Glideforce High-Speed LD Linear Actuator w/ Feedback - Datasheet

ManualsBrandsPololu ManualsLinear ActuatorsGlideforce High-Speed LD Linear Actuator w/ Feedback, 12kgf, 4In Stroke, 12V

Concentric International

1901 Bell Ave., Suite 18, Des Moines, IA 50315

www.concentricintl.com

Rev. 20171208

Page 1 of 6

LINEAR ACTUATOR

LIGHT DUTY SERIES

Product Data Sheet

Standard Features:

• Compact design

• All aluminum frame and extension tube

• Nominal stroke lengths: 2” [50mm], 4” [100mm], 6” [150mm], 8” [200mm],

10” [250mm], 12” [300mm]

• Input voltage: 12VDC, 24VDC

• Standard gear ratio: 20:1 [other ratios available]

• Rated load range: 34 lbs. [150 Newtons] –to- 225 lbs. [1000 Newtons]

• Maximum static load: 562 lbs. [2,500 Newtons]

• Maximum current draw: 3.2 Amps @ 12 VDC

• Speed at no load: 0.28 in/sec [7 mm/sec] –to- 1.73 in/sec [43.9 mm/sec]

• Speed at full load: 0.22 in/sec [5.5 mm/sec] –to- 1.44 in/sec [36.5 mm/sec]

• Standard preset limit switches at both ends of stroke

• Noise level: ≤70dB

• Mounting hole diameter (both ends): 1/4” [6.4 mm]

• Duty cycle: 25% or 1 min continuous operation in 4 min.

• Working temperature: -13F [-25C] +149F [+65C]

• IP rating: IP65

Accessories:

• Mounting brackets

• Direction reversing switches

• Wired and wireless controllers

• Direction reversing relays

Summary of content (6 pages)

PAGE 1
LINEAR ACTUATOR LIGHT DUTY SERIES Product Data Sheet Standard Features: • • • • • • • • • • • • • • • • Compact design All aluminum frame and extension tube Nominal stroke lengths: 2” [50mm], 4” [100mm], 6” [150mm], 8” [200mm], 10” [250mm], 12” [300mm] Input voltage: 12VDC, 24VDC Standard gear ratio: 20:1 [other ratios available] Rated load range: 34 lbs. [150 Newtons] –to- 225 lbs. [1000 Newtons] Maximum static load: 562 lbs. [2,500 Newtons] Maximum current draw: 3.2 Amps @ 12 VDC Speed at no load: 0.
PAGE 2
LINEAR ACTUATOR LIGHT DUTY SERIES Dimensions – Actuator Without Potentiometer 6.4 6.4 Nominal Stroke Actual Stroke (S) Retracted Length (A) Extended Length 2” 4” 6” 8” 10” 12” in mm in mm in mm in mm in mm in mm 1.97 50 3.94 100 5.91 150 7.87 200 9.84 250 11.81 300 6.22 158 8.23 209 10.24 260 12.24 311 14.25 362 16.26 413 8.19 208 12.17 309 16.14 410 20.19 511 24.09 612 28.07 713 Concentric International 1901 Bell Ave.
PAGE 3
LINEAR ACTUATOR LIGHT DUTY SERIES Dimensions – Actuator With Potentiometer 6.4 6.4 Nominal Stroke Actual Stroke (S) Retracted Length (A) Extended Length 2” 4” 6” 8” 10” 12” in mm in mm in mm in mm in mm in mm 1.97 50 3.94 100 5.91 150 7.87 200 9.84 250 11.81 300 7.68 195 9.69 246 11.69 297 13.70 348 15.71 399 17.72 450 9.65 245 13.62 346 17.60 447 21.57 548 25.55 649 29.53 750 Concentric International 1901 Bell Ave.
PAGE 4
LINEAR ACTUATOR LIGHT DUTY SERIES Performance Data Gear Ratio 5:1 10:1 20:1 30:1 40:1 Gear Ratio 5:1 10:1 20:1 30:1 40:1 Max Load/Dynamic Lbs. [US] 34 56 112 180 225 Newtons 150 250 500 800 1000 Speed/No Load inches/sec 1.73 1.09 0.57 0.37 0.28 Speed/Max Load mm/sec 43.9 27.6 14.6 9.5 7.0 inches/sec 1.44 0.93 0.48 0.30 0.22 mm/sec 36.5 23.5 12.3 7.5 5.5 Typical Current (A) No Load 12 VDC 1.2 1.2 1.2 1.2 1.2 Full Load 24 VDC 0.6 0.6 0.6 0.6 0.6 12 VDC 3.2 3.2 3.2 3.2 3.2 24 VDC 1.6 1.6 1.6 1.6 1.
PAGE 5
LINEAR ACTUATOR LIGHT DUTY SERIES Electrical Without Potentiometer Red + // Black - : Extend Red - // Black + : Retract With Potentiometer Red + // Black - : Retract Red - // Black + : Extend Value of POT Stroke (in / mm) Resistance 1.97 / 50 0.3 – 9.3K 3.94 / 100 0.3 – 9.7K 5.91 / 150 0.3 – 8.6K 7.87 / 200 0.3 – 9.6K 9.84 / 250 0.3 – 9.3K 11.81 / 300 0.3 – 9.3K Tolerance: +/- 0.3K Values in this table are an approximation. Actual values will vary due to actuator configuration and construction.
PAGE 6
LINEAR ACTUATOR LIGHT DUTY SERIES Ordering Key LACT - V- Standard Stroke (nominal) 2 : 2” [ 50mm] 4 : 4” [100mm] 6 : 6” [150mm] 8 : 8” [200mm] 10 : 10” [250mm] 12 : 12” [300mm] Additional stroke lengths available Potentiometer P: Potentiometer Blank : No Potentiometer Input Voltage 12 : 12 VDC 24 : 24 VDC Gear Ratio 05 : 5:1 – Not available with “Q” option 10 : 10:1 – Not available with “Q” option 20 : 20:1 – Standard Gear Ratio 30 : 30:1 40 : 40:1 – Not available with “Q” option Not all gear ratios sto