Voyager Legend CS ® Bluetooth Headset System User Guide
Welcome Congratulations on purchasing your new Plantronics product. This guide contains instructions for setting up and using your Voyager Legend CS Wireless Headset System. Please refer to the separate safety instructions for important product safety information prior to installation or use of the product.
What's in the Box Base Headset Telephone interface cable Power supply Eartips Some models may also include: HL10 Lifter USB Charge cable 3
Base and Headset Basics Base 8 4 1 2 5 6 3 1 Call/mute LED 2 Power on/pairing LED 3 Charging LED 4 Pairing button 5 Power jack 7 9 10 6 Handset lifter/EHS cable jack 7 Telephone interface cable 8 Listening volume dial* 9 Speaking volume dial* 10 Configuration switch* *For installation set up Headset 1 2 3 4 5 1 Volume +/- button 2 Power button 3 Snap fit magnetic charge connection 4 Call button 5 Mute microphone/voice command button 4
Accessories Sold separately. 1 2 3 4 6 7 5 8 9 1 Portable charge case 2 Desktop charge stand 3 AC charger 4 USB charge cable* 5 Car charge adapter 6 Micro USB charge adapter 7 Eartip kit (available in S, M, L) 8 HL10 lifter* Automatically lifts handset and returns it to the cradle. Enables remote call control with your headset. 9 Electronic hookswitch cable (EHS cable) Electronically and automatically takes your desk phone handset off hook. Enables remote call control with your headset.
Fit Change the eartip Change the eartip for a better fit. 1 Push in eartip and rotate to the left to unlock it. 2 1 2 Align new eartip into slot. 3 Rotate it to the right to lock it into place. 2 1 Wear on the left or right To wear the headset on your other ear, rotate the boom upwards then twist it around so the eartip is on the other side before lowering the boom.
Connect Your Desk Phone Connect the power Plug one end of the power supply into the power jack on the back of the base and the other end into a working power outlet. The Power On LED will be solid white. Charge the headset Place the headset in the charge cradle. The charging LED on the base will flash blue when charging and turn solid blue when the headset is fully charged. Charge for at least 20 minutes prior to the first use. A full charge takes 90 minutes.
NOTE If you will be using a standard desk phone set up or a desk phone with an HL10 lifter, continue below. If you will be using the desk phone with an EHS cable, refer to Desk phone plus EHS cable section in this guide. For further installation information refer to the EHS Getting Started guide that came with your EHS cable or at plantronics.com/accessories. Desk phone (standard) 1 Connect one end of the telephone interface cable to the back of the base.
3 Remove the handset from the desk phone cradle. 4 While wearing your headset, press the call button on the headset. 5 If you do not hear a dial tone, adjust the configuration switch (A-G) until you do. NOTE For most phones, these factory settings will sound best. 6 Dial a test call from the desk phone. If needed, fine tune the volume with the headset volume controls. You can also adjust the desk phone speaking and listening volumes on the bottom of the base.
3 Desk phone plus EHS cable Slide the lifter up to where it nearly touches the handset earpiece. 4 Press the call button on your headset to activate the lifter. 5 If you hear a dial tone the lifter is set correctly and needs no adjustment. 6 Remove the protective strips from the 3 mounting tapes on the underside of the lifter. 7 Gently place the lifter on the desk phone in the pre-determined position. 8 Press firmly to adhere.
Position your base The minimum recommended separation between your desk phone and the base is 6 inches. The minimum recommended separation between the base and computer is 12 inches. Incorrect position can cause noise and interference problems.
Headset Overview Headset Controls voice Call button Volume button Headset LED (indicator light) Power button Magnetic charge port Mute button Talk time Adjust the volume Out of range indications Voice button (mobile phone use only) Play/Pause button (mobile phone use only) With a single full charge, the Voyager Legend CS will provide up to 7 hours of talk time and up to 11 days of standby time. Toggle the Volume button (show icon) up (+) or down (-) during a call to adjust the volume.
