ENGLISH Technical Assistance or Service If anything is missing or damaged, or if your speaker fails to operate, notify Polk Audio Customer Service immediately at 800-377-7655. If, after following the hookup directions, you experience difficulty, please double-check all wire connections.
ENGLISH PLEASE TAKE INVENTORY INSIDE YOUR SURROUNDBAR CHT CARTONS: Please check to ensure you have everything in your Polk Audio® SurroundBar® 400 Component Home Theater (CHT) or your SurroundBar 500 CHT carton. Inside, you should find: SURROUNDBAR 400 CHT: SURROUNDBAR 400 CHT: SurroundBar 400 loudspeaker Wall mount bracket 15' (4.6m) color-coded cable 2 rubber feet Owner’s manual Online registration card SurroundBar 400 Loudspeaker Wall Mount Bracket 15' (4.
RESTING THE SURROUNDBAR ON A SHELF MOUNTING THE SURROUNDBAR ON A WALL The SurroundBar’s detachable feet can be reversed and, depending on their orientation, will make the bar sit flat or tilt up at 10°. Without the feet, the SurroundBar tilts up 5°. Press the detachable rubber feet into the groove on the bottom of the SurroundBar, plug in the speaker cable and set the mode switch to either 7CH, 5CH or LCR, depending upon your intended setup (see pages 6 - 10).
MOUNTING THE SURROUNDBAR 500 CHT SDA CONTROL MODULE WALL MOUNTING THE SDA CONTROL MODULE Overall Dimensions The SurroundBar 500 CHT SDA Control Module can be mounted on a wall, either vertically or horizontally, into a rack using the supplied rack mount ears, or it may be placed on a flat surface. The location of your other electronic components will determine which location will work best for you. 1. 8" H (20.32cm) 2. 17" W (43.18cm) Keyhole Slots 3. 14 3/4" W (37.
SURROUNDBAR 400 CHT HOOKUP DIAGRAMS The colors for the inputs & wires are as follows: The SurroundBar 400 CHT can operate in one of three channel modes: 7CH, 5CH or LCR. If you choose to operate your SurroundBar 400 CHT in the 5CH or LCR configuration, “tie off” the unused channel wires with wire nuts.
SURROUNDBAR 400 CHT HOOKUP DIAGRAMS 5CH HOOKUP Note: Only use this hookup if you are using dedicated satellite loudspeakers for the Surround Back channels. Note: Remember to “tie off” the unused channel wires with wire nuts. SBL SBR SPEAKER IN LCR / 5CH / 7CH SL SURROUND BACK SPEAKERS SURROUND SPEAKERS FL FR FRONT SPEAKER A SR CENTER SPEAKER L R RECEIVER C LCR HOOKUP Note: Only use this hookup if you are using dedicated satellite loudspeakers for the Surround and Surround Back channels.
SURROUNDBAR 500 CHT HOOKUP DIAGRAMS The SurroundBar 500 CHT can operate in one of three channel modes: 7CH, 5CH or LCR. Note: Remember to set the mode switch, located on the back of the SDA Control Module, to either 7CH, 5CH or LCR, depending on your system configuration (see page 12 for details).
SURROUNDBAR 500 CHT HOOKUP DIAGRAMS 5CH HOOKUP Note: Only use this hookup if you are using dedicated satellite loudspeakers for the Surround Back channels. SDA CONTROL MODULE LCR / 5CH / 7CH SL SBL SL FL FL C C FR SR FR SR SPEAKER OUT SBR SURROUND BACK SPEAKERS SURROUND SPEAKERS FRONT SPEAKER A CENTER SPEAKER L R RECEIVER Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.
SURROUNDBAR 500 CHT HOOKUP DIAGRAMS LCR HOOKUP Note: Only use this hookup if you are using dedicated satellite loudspeakers for the Surround and Surround Back channels.
SPEAKER AND SUBWOOFER HOOKUPS FOR CHT SURROUNDBARS SUBWOOFER HOME THEATER RECEIVER/PROCESSOR For 5CH Mode: Connect the Surround Back Left (SBL) and Surround Back Right (SBR) channels from the outputs of your receiver to the corresponding inputs on the two satellite loudspeakers. SUBWOOFER HOOKUP To hook up a subwoofer, use a single RCA cable and make the connection from the SUB OUT connection on your receiver to the LFE input on your subwoofer. (See wire hookup diagram above.
