Instructions / Assembly

ManualsBrandsPOND BOSS ManualsFilters900 Gal. Pressurized Pond Filter

Pressurized Filter

Up to 900 gallons

ITEM #FP900

PACKAGE CONTENTS

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or

operate the product. Contact customer service for replacement parts.

• Estimated Assembly Time: 20 minutes

• Tools required for assembly: hacksaw.

Part

Description

Quantity

Tank

Cover

Lid

O-ring

Adapter

Gasket

Locking ring

Tube

Bio media balls

Small filter

Coarse filter

Fine filter

REMINDER

CALL 1-888-755-6750

BEFORE RETURNING TO STORE.

Questions, problems, missing parts? Before returning

to your retailer, call our customer service department at

1-888-755-6750, 8 a.m.-6 p.m., EST, Monday-Friday, or

email us at customercare@thepondboss.net. Or visit our

website www.thepondboss.net.

PLEASE CALL 1-888-755-6750 BEFORE RETURNING TO THE STORE.

WWW.THEPONDBOSS.NET

Summary of content (6 pages)

PAGE 1
Pressurized Filter Up to 900 gallons ITEM #FP900 REMINDER CALL 1-888-755-6750 BEFORE RETURNING TO STORE. Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-755-6750, 8 a.m.-6 p.m., EST, Monday-Friday, or email us at customercare@thepondboss.net. Or visit our website www.thepondboss.net.
PAGE 2
ASSEMBLY INSTRUCTIONS 1. Assemble the tube, gasket and adapter. Insert the adapter and gasket into the outlet of the tank (lower hole). Fix it in place with the locking ring. Fig. 1 Gasket Tube Adapter Locking ring Fig. 1 2. Place the bio balls into the bottom of the tank. Fig. 2 Bio balls Fig. 2 3. Place the fine filter pad inside the tank. Then place the coarse filter pad over the fine filter pad. Fig. 3 Coarse Filter NOTE: The coarse filter pad is black. The fine filter pad is blue.
PAGE 3
4. Insert the adapter and gasket into the inlet of the tank (upper hole). Fix it in place with the locking ring. Fig. 4 Locking ring Gasket Adapter Fig. 4 5. Turn over the cover and locate the groove. Place the o-ring into the groove. Notes: o-ring one side is flat, another side is round, must place the flat side down into the groove of cover, otherwise it will case leakage.( See detail view.) Fig. 5 D D B B Detail view Fig. 5 6. Place the cover (with the o-ring attached) over the top of the tank.
PAGE 4
7. Screw the lid onto the top of the tank. Make sure that it is secure, or the filter will leak. Fig. 7 Lid Tank Fig. 7 8. Connect a length of tube from the outlet of a pump to the inlet of the filter (upper hole). Connect a length of tubing from the outlet of the filter (lower hole) to a water feature. Fig. 8 NOTE: Pump and tubing is NOT INCLUDED. The adapter is compatible with 3/4 in. or 1 in. tubing. In Out Fig. 8 PLEASE CALL 1-888-755-6750 BEFORE RETURNING TO THE STORE. WWW.THEPONDBOSS.
PAGE 5
CARE AND MAINTENANCE • Occasional cleaning of the filter pads will be necessary to ensure the proper functioning of the system. The top filter pad is a coarse pad (black) and will catch larger particles. The bottom filter pad (blue) is a fine pad designed to trap smaller debris. Both pads should be removed and washed with clean water when they are visibly soiled. • Filter pads should be changed annually. The exterior surface of the filter box may also need occasional cleaning.
PAGE 6
LIMITED WARRANTY All pumps and electrical products are warranted to the user against defective material and workmanship, under normal working conditions. This warranty period begins on the date of purchase by the original purchaser. Unless otherwise specified all pond boss® electrical products are warranted to the user against defective material and workmanship, under normal working conditions for 1 year from the date of purchase. • Pond and Waterfall pumps are warranted for 3 years.