Active In-Wall/In-Ceiling Speakers Owner’s Manual LCi-IP SERIES LC80i-IP LC265i-IP
ENGLISH ment. What’s more, LCi-IP speakers already come with an award-winning reputation, because they use the same driver technologies as Polk Audio's award winning high-end LSi Series. The built-in DSP controls the electronic crossover, frequency equalization, bass enhancement and room optimization.
INSTALLING LCi-IP SPEAKERS Important Note: If installing LCi-IP speakers in an external wall, the operating ambient temperature of the speakers is 0-50° C (32-122° F). For most types of construction, the external walls will be insulated, but it is important that insulation does not come in contact with the speaker’s amplifier. INSTALLATION RECOMMENDATION FOR OPTIMUM PERFORMANCE Note: Polk Audio performance enclosures are sold separately.
Figure 2 Note: Most measurements will be taken from the center of the tweeters. To take these measurements, you will need: a tape measure and a protractor. You may also be able to determine the necessary measurements from a blueprint or floorplan. Making A Speaker Configuration File Offsite INTERPRETING THE LEDS FAQs To help you work more efficiently and save time, you can make a speaker configuration file offsite.
TROUBLESHOOTING CONTINUED TROUBLESHOOTING Problem No audio Possible Reason(s) Audio signal is not connected to the speaker. The speaker’s software is not configured to work with the MRAV. The speaker’s configuration switches are not set correctly. No power. The MRAV does not recognize the speaker. Speaker is playing the wrong audio channel. No control The speaker’s CHANNEL switch is in the wrong position. The wiring for the speaker is incorrect. Loose or bad NETWORK connection.
1 Disconnect all cables. Disconnect all cables. Disconnect all cables. Disconnect all cables. Disconnect all cables. Disconnect all cables. 2 Remove the (4) Torx screws (size T-10) holding the heat sink to the amp housing. Set the screws safely aside. Remove the (4) Torx screws (size T-10) holding the heat sink to the amp housing. Set the screws safely aside. Remove the (4) Torx screws (size T-10) holding the heat sink to the amp housing. Set the screws safely aside.
Hookup (Independent Control) Hookup OPTIONAL CHANNEL 1 CHANNEL 1 CHANNEL 2 CHANNEL 2 CHANNEL 1 CHANNEL 2 NETWORK IN NETWORK IN COMM COMM NETWORK IN COMM Y A 1 Y A 1 Y A N B 2 N B 2 N B CONTROL CFG CONTROL CHANNEL* CFG CONTROL CHANNEL 1 2 CFG CHANNEL * Channel can be 1 or 2 depending on configuration.
CENTER CHANNEL Hookup 5a: ANALOG (Independent Control When Used with Hookup 3a or 3b) Hookup CHANNEL 1 CHANNEL 1 CHANNEL 1 CHANNEL 2 CHANNEL 2 CHANNEL 2 NETWORK IN NETWORK IN NETWORK IN COMM COMM COMM Y A 1 Y A 1 N B 2 N B 2 CONTROL CFG CHANNEL CONTROL CFG CHANNEL Y A N B CONTROL CFG 1 2 CHANNEL CENTER CHANNEL Hookup 5b: ANALOG (Independent Control When Used with Hookup 4a or 4b) CHANNEL 1 CHANNEL 2 NETWORK IN COMM Y A N B CONTROL 44 Polk Audio Customer Service
230 CAUTION ATTENTION RISK OF ELECTRIC SHOCK RISQUE D’ÉLECTROCUTION DO NOT OPEN NE PAS OUVRIR ON AC MAIN 120 CAUTION ATTENTION RISK OF ELECTRIC SHOCK RISQUE D’ÉLECTROCUTION DO NOT OPEN NE PAS OUVRIR 230 ON OFF AC MAIN OFF 120 INPUT: 90-132 OR 180-264 VAC 7.4/3.7A (50-60Hz) OUTPUT: +48V (7.3A)350W F10AL250W INPUT: 90-132 OR 180-264 VAC 7.4/3.7A (50-60Hz) OUTPUT: +48V (7.3A)350W F10AL250W This hookup works for both the LC265i-IP and the LC80i-IP.
NOTES LIMITED WARRANTY Polk Audio, Inc., warrants to the original retail purchaser only. This warranty will terminate automatically prior to its stated expiration if the original retail purchaser sells or transfers the Product to any other party. Polk Audio, Inc.
5601 METRO DRIVE BALTIMORE, MARYLAND 21215 800-377-7655 (US & CAN, OUTSIDE US 410-358-3600) WWW.POLKAUDIO.COM “Polk Audio,” “Dynamic Balance” and “Acoustic Resonance Control” are registered trademarks of Polk Investment Corporation used under license by Polk Audio Incorporated.