SURROUNDBAR CHANNEL MODE OPTIONS While the SurroundBar CHT was designed to reproduce an enveloping surround experience in the 7CH mode, we have given you the option of adding satellite loudspeakers to create even more precise surround effects. Connect additional satellite speakers and set the SurroundBar’s channel mode switch to either LCR or 5CH. (See optional settings below) TV SURROUNDBAR (7CH) SURROUNDBAR ONLY IN 7CH MODE No satellites are hooked up.
SURROUNDBAR SPEAKER SET-UP Connect your SurroundBar 500 CHT or 400 CHT system to your surround sound receiver/processor referring to the hookup instructions on pages 6 - 10. Set Channel Levels: 1. Set Front Left, Center and Front Right to “Zero” (0dB). Do not use the “Auto Setup” feature if it is included in your receiver. Because the SurroundBar produces surround sound from a single front-mounted speaker, the auto setup feature will not operate properly. 2.
SYMPTOM DIAGNOSIS No sound Receiver “off,” or in standby mode; selected source not active, volume low or system muted; speaker wires and/or component interconnect cables not connected properly. Turn on receiver; select appropriate source, turn up volume, unmute; check wiring. No surround sound effect No surround content in program material; two channel source and receiver set to stereo; surround sound processing disabled; surround channel volume settings too low.
FRANÇAIS FAITES L’INVENTAIRE CONTENU DE LA BOÎTE SURROUNDBAR CHT Assurez-vous que la boîte de votre Polk Audio® SurroundBar® 400 Component Home Theater (CHT) ou SurroundBar 500 CHT contient tous les items énumérés ci-dessous: SURROUNDBAR 400 CHT: SURROUNDBAR 400 CHT: Enceinte SurroundBar 400 Support mural Câble 15' (4,6m) à code de couleurs 2 pieds de caoutchouc Manuel d’utilisation Carte d’enregistrement en ligne Enceinte SurroundBar 400 Support mural Câble 15' (4,6m) à code de couleurs SURROUNDBAR
LA SURROUNDBAR SUR UNE ÉTAGÈRE INSTALLATION DE LA SURROUNDBAR AU MUR Lorsque la SurroundBar est installée sur une étagère, ses pieds détachables peuvent être renversés, vous permettant de placer l’enceinte à plat ou inclinée à un angle de 10°. Sans les pieds, l’enceinte est inclinée à un angle de 5°. Pressez les pieds de caoutchouc dans la rainure située sous la SurroundBar, connectez le câble CHT fourni puis réglez le commutateur LCR, 5CH, 7CH à la position conforme à la configuration de votre système.
INSTALLATION DU MODULE DE CONTRÔLE SDA DE LA SURROUNDBAR 500 CHT INSTALLATION MURALE DU MODULE SDA Dimensions hors tout Le module de contrôle SDA de la SurroundBar 500 CHT peut être placé sur une surface plate, installé au mur (à la verticale ou à l’horizontale) ou dans un bâti en utilisant les équerres fournies. L’emplacement de vos autres composants saura déterminer son emplacement idéal. 1. 8" H (20,32cm) 2. 17" W (43,18cm) Fentes en trou de serrure 3.
DIAGRAMME DE CÂBLAGE DE LA SURROUNDBAR 400 CHT La SurroundBar 400 CHT vous offre un choix de trois configurations de canaux: 7CH, 5CH ou LCR. Si vous choisissez la configuration 5CH ou LCR, condamnez les fils inutilisés avec des capuchons de connexion. Couleurs des fils du câble CHT et des entrées: Note: N’oubliez pas de régler le commutateur 7CH, 5CH, LCR situé à l’arrière de la Surroundbar à la position conforme à la configuration de votre système. (Voir page 24 pour plus de détails.
DIAGRAMME DE CÂBLAGE DE LA SURROUNDBAR 400 CHT CONNEXION 5CH Note: N’utilisez ce type de connexion que si vous utilisez des enceintes satellites dédiées aux canaux arrière ambiophoniques (Surround Back). Note: N’oubliez pas de condamner les fils inutilisés avec des capuchons de connexion.
DIAGRAMMES DE CÂBLAGE DE LA SURROUNDBAR 500 CHT La SurroundBar 500 CHT vous offre un choix de trois configurations de canaux: 7CH, 5CH ou LCR. Note: N’oubliez pas de régler le commutateur 7CH, 5CH, LCR situé à l’arrière du module SDA à la position 7CH, 5CH ou LCR conforme à la configuration de votre système. (Voir page 24 pour plus de détails.).
