ENGLISH FRANCAIS Polk Audio-A Passion for Sound Polk Audio-La passion du son Please take a moment and read through this manual before you get started. Installing acar audio system is a serious project. If you have any doubts about your ability to execute any of the installation steps found in this manual, save yourself a lot of grief and contact your local authorized Polk Audio AutoSound dealer. He (or she) is a professional installer and ready to help you get the most for your autosound dollar.
ESPANOL DEUTSCH Polk Audio-Pasion por el Sonido Polk Audio-Eine Leidenschaft fiir Sound Lea todo este manual antes de comenzar. Instalar un sistema de sonido de autom6vil es un proyecto serio. Si tiene dudas sobre su capacidad de lIevar a cabo alguno de los pasos de instalaci6n indicados en este manual. ah6rrese problemas y comunfquese con su distribuidor local autorizado Polk Audio de sonido de autom6viles.
ITALIANO PORTUGUES Polk Audio-La Passione del Suono Polk Audio-Paixao por Som Prima di cominciare, accertatevi di aver letto questa manuale. L'installazione di un impianto audio per auto e una cosa seria. In caso di dubbi sull'esecuzione di alcune delle fasi di installazione contenute in questa manuale, vi invitiamo a rivolgervi subito al rappresentante Polk Audio AutoSound autorizzato di zona.
ENGLISH WARNING High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result. They may also impair a driver's ability to hear traffic sounds or emergency vehicles. Use common sense and practice safe listening habits when listening to or adjusting your audio system. 7. Fuse Replacements 8. 4mm Allen Wrench 9. Wire Harness 10. Owner's Manual 11. Online Registration Card 12. Remote Volume Module 13.
ENGLISH Tools You May Need • Phillips head screwdriver • Solderless, crimp-on connectors and a crimping tool listening material. If you hear distortion-turn the volume down or risk damaging your speakers. You can damage just about any speaker, regardless of power rating, if you drive an amplifier to or beyond the point of distortion.
10. Battery and ground connections to the vehicle should be made with crimped ring terminals of the appropriate size (surface area is what counts;) soldering the terminals after crimping is also recommended. 11. Due to the high-frequency MOSFET switching power supply, filtering the power cable is not generally required (remember that the amp can't deliver full output if the power supply is restricted.) Proper grounding of the signal source is mandatory for the amplifier to reach its performance peak.
ENGLISH 9. Phase Switch-D° or 1BO° selectable for switching the phase output to the woofer. 10. LED/FAN Connector-Allows connection of an optional cooling fan for the amplifier. 11. Status LED-Will illuminate GREEN to indicate the amplifier is on and operating normally, and will be illuminated RED if the amplifier shuts down due to short circuit, DC offset, or overheating detected by onboard protection circuitry.
FIGURE 4-SPEAKER WIRING DIAGRAMS Single Subwoofer Connection (top view) + Two Subwoofer Connection (top view) + + + NOTE: The dual (+) and (-J sub-out terminals of the PA400.1. PA600.1 and PA1200.1 are paralleled internally. and the combined load impedance should be taken into consideration when connecting multiple subwoofers. COMBINING AMPUAERS EXTERNAL SYNCED BRIDGED The Polk 600.1 and 1200.
ENGLISH PARALLEL SYNCED GAIN CONNECnONS~ErnNGS Refer to Figure 5 for wiring details. 1. Input Signal-Connect these RCA jacks as described in the Front Panel Connection section of this guide. 2. SLAVE/MASTER Switch• Set the SlAVE/MASTER switch on the master amplifier to the MASTER position. • Set the SlAVE/MASTER switch on the slave amplifier to the SLAVE position.
Subwoofer Wiring (top view) Slave Master + + + + + + NOTE: The dual (+) and (-) sub-out terminals are paralleled internally and the combined load impedance should be taken into consideration when connecting multiple subwoofers. EXTERNAL SYNCED BRIDGED CONNECnONS~ETnNGS 1. Input Signal-Connect these RCA jacks as described in the Front Panel Connection section of this guide. 2. SLAVE/MASTER Switch• Set the SLAVE/MASTER switch on the master amplifier to the MASTER position.
ENGLISH FIGURE &-EXTERNAL SYNCED BRIDGED (PA600.1/PA1200.1) MASTER AMPLIFIER INPUT LINE OUT PHASE MASTER SLAVE IIj INPUT R L O· 180· IJj PHASE LINE OUT MASTER SLAVE -«!) ~ O· 180· tlIlli SLAVE AMPLIFIER w w w . POL K A U 0 I 0 .
MULTIPLE AMPLIFIER COMBINATIONS The PA400.1, PABOO.1, and PA1200.1 subwoofer amplifiers can also be used in Multiples of the MASTER/SLAVE combinations allowing for unlimited expansion to a system's subwoofer section. To use multiples of amplifier combinations the following directions must be adhered to for best results. • Audio Signal-Divide the head unit or processor audio signal to the master amplifiers by using RCA Y adapters.
ENGLISH CEA SPECIFICATIONS - PA40D.1 Power Output: 200 Watts RMS x 1 at 4 Ohms and::;; 1% THD+N Signal to Noise Ratio: -60 dBA (reference 1Watt into 4 Ohmsl Additional Power: 400 Watts RMS x 1at 1 Ohm and::;; 1% THD+N PA6DD.1 Power Output: 300 Watts RMS x 1at 4 Ohms and::;; 1% THD+N Signal to Noise Ratio: -60 dBA (reference 1Watt into 4 Ohms) Additional Power: 600 Watts RMS x 1at 1 Ohm and::;; 1%THD+N PA12DD.
This is your Product Model and Serial Number. Enter this number in the "Serial Number" space when registering your product online. Keep this card handy for Model and Serial Number reference when calling Polk Customer Service. polkaudio® Register Your New Polk Audio Product Online NOW for aChance to win $500 of Polk Product www.polkaudio.com/registration/ Become a valued member of the Polk Family and get a ch·ance to FREE Speakers.