Assembly Instructions

ManualsBrandsPolygroup Trading ManualsElectronicsRemote Controller

*Electrical Rating For The Tree

(For Indoor Use Only)

Input: 120VAC, 60Hz, 0.38A

Output: 29V DC 0.621A

Fig. B - Tree and Light Assembly

Tree top

Section 2

Section 1

Top view

Side view

Fig. C

MODEL #: TG76M2AGMD11

1. Before you start to assemble your tree, choose an appropriate location near a wall outlet.

2. Assemble the tree stand and place on a level surface. (See Fig. A)

TREE ASSEMBLY INSTRUCTIONS

NEED HELP?

DO NOT RETURN TO STORE. PLEASE VISIT US AT:

www.polygroupstore.com OR 1-888-919-0070

Fig. A - Tree Stand Assembly

Unfold the legs and lay the

stand in a flat area. Then slide

the locking disc downward and

snap into place.

Please scan code to

learn how to shape

and set up your tree

Congratulations on purchasing your new tree from Polygroup®!

This tree comes with Quick Set® technology - allowing you to set up your tree and light it up in minutes!

Carefully follow the instructions below on how to quickly and easily set up your new tree.

3. Each tree section is numbered with a sticker. Please identify all sections before assembling.

4. Assemble the tree from bottom to the top. Start with the bottom section and remove the protective cap before inserting into the

assembled stand. Make sure the pole is firmly inserted and secured into the stand.

5. Continue by inserting the upper tree section(s) to the lower section(s) until inserting the tree top.

6. Allow branches to fall into place or gently pull up and out. When adjusting branches, be sure that all wires are free of branch hinges.

7. Insert green label extension cord into adapter and adapter insert into the wall outlet (See Fig. B), your entire tree should now be lit.

8. Begin to shape the branches and tips working from the bottom to the top. Start with tips farthest from the pole and fan out one to

the right, one to the left and one at the center of the main stem. (See Fig. C)

Adapter

To Be Plugged

Into Wall

Outlet

Insert Green

Label Plug

into Adapter

Align both arrows

in a straight line

before sliding

down to insert

Open the

cap cover

Do Not Tamper

Internal Parts

Summary of content (5 pages)

PAGE 1
NEED HELP? DO NOT RETURN TO STORE. PLEASE VISIT US AT: www.polygroupstore.com OR 1-888-919-0070 TREE ASSEMBLY INSTRUCTIONS Congratulations on purchasing your new tree from Polygroup®! This tree comes with Quick Set® technology - allowing you to set up your tree and light it up in minutes! Carefully follow the instructions below on how to quickly and easily set up your new tree. Please scan code to learn how to shape and set up your tree 1.
PAGE 2
9. After shaping the entire tree following the previous step, slightly upsweep all branch tips for a uniform look. Shift branches to fill any gaps. Your Christmas tree is now complete and ready to be decorated. STORAGE INSTRUCTIONS 1. Unplug the power adapter from the wall outlet first and then remove all ornaments and decorations. 2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove from section below and fold all branches toward the pole. 3.
PAGE 3
Battery Replacement 1. Loosen the screw of the battery cover with a screwdriver (not included). 2. Replace the used battery with a new CR2032 button cell battery (not included). Make sure that the battery is installed with the correct polarity (+ and -). 3. Retighten the screw to close and secure the battery cover. WARNING 1. This remote controller is powered by a lithium battery. Due to their small size, lithium batteries can easily be swallowed by children.
PAGE 4
IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. a) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
PAGE 5
FCC Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.