DIAGRAMMES DE CÂBLAGE DE LA SURROUNDBAR 500 CHT CONNEXION 5CH Note: N’utilisez ce type de connexion que si vous utilisez des enceintes satellites dédiées aux canaux arrière ambiophoniques (Surround Back). MODULE DE CONTRÔLE SDA LCR / 5CH / 7CH SL SBL SL FL FL C C FR SR FR SR SPEAKER OUT SBR SURROUND BACK SPEAKERS SURROUND SPEAKERS FRONT SPEAKER A CENTER SPEAKER L R RÉCEPTEUR Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.
DIAGRAMMES DE CÂBLAGE DE LA SURROUNDBAR 500 CHT CONNEXION LCR Note: N’utilisez ce type de connexion que si vous utilisez des enceintes satellites dédiées aux canaux ambiophoniques et ambiophoniques arrière (Surround et Surround Back).
CONNEXION D’ENCEINTES ET D’UN SUBWOOFER AVEC UNE SURROUNDBAR CHT SUBWOOFER CINÉMA MAISON RÉCEPTEUR/PROCESSEUR CONNEXION D’UN SUBWOOFER Pour connecter un subwoofer, utilisez un seul câble RCA et raccordez la sortie SUB OUT de votre récepteur à l’entrée LFE de votre subwoofer (voir le diagramme de connexion ci-dessus). Si votre subwoofer n’a pas d’entrée LFE, utilisez l’entrée LINE IN R ou L et réglez le contrôle LOW PASS au maximum du sens horaire.
OPTIONS DE CONFIGURATIONS DE CANAUX Quoique la SurroundBar CHT ait été conçue pour reproduire une ambiophonie enveloppante en mode 7CH, vous pouvez y ajouter des enceintes satellites pour recréer des effets ambiophoniques encore plus précis. Connectez des enceintes satellites additionnelles et réglez le commutateur 7CH, 5CH, LCR à la position à LCR ou 5CH. (Voir réglages optionnels ci-dessous.) TV SURROUNDBAR (7CH) LA SURROUNDBAR EN MODE 7CH SEULEMENT Aucune enceinte satellite.
CONFIGURATION DE L’ENCEINTE SURROUNDBAR Connectez votre système SurroundBar 500 CHT ou 400 CHT à votre récepteur/processeur ambiophonique en suivant les instructions de connexion (pages 18 - 22). N’utilisez pas la fonction «Auto Setup» de votre récepteur. Cette fonction ne fonctionnerait pas correctement parce que la SurroundBar reproduit du son ambiophonique d’une seule et unique enceinte avant.
PROBLÈME CAUSE Pas de son Le récepteur est éteint ou en mode de veille (standby), la source sélectionnée n’est pas active, le volume est trop bas ou le système est en mode «Mute» (sourdine); les fils de haut-parleur et/ou les câbles des composants sont mal connectés. Allumez le récepteur; sélectionnez la source appropriée, montez le volume, désactivez le mode «Mute,» vérifiez toutes les connexions et tout le câblage.
ESPAÑOL HAGA INVENTARIO Asegúrese de tenerlo todo en la caja de la SurroundBar® 400 para Cine en Casa de Componentes (Component Home Theater, CHT) o la SurroundBar 500 CHT. Dentro de la caja debe haber lo siguiente: EN LAS CAJAS DE LAS SURROUNDBAR CHT ENCONTRARÁ LO SIGUIENTE: SURROUNDBAR 400 CHT: SURROUNDBAR 400 CHT: Altavoz SurroundBar 400 Altavoz SurroundBar 400 Soporte de montaje en la pared Cable de 15 pies (4.
SI COLOCA LA SURROUNDBAR SOBRE UNA REPISA MONTAJE DE LA SURROUNDBAR EN UNA PARED Si coloca la SurroundBar sobre una repisa, se le pueden invertir las patas desprendibles y, dependiendo de la orientación de las patas, la barra queda horizontal o se orienta 10° hacia arriba. Sin las patas, la SurroundBar se orienta 5° hacia arriba.
MONTAJE DEL MÓDULO DE CONTROL SDA DE LA SURROUNDBAR 500 CHT MONTAJE EN LA PARED DEL MÓDULO DE CONTROL SDA El módulo de control SDA de la SurroundBar 500 CHT se puede poner sobre una superficie plana, montar en la pared vertical u horizontalmente o montar en un armazón con las escuadras de montaje incluidas. La ubicación de los otros componentes electrónicos determina la mejor ubicación en su caso. Dimensiones generales 1. 8 plg. de alto (20.32 cm) 2. 17 plg. de ancho (43.
