User's Manual

ManualsBrandsPOLYCONCEPT HONG KONG ManualsElectronics900MHz 40 Channel Cordless Phone

Project#70001 – Retro Cordless Phone

Date: 12 July 2004

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of fire, electric shock and injury to persons, including the

following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not place this product on an unstable cart, stand or table. The product may

fall, causing serious damage to the product.

5. Slots and openings in the cabinet and the back or bottom are provided for

ventilation, to protect it from overheating, these openings must not be blocked or

covered. The openings should never be blocked by placing the product on a bed,

sofa, rug or other similar surface. This product should never be placed near or

over a radiator or heater. This product should not be placed in a built-in

installation.

6. Never push objects of any kind into this product through cabinet slots as they

may touch dangerous voltage points or short out parts that could result in a risk

of fire or electric shock. Never spill liquid of any kind on the product.

7. To reduce the risk of electric shock, do not disassemble this product, but take it

to a qualified serviceman when service or repair work is required. Opening or

removing covers may expose you to dangerous voltages or other risks. Incorrect

re-assembly can cause electric shock when the appliance is subsequently used.

8. Unplug this product from the wall outlet and refer servicing to qualified service

personnel in the following cases:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions as an improper adjustment of other controls may result in

damage and will often require extensive work by a qualified technician to

restore the product to normal operation.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance.

Summary of content (22 pages)

