Owners Manual For Model PACJS1600 READ AND SAVE THESE INSTRUCTIONS
TABLE OF CONTENTS Introduction............................................................................... 1 How to Safely Operate your new Jetstream unit...................... 1 Setting up your new Port-A-Cool Jetstream™ 1600................ 2 How to Operate your new Port-A-Cool Jetstream™ 1600....... 3 How to Maintain Your Port-A-Cool Jetstream™ 1600............ 3 Jetstream™ unit Operation Warning......................................... 4 How to Maintain the Küül® pads media...........................
INTRODUCTION Evaporative cooling works on the principle of heat absorption by moisture evaporation. Simply put, heat is removed from the air as water evaporates. You feel this principle in action when you step out of a swimming pool or shower and feel immediately cooler as water evaporates from the surface of your skin. Your evaporative cooler works on the same principle. Hot outside air is pulled through water-saturated pads, where the air is cooled by evaporation and then discharged from the cooler.
SETUP INSTRUCTIONS The Port-A-Cool Jetstream™ 1600 model is pre-assembled and ready to operate. Simply remove the packaging and then carefully roll the unit from the box. Connecting to water. Move the cooler to an area where it can be filled with water and drained. The cooler should be located on level ground. Connect to a water supply using a commercial grade garden hose (supplied by customer). Simply attach the hose to the adapter located on the left side of the unit (see figure 1).
OPERATING INSTRUCTIONS Make sure the two locking casters have been locked to prevent the cooler from moving before turning on the fan. Turn on the water supply to the cooler. The hose connection to the float valve provides an automatic method of refilling the water supply as water is evaporated. For best results, turn the pump on a few minutes before turning on the blower fan. This allows the cooling pads to pre-wet for best efficiency.
2) Roll up the electrical power cord and secure it to ensure that it will not be rolled over, tripped over or caught in equipment. NOTICE: POWER CORD MAY BE REPLACED ONLY BY THE MANUFACTURER OR QUALIFIED AGENT!! 3) Cover the Port-A-Cool Jetstream™ 1600 unit completely to prevent dust build-up and store in a dry area. This also helps prevent damage to the pads. Optional dust covers are available from your distributor.
KÜÜL® PAD MAINTENANCE Periodic draining of the pump will help reduce the build-up of calcium deposits on the pad and pad frame. Periodic cleaning of the pads will also help increase the life of the pads and the cooling performance of the cooler. Do not attempt to clean the pads while they are installed in the pad frames or in the cooler.
TROUBLESHOOTING The following troubleshooting guide is intended to address the most common symptoms which may occur. If you are unable to resolve the issue, please call Technical Support. Turn off all power to the cooler before attempting to troubleshoot any of the following symptoms. SYMPTOM POSSIBLE CAUSES REMEDY Unit fails to start or deliver air 1. No electrical power to unit 1. Check power A. Fuse blown A. Replace fuse* B. Circuit breaker tripped B. Reset breaker* C.
Port-A-Cool, LLC PAGE 7 PORT-A-COOL JETSTREAM™ OWNERS MANUAL
Jetstream LIMITED WARRANTY 1-YEAR LIMITED WARRANTY Port-A-Cool, LLC, Center, Texas, extends this limited warranty to the original purchaser of a Port-A-Cool Jetstream™ Evaporative Cooler operated under normal conditions within the continental United States. I. One Year Coverage applies to all components and accessories furnished by Port-A-Cool, LLC.
HOW TO CONTACT TECHNICAL SUPPORT Technical support and service is available directly from your distributor or call Port-A-Cool® Technical Support Hotline at 888-266-5243 (888-COOL-AID) for the distributor nearest you. You may also contact the Support Hot Line for consultation on parts replacement. Please have serial number and model number of unit available. REPLACEMENT PARTS A.
For warranty replacement parts call Port-A-Cool® Technical Support at 1-888-266-5243. FAX: 936-598-1431. Shipping Address Port-A-Cool, LLC 721 FM 2468 at Henrietta Road Center, Texas 75935 PAGE 10 Mailing Address: Port-A-Cool, LLC P.O.
ITEM# PART # DESCRIPTION ITEM# PART # DESCRIPTION 1 BASE-JS/VT CASTER BASE ASSEMBLY FOR JS/VT 20 POWERCORD-02 10FT POWER CORD W/DOME STRAIN RELIEF 2 BLADE-ASSM-08 JS/VT 16" BLADE 21 PAC-PLB-01 INLET HOSE ADAPTER 3 BONNET-03 SPRAY BAR BONNET FOR 16" PAC 22 PAD6024/G 16" PAC REPLACEMENT PAD 4 BOX-UL-03 VAR SPD ELECTRICAL BOX 23 POLY-FTG-06 90DEG FITTING FOR SIGHT TUBE 5 CASTERS-JS-4 4" JS/VT NON-LOCKING CASTER 24 PRES-REG-01 INLET WATER REGULATOR 6 CASTERS-JS-4L 4" JS/VT
Port-A-Cool® Products and Accessories and Küül® Pads Cooling Media are manufactured by Port-A-Cool, LLC P.O. Box 2167 • 709 Southview Circle • Center, TX 75935 Phone 936-598-5651 • 800-695-2942 www.port-a-cool.