DIAGRAMAS DE CONEXIÓN DE LA SURROUNDBAR 400 CHT Los colores de las entradas y los cables son los siguientes: La SurroundBar 400 CHT puede funcionar en una de tres modalidades de canal: 7CH, 5CH o LCR. Si decide hacer funcionar la SurroundBar 400 CHT en la configuración 5CH o LCR, póngales conectores de torsión a los cables de los canales que no conecte.
DIAGRAMAS DE CONEXIÓN DE LA SURROUNDBAR 400 CHT CONEXIÓN 5CH Nota: Haga esta conexión sólo si va a instalar altavoces satélite dedicados a los canales surround traseros. Nota: Recuerde ponerles conectores de torsión a los cables de los canales que no conecte.
DIAGRAMAS DE CONEXIÓN DE LA SURROUNDBAR 500 CHT La SurroundBar 500 CHT puede funcionar en una de tres modalidades de canal: 7CH, 5CH o LCR. Nota: Recuerde fijar el conmutador de modalidad, ubicado en la parte de atrás del módulo de control SDA, en la posición 7CH, 5CH o LCR, dependiendo de la configuración del sistema (vea los detalles en la página 36).
DIAGRAMAS DE CONEXIÓN DE LA SURROUNDBAR 500 CHT CONEXIÓN 5CH Nota: Haga esta conexión sólo si va a instalar altavoces satélite dedicados a los canales surround traseros. MÓDULO DE CONTROL SDA LCR / 5CH / 7CH SL SBL SL FL FL C C FR SR FR SR SPEAKER OUT SBR SURROUND BACK SPEAKERS SURROUND SPEAKERS FRONT SPEAKER A CENTER SPEAKER L R RECEPTOR Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.
DIAGRAMAS DE CONEXIÓN DE LA SURROUNDBAR 500 CHT CONEXIÓN LCR Nota: Haga esta conexión sólo si va a instalar altavoces satélite dedicados a los canales surround y los canales surround traseros.
CONEXIONES DE ALTAVOZ Y DE SUBWOOFER PARA LAS SURROUNDBAR CHT SUBWOOFER CINE EN CASA RECEPTOR O PROCESADOR CONEXIÓN DE SUBWOOFER Para un subwoofer, conecte un solo cable RCA entre la salida de subwoofer (OUTPUT/SUBWOOFER) del receptor y la entrada de efectos de bajas frecuencias (Low Frequency Effects, LFE). (Vea el diagrama de conexión que se muestra arriba.
OPCIONES DE MODALIDAD DE CANAL DE LA SURROUNDBAR Aunque la SurroundBar CHT fue diseñada para producir una experiencia de sonido surround envolvente en la modalidad 7CH, le hemos dado a usted la opción de agregar altavoces satélite para crear efectos de sonido surround aún más precisos. Conecte altavoces satélite adicionales y fije el conmutador de modalidad de canal de la SurroundBar en la posición LCR o 5CH. (Vea las configuraciones opcionales que se presentan a continuación.
CONFIGURACIÓN DE ALTAVOCES DE LA SURROUNDBAR Conecte el sistema SurroundBar 500 CHT o 400 CHT al receptor o procesador de sonido surround consultando las instrucciones de conexión que se encuentran en las páginas 30 a 34. Si su receptor tiene una característica de autoconfiguración (Auto Setup), no la utilice. Como la SurroundBar produce sonido surround a partir de un solo altavoz montado al frente, la característica de autoconfiguración no funciona correctamente. 7.
SÍNTOMA DIAGNÓSTICO REMEDIO No hay sonido El receptor está apagado (“off”) o en modalidad de espera; la fuente seleccionada no está activa, el volumen está bajo o el sistema está silenciado; los cables de altavoz y/o los cables de interconexión de componentes no están conectados correctamente. Encienda el receptor; seleccione la fuente apropiada, suba el volumen, desactive el silenciador; revise el cableado.
Limited Warranty Garantie Limitée Polk Audio, Inc. warrants to the original purchaser only that this Polk Audio Loudspeaker Product (the “Product”) will be free from defects in materials and workmanship for a period of five (5) years from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this Warranty will automatically terminate prior to the expiration of the five (5) years if the original retail purchaser sells or otherwise transfers the Product to any other party.
5601 Metro Drive, Baltimore, MD 21215 Polk Audio is a DEI Holdings, Inc. Company. Polk Audio, Polk, The Speaker Speicalists, SDA and SurroundBar are registered trademarks of Polk Audio, Inc.