PAGE 1
Project#70001 – Retro Cordless Phone Date: 12 July 2004 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. 2. Read and understand all instructions. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
PAGE 2
9. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be damaged by persons walking on it. 10. Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 11. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 12.
PAGE 3
designed for wet locations. 3. Never touch uninstalled telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. CONSUMER INFORMATION This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
PAGE 4
NOTICE: If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this [equipment ID] does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes, are very destructive to telephone equipment connected to AC power sources.
PAGE 5
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier.
PAGE 6
14. Talk Button 15. Battery Contact Plate 16. Pause Button 17. Flash/Program Button 18. Mouth Piece Cover 19. Ringer On/Off Switch 20. Channel/Delete Button 21. Tone/Exit Button 22. Caller ID/Volume (σ and τ) Button 23. Redial Button 900-MHz Cordless Telephone with Caller ID IMPORTANT Charge the handset battery for 12 continuous hours prior to first use. INTRODUCTION Your 900-MHz Retro Cordless Telephone is a fine-quality home communications product.
PAGE 7
 Caller ID* and Caller ID with Call Waiting*  (*Each feature works with your telephone company. A subscription is required.) 40-number Caller ID list   10-name/number directory Receiver volume control   3-line trilingual display Ringer On/Off switch  Low battery warning *Important: To use all of the features of this phone, you must subscribe to either the standard Name/Number Caller ID Service or Caller ID with Call Waiting Service.
PAGE 8
other end into an electrical outlet. The Voice Mail/In-use/Charge Indicator (4) lights, verifying the battery is charging. Charge the handset battery for 12 continuous hours prior to first use. The initial battery charge is important for best performance. Low Battery Warning: When the battery is low you will hear a short beep every 7 seconds. Please follow the same steps as above to recharge your battery for best performance.
PAGE 9
English is factory set. 3. Use the handset number keys to enter the desired setting. For example, to choose French, press the number 2 key. 4. Press the Flash/Program Button (17) to store selection. You will hear a confirmation tone. Tone/pulse setting 1. Make sure the phone is off (not in TALK mode). 2. Press the Flash/Program Button (17) until 1 TONE 2 PULSE shows on screen. Tone is factory set. 3. Use the number keys to enter the desired setting.
PAGE 10
and press τ to decrease. VOL 1 is the lowest level and VOL 4 is the loudest. Making a call Press the Talk Button (14) before you dial and press it again to hang up. Redialing a call Press the Talk Button (14) and then the Redial Button (23) to redial the last number you dialed (up to 32 digits). If you get a busy signal, and want to keep dialing the number, just press the Redial Button (23) again (you do not have to turn the phone off and back on).
PAGE 11
with the Stutter Dial Tone type of VMWI system. Channel button Press and release the Channel/Delete Button (20) to advance to the next channel to get rid of static while talking. Temporary tone This feature enables pulse (rotary) service phone users to access touch-tone services offered by banks, credit card companies, etc. 1. 2. Call the bank’s information line. Press the Tone/Exit Button (21) after your call is connected. 3. 4. Follow the voice instructions to complete your transaction.
PAGE 12
from your phone company, you are able to see who is calling when you hear the call waiting beep. The caller information appears on screen after you hear the tone.  Press the Flash/Program Button (17) to put the first caller on hold and answer  the incoming call. Press the Flash/Program Button (17) again to return to the first caller.
PAGE 13
Caller ID number display  Use the CID/VOL keys to scroll to the phone number you want to store or call.  Press the Format Button (13) to change to the required number of digits. The Format Button (13) lets you select how many digits of the number to be displayed. 7 7-digit telephone number. 10 3-digit area code + 7-digit telephone number. 11 Long distance code 1 + 3-digit area code + 7-digit telephone number. 2. 3. Press the Memory Butto n (12). Press the desired memory location number.
PAGE 14
2. Use the Caller ID/Volume (σ and τ ) Button (22) to display any Caller ID entry. 3. Press and hold the Channel/Delete Button (20) until the phone beeps and DELETE ALL? Shows on the screen. 4. Press the Channel/Delete Button (20) again to erase the entire list. You will hear confirmation tone and NO CALLS appears. DIRECTORY Store up to 10 names/numbers in the directory for quick dialing. The number can be up to 24 digits. The name can be up to 15 characters.
PAGE 15
number. You will hear a confirmation tone. Storing last-dialed number 1. Repeat steps 1 through 6 in Storing a name/numbe r in the directory. 2. Press the Redial Button (23). 3. Press the Memory Button (12) to store the number. You will hear a confirmation tone. Making calls from the directory 1. Make sure the phone is off (not in TALK mode). 2. Press the Memory Button (12). 3. Use the C aller ID/Volume (σ and τ ) Button (22) to scroll through directory until the desired name is shown. 4.
PAGE 16
how you can chain dial to make a call through a long distance service: The Number for: Long distance access number Authorization code Memory Location 7 8 Frequently called long distance number 9 1. 2. Make sure the phone is on. Press the Memory Button (12) and then press 7. 3. When you hear the access tone, press the Memory Button (12) again and then press 8. 4. At the next access tone, press the Memory Button (12) and then 9.
PAGE 17
2. Disconnect the battery plug from the jack in the compartment and remove the 3. battery. Insert the new battery and connect the cord into the jack. 4. 5. Put the battery compartment cover back on. Place handset on the base t charge. Note: If the handset battery is removed for more than 5 minutes, the directory memory and the Caller ID memory will be erased. Charge the handset battery for 12 continuous hours prior to first use.
PAGE 18
Prompt asking if you want to erase entire Caller ID list. DELETED Prompt confirming the Caller ID/Directory entry is erased. END OF LIST Indicates that there is no additional information in Caller ID list. NEW Indicates new caller(s) in the Caller ID list. UNKNOW NAME/CALLER/NUMBER The incoming call is from an area not serviced by Caller ID or the information was not sent. PAGING The Page Button (3) is pressed on the base. BLOCKED CALL The caller has blocked name/number from transmission.
PAGE 19
This appears for 60 seconds when you have just received a new voice mail. This message only appears if you subscribe to an answering service with your telephone company. MSG WAITING OFF Appears when Voice Mail has been reviewed.
PAGE 20
 Is the telephone line cord connected to the base and the wall jack? Disconnect the base from the wall jack and connect another phone to the same jack. If there is no dial tone in the second phone, the problem might be your  wiring or local service. Is the handset out of range of the base?   Make sure the battery is properly charged (12 continuous hours). Is the battery installed correctly?  Does the handset beep when you press the Talk Button (14)? The battery may need to be charged.
PAGE 21
 Did you reprogram directory after power outage or battery replacement? RECYCLING NICKEL -CADMIUM BATTERIES NICKEL-CADMIUM BATTERIES MUST BE DISPOSED OF PROPERLY (Drawing) Please take you used battery to a store that recycles Ni-Cd batteries. MAINTENANCE To keep your telephone working, follow these guidelines:  Avoid putting the phone near heating appliances and devices which generate electrical noise (for example, motors or fluorescent lamps).   Do not expose to direct sunlight or moisture.
PAGE 22
Phone: 1-800-358-8122