the rear cover as explained on page 45. c.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Connect the following electrical cables: • • • • J41 J42 J43 J44 b. Install the strobe PC board making sure that it is properly positioned in its slotted bracket on the rear cover. c. Install the rear cover as explained on page 46. d. Install the left/right cover assembly as explained on page 42.
Macro 5 SLR Camera Repair Manual Trigger PC Boards Caution: Shock Hazard - High Voltage Note: Use a dump stick to fully discharge the strobe capacitors before attempting to remove or replace the trigger PC board. 1. Removal (Figure 5-7) a. Remove the left/right cover assembly as explained on page 39. b. Remove the front cover assembly as explained on page 43. c. Disconnect electrical cable J32 from the applicable trigger PC board. d.
Macro 5 SLR Camera Repair Manual White Trigger Wire Trigger PC Boards J32 Figure 5-7 Trigger PC Boards 2. Reassembly a. Place the new the trigger PC board onto its front cover support mounts. b. Using a torx driver, install and tighten the two (2) screws that secure the trigger PC board to its front cover support mounts. c. Connect electrical cable J32 to the trigger PC board. d. Using a soldering iron, solder the white trigger wire to the trigger coil. Note: Be careful not to damage the trigger coil.
Macro 5 SLR Camera Repair Manual S1/S2 PC Board 1. Removal (Figure 5-8) a. Remove the left/right cover assembly as explained on page 39. b. Using a small pair of diagonal pliers, cut the ty-wrap securing the S1/S2 electrical cable to the right strobe cable. c. Disconnect electrical cable J19 from the logic PC board at rear of camera. d. Using a torx driver, remove the four (4) screws securing the S1/S2 PC board to the right hand grip support mounts. e. Lift out the S1/S2 PC board.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Place the new the S1/S2 PC board onto its right hand grip support mounts. Note: Make sure the large end of the S1 button spring is inserted into the S1 button before the S1/S2 PC board is placed onto its support mounts. b. Using a torx driver, install and tighten the four (4) screws that secure the S1/S2 PC board to its right hand grip support mounts. c. Connect electrical cable J19 to the logic PC board. d.
Macro 5 SLR Camera Repair Manual Control Panel Caution: Shock Hazard - High Voltage Note: Use a dump stick to fully discharge the strobe capacitors before attempting to remove or replace the control panel. 1. Removal (Figure 5-9) a. Remove the left/right cover assembly as explained on page 39. b. Remove the rear cover assembly as explained on page 45. c. Remove the bottom cover as explained on page 47. d. Disconnect the white ribbon cable from the logic PC board. e. Gently pull out the control panel.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Connect electrical cable J11 (X-Sync IN/OUT) to the logic PC board. Note: Be careful not to break the two black wires soldered to the X-Sync receptacle on the control panel. b. Align the two (2) posts on the control panel with the holes on the logic PC board and then gently push in the control panel. (This connects male connector J27 on the logic PC board with the control panel).
Macro 5 SLR Camera Repair Manual Logic PC Board Caution: Shock Hazard - High Voltage Notes: • Use a dump stick to fully discharge the strobe capacitors before attempting to remove or replace the control panel. • The logic PC board firmware (CPU chip) can easily be damaged by static discharges. Always use an anti-static mat and a wrist-strap when removing or replacing it. 1. Removal (Figure 5-10) a. Remove the left/right cover assembly as explained on page 39. b.
Macro 5 SLR Camera Repair Manual Logic PC Board Figure 5-10 Logic PC Board 2. Reassembly a. Gently slide in the logic PC board making sure that its slot aligns with the support hook on the camera back.. b. Connect the following electrical cables to the logic PC board: • • • • • • • • • J13 (Shutter Solenoid) J14 (Aim Lights) J15 (Piezo) J17 (Strobe Control) J18 (Strobe Data) J21 (VBat - Film Pack Battery) J23 (Film Door Switch) J24 (Encoder PC Board) J25 (Camera Back Flex) c.
Macro 5 SLR Camera Repair Manual Camera Back Caution: Shock Hazard - High Voltage Note: Use a dump stick to fully discharge the strobe capacitors before attempting to remove or replace the camera back. 1. Removal (Figure 5-11) a. Remove the left/right cover assembly as explained on page 39. b. Remove the rear cover assembly as explained on page 45. c. Remove the bottom cover as explained on page 47. d. If applicable, remove the strobe, control, or logic PC boards.
Macro 5 SLR Camera Repair Manual Cone Assembly Support Plate Camera Back Figure 5-11 Camera Back 2. Reassembly a. Place cone/turret assembly onto the camera back. Notes: Make sure the: • Cone alignment holes are properly located over the camera back pins. • Plastic support plate is properly positioned on the on the gear side of the camera back; for proper screw hole alignment. • Strobe and logic PC boards, and control panel are properly positioned on the camera back. b.
Macro 5 SLR Camera Repair Manual c. Connect the following electrical cables from the logic PC board: • • • • J15 (Piezo) J16 (Date Code Module) J23 (Film Door Switch) J25 (Camera Back Flex) Note: If it was necessary to remove the strobe and logic PC boards and control panel during the removal of the camera back, make sure that these components are properly reassembled. For reassembly, refer to the appropriate assembly procedures in this section of the manual. d.
Macro 5 SLR Camera Repair Manual Encoder Plate and PC Board 1. Removal (Figure 5-12 and 5-12a) a. Remove the left/right cover assembly as explained on page 39. b. Rotate the turret assembly to its 3x position to expose one of the screws that secures the encoder plate to the lower turret plate. c. Using a torx driver, remove the screw. d. Rotate the turret assembly to its 1x position to expose the other screw that secures the encoder plate to the lower turret plate. e.