When you return to the operating range of the base or mobile phone, a voice prompt will announce: • "Phone 1 Connected"; audio restored if active NOTE Note: If both desk phone and mobile phone are connected to the headset it will be announce "Phone 1 Connected" and "Phone 2 Connected" as connections restored.
Base LEDs 1 2 3 1 Call Status LED Idle = Unlit Incoming call = fast blue flash On call = solid blue Call (headset mic) muted = slow blue flash 2 Power On/Pairing LED Power off = unlit Powered = solid blue (headset paired/connected) Powered = solid red (headset not paired or disconnected) In pairing mode = red/blue flashing Pairing successful = solid blue 3 Headset Battery LED (when docked) Full battery, charging stopped = solid blue High, charging = 3 blue flashes every 10 seconds Medium, charging
Your Base : Pairing Pairing your base to your headset Bluetooth pairing button Pairing headset The headset and base that came in the box are already paired to each other. However, if you wish to use a new headset or need to restore subscription to your current headset, the units can be paired to each other by doing the following. 1 Press and hold the Bluetooth pairing button until the power LED (middle) flashes RED/BLUE.
5 Once successfully paired, LEDs stop flashing red and blue. The LED remains solid blue and you hear “pairing successful.” NOTE To enable caller name announcement, allow access to your contacts if your phone prompts you.
Call Controls - Desk Phone Place a call Answer a Call 1 Wearing the headset, press the Call button 2 Remove the handset from the cradle, you will hear dial tone. This step will be automatic if you install a handset lifer or EHS cable accessory. For a complete list of accessories, visit www.plantronics.com/accessories 3 Dial the number using your desk phone.
Call Controls - Mobile Phone Place a call Answer a call Reject a call 1 Wearing the headset, press the Call button 2 Dial the number using mobile phone. 3 To end the call, press the Call Button 1 If wearing your headset press Call Button 2 If wearing the headset and prompted, "Incoming call, answer or Ignore", say "Answer", or 3 If not wearing your headset, place the headset on your ear; the call will be answered automatically.
Customize Your Headset Your headset understands and speaks in English. You can change the language and other settings online. MyHeadset™ Updater tool enables you to: • Receive firmware updates • Change language for voice alerts and commands (English U.K., French, German, and Spanish. Voice alerts are also available in Cantonese and Mandarin.
Features Listen to audio via A2DP Transmission range Simultaneous call handling behavior (PC Mobile) Your Voyager Legend headset can play media files (music, podcasts, navigation, etc.) from any A2DP (Advanced Audio Distribution Profile for Bluetooth)-enabled mobile device. Your Voyager Legend Bluetooth headset has a 10 meter effective range. Voice prompts from your headset will alert you if you lose connection with your base or mobile phone.
• "Cancel" • "Check battery" • "Ignore" • "Pair mode" • "Redial" • "What can I say" NOTE The voice-dial feature on your phone is initiated by pressing the Call button for 2 seconds. The voice-dial feature is not a headset voice command and only works with supporting phones. Disable the answer/ignore voice commands To disable the “answer/ignore” voice commands: 1 Switch on the headset. 2 Press and hold the Voice button until you hear a double tone. 3 Repeat to reactivate the voice answer commands.
Troubleshooting Headset Desk phone Talk time performance is significantly degraded even after a full recharge. Battery is wearing out. Contact us at www.plantronics.com/ support . I can’t hear a dial tone in the headset. Make sure your headset is charged. Make sure your headset is subscribed to base. See Subscription button. Press the call control button on your headset.
NEED MORE HELP? www.plantronics.com/support Plantronics, Inc. Plantronics BV 345 Encinal Street South Point Building C Santa Cruz, CA 95060 Scorpius 140 United States 2132 LR Hoofddorp © 2013 © 2013 Plantronics, Inc. All rights reserved. Plantronics and Voyager Legend are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Plantronics, Inc. is under license.
