Instructions / Assembly

ManualsBrandsPOND BOSS ManualsFountain Spray HeadsLit Container Fountain Kit

PLEASE CALL 1-888-755-6750 BEFORE RETURNING TO THE STORE.

WWW.THEPONDBOSS.NET

Container Fountain Kit with LED

Light

ITEM #DCFKL

PACKAGE CONTENTS

WARNINGS AND CAUTIONS

WARNING

• Risk of electrical shock. This pump is supplied with a grounding conductor and grounding–type

attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly

grounded, grounding-type receptacle.

• Do not exceed the voltage shown on the pump.

• Always disconnect pump from the power source before beginning any maintenance or work on the

pump.

• Inspect cord for damage before installation and/or maintenance. Replace the entire pump assembly if

damage is found.

• Do not remove the grounding pin from the power cord plug.

• To reduce the risk of electric shock, use only on portable, self-contained fountains no larger than 5 ft. in

any dimension.

Part Description Quantity

A Pump with filter and LED light 1

B Extensions 4

C Extension tubes 1

D Waterspray nozzle 1

E Waterbell nozzle insert 1

F Trumpet nozzle insert 1

G Lower fountain head nozzle 1

H Epoxy putty (part A) 1

I Epoxy putty (part B) 1

J Cord holder 1

REMINDER

CALL 1-888-755-6750

BEFORE RETURNING TO STORE.

Questions, problems, missing parts?

Before returning

to your retailer, call our customer service department at

1-888-755-6750, 8 a.m.-6 p.m., EST, Monday-Friday, or

email us at customercare@thepondboss.net. Or visit our

website www.thepondboss.net.

Summary of content (8 pages)

PAGE 1
Container Fountain Kit with LED Light ITEM #DCFKL REMINDER CALL 1-888-755-6750 BEFORE RETURNING TO STORE. Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-755-6750, 8 a.m.-6 p.m., EST, Monday-Friday, or email us at customercare@thepondboss.net. Or visit our website www.thepondboss.net.
PAGE 2
• Risk of electrical shock – This pump has not been investigated for use in swimming pools or marine areas. CAUTION • This pump has been evaluated for use with water only. • Use a proper power source as indicated on the pump label. • Keep the cord away from high temperatures or other heat sources. • Do not pump heated liquids. • Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling. • Operate in freshwater only.
PAGE 3
. Choose a container for your fountain kit. Fig. 3 Fig. 3 4. If the container is not already watertight, use a plastic liner. Or if a clay pot is used, spray the inside of the pot with a clear acrylic sealant. Be sure to use a sealant that is safe for clay pots. Wait 24 hours for the sealant to dry before filling the container with water. Fig. 4 Liner Fig. 4 5. Test fit the assembled container fountain kit in the container.
PAGE 4
7. Place the pump inside the container and run the cord though the newly drill hole. Seal the hole around the cord with epoxy putty and allow it to harden. Fig. 7 NOTE 1: Wearing gloves when mixing the putty is recommended. NOTE 2: For best adhesion, clean and roughen bond area. NOTE 3: Cut off required epoxy putty. Twist and knead until a uniform color is achieved (no streaks). Apply to the hole around the cord. Working time is 15 minutes until hardening begins. After approximately 1.
PAGE 5
11. Use the cord holder to tie a loop in the cord. This will help the pump stay in place. Fig. 11 Fig. 11 MAINTENANCE PROCEDURE 1. Unplug the pump, and remove it from the container. Fig. 12 Fig. 12 2. Remove the fountain head and extension tube. Turn over the filter box assembly. Open the filter housing by pushing on the sides of the housing. As you press on the sides of the filter housing, the top and bottom will unlock. Fig. 13 Fig. 13 3. Pull off the cover and remove the filter pad.
PAGE 6
4. Disassemble the pump and clean the internals of the pump. Fig. 15 Fig. 15 5. Reassemble the pump and filter box kit. Fig. 16 Fig. 16 CARE AND MAINTENANCE • Regular cleaning of the pump may be necessary depending upon the environment in which it is operated. Clean the pump when it is visibly soiled or when a drop in performance is detected. • Before cleaning, always disconnect the pump from the power source. • Remove all parts from the pump and clean in warm, soapy water.
PAGE 7
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-888-755-6750, 8 a.m.-6 p.m., EST, MondayFriday, or email us at customercare@thepondboss.net.
PAGE 8
LIMITED WARRANTY All pumps and electrical products are warranted to the user against defective material and workmanship, under normal working conditions. This warranty period begins on the date of purchase by the original purchaser. Unless otherwise specified all pond boss® electrical products are warranted to the user against defective material and workmanship, under normal working conditions for 1 year from the date of purchase. • Pond and Waterfall pumps are warranted for 3 years.