Macro 5 SLR Camera Repair Manual Encoder PC Board To J24 on Logic Board Figure 5-12a Encoder PC Board 63
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Rotate the turret assembly to its 1x position. b. Gently slide in the encoder plate making sure its mounting holes align with the screw holes on the lower turret plate. Note: Be careful not to break any of its plastic sensor fingers. c. Using a torx driver, install and tighten the two (2) screws that secure the encoder plate to the lower turret plate. d. Rotate the turret assembly to its 3x position. e.
Macro 5 SLR Camera Repair Manual Turret Assembly 1. Removal (Figure 5-13) a. Remove the left/right cover assembly as explained on page 39. b. Remove the encoder plate and PC board as explained on page 62. c. Using a pair of C-ring pliers, remove the top and lower pivot plate C-rings. d. Pull out the top and lower turret bushings and then lift out the turret assembly.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Slide the turret assembly onto its pivot pins and then insert the top and lower turret bushings onto their respective pivot pins. b. Using a pair of C-ring pliers, install the top and lower pivot plate C-rings to secure the turret assembly to its pivot pins. c. Install the encoder plate and PC board as explained on page 64. d. Install the left/right cover assembly as explained on page 42.
Macro 5 SLR Camera Repair Manual Shutter Solenoid Assembly 1. Removal (Figure 5-14) a. Remove the left/right cover assembly as explained on page 39. b. Disconnect the solenoid cable wires from the solenoid pins. c. Using tweezers, disconnect the shutter extension spring from the shutter pivot post. d. Using a torx driver, remove the two (2) screws securing the solenoid assembly to the viewfinder housing. e. Lift out the solenoid assembly being careful not to lose the solenoid plunger.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Place the solenoid assembly onto the viewfinder support posts. b. Using a torx driver, install and tighten the two (2) screws that secure the solenoid assembly to the viewfinder housing. c. Using tweezers, connect the shutter extension spring to the shutter pivot post. d. Connect the solenoid cable wires to the solenoid pins. e. Install the left/right cover assembly as explained on page 42.
Macro 5 SLR Camera Repair Manual Bulb (Aim Light) Bracket Assembly 1. Removal (Figure 5-15) a. Remove the left/right cover assembly as explained on page 39. b. Remove the rear cover assembly as explained on page 45. c. Disconnect electrical cable J14 from the logic PC board. d. Using a torx driver, remove the screws securing the aim lights. e. Pull out the aim light cable assembly - includes both aim lights.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Install the aim light cable assembly - includes both aim lights. Note: Make sure the aim light cable is properly dressed - around the viewfinder and cone cable claps. b. Using a torx driver, install and tighten the screws that secure the aim lights to their respective bracket assemblies. c. Connect electrical cable J14 to the logic PC board. d. Install the rear cover assembly as explained on page 46. e.
Macro 5 SLR Camera Repair Manual Date Code Module 1. Removal (Figure 5-16) a. Remove the left/right cover assembly as explained on page 39. b. Remove the rear cover assembly as explained on page 45. c. Remove the bottom cover as explained on page 47. d. Disconnect electrical cable J16 from the logic PC board. e Using a torx driver, loosen the six (6) screws securing the camera back to the cone assembly. f.
Macro 5 SLR Camera Repair Manual 2. Reassembly a. Install the date code module onto its camera back rail slot. b. Using a torx driver, tighten the six (6) screws that secures the camera back to the cone assembly. c. Connect electrical cable J16 to the logic PC board. d. Install the bottom cover as explained on page 48. e. Install the rear cover assembly as explained on page 46. f. Install the left/right cover assembly as explained on page 42.
Macro 5 SLR Camera Repair Manual Firmware (Logic PC Board) Caution: Shock Hazard - High Voltage Notes: • Use a dump stick to fully discharge the strobe capacitors before attempting to remove or replace the system firmware (CPU chip). • The CPU chip can easily be damaged by static discharges. Always use an anti-static mat and a wrist-strap when removing or replacing it. 1. Removal (Figure 5-17) a. Remove the left/right cover assembly as explained on page 39. b.
Macro 5 SLR Camera Repair Manual Logic Board CPU Chip Figure 5-17 Firmware CPU 2. Reassembly a. Properly position the replacement CPU squarely into its socket making sure that its beveled corner goes to the beveled corner of the socket. b. Place a thumb in the middle of the CPU and then evenly squeeze the replacement CPU into place. Note: The replacement CPU should be close to flush and parallel with the top of its socket when it is properly seated. c. Install the control panel as explained on page 56.
Macro 5 SLR Camera Repair Manual Section 6. Schematics Figure 6-1 S1/S2 PC Board ..........................................................................................76 Figure 6-2 Encoder PC Board.......................................................................................77 Figure 6-3 Trigger PC Board.........................................................................................78 Figure 6-4 Strobe PC Board (1 of 1) ...............................................................
Macro 5 SLR Camera Repair Manual Figure 6-1 S1/S2 PC Board 76
Macro 5 SLR Camera Repair Manual Figure 6-2 Encoder PC Board 77
Macro 5 SLR Camera Repair Manual Figure 6-3 Trigger PC Board 78
Macro 5 SLR Camera Repair Manual Figure 6-4 Strobe PC Board (1 of 1) 79
Macro 5 SLR Camera Repair Manual Figure 6-5 Strobe PC Board (2 of 2) 80
Macro 5 SLR Camera Repair Manual Figure 6-6 Logic PC Board (1 of 1) 81
Macro 5 SLR Camera Repair Manual Figure 6-7 Logic PC Board (2 of 2) 82
Macro 5 SLR Camera Repair Manual Figure 6-8 Communication PC Board 83
