Use and Care Manual

ManualsBrandsPORTAMATE ManualsTools & HardwarePBR-001 Wood Storage Organizer Rack

PortamatePBR‐001WoodRack

ThePortamateWoodRackiscompactstoragesystemdesignedtohelpyou

organizeyourworkshop.Itcanbeusedforavarietyofmaterialsincluding

timber,moldings,pipes,PVCandmore.Applicationsincludegaragewalls,

basements,sheds,andevenoutdoorfences.

• TheWoodRackprovides6levelswithacapacityof110lb.(50kg.)perlevel.Itiseasy

toinstallandeasytocustomize.Seeinstructionsandillustrationsonbackofbox.

• Duetoproductimprovements,actualproductmayvaryslightly.MadeinChina.1year

warranty.

CONTENTS:

A:Screws(12)B:VerticalBars(2)C:HorizontalBars(12)D:Spacers(6)

WARNING:Ensureyourmountinglocationiscapableofwithstandingtheadditionalload.

Neveroverloadyourrack.Followtheassemblyandmountinginstructionsonbackofbox.

AssemblyInstructions:

1. Note:Verticalbarscanbeusedastemplatestomarkyourdrillinglocations beforeassembly.



Step1:Locatethebottomofthelongverticalbar.Ithasasmallscrewhole½inch(13mm.)

fromtheend.Insertascrew(A).Locatethebottomofanorangehorizontalbar.Ithasasmall

notch(B)asshownintheinsetphoto.Slidetheorangebardownthelengthoftheverticalbar

fromthetopuntilitrestsinpositionagainstthescrew.



Summary of content (5 pages)

PAGE 1
Portamate PBR‐001 Wood Rack The Portamate Wood Rack is compact storage system designed to help you organize your workshop. It can be used for a variety of materials including timber, moldings, pipes, PVC and more. Applications include garage walls, basements, sheds, and even outdoor fences. • • The Wood Rack provides 6 levels with a capacity of 110 lb. (50 kg.) per level. It is easy to install and easy to customize. See instructions and illustrations on back of box.
PAGE 2
. Step 2: Insert a screw into the next hole up, then slide another orange bar into position. Continue this process until all the bars are fitted, being careful that all the notches face down. Repeat this process for the other side. Note: Alternative rack positions can be achieved by drilling additional holes where desired using a 3/32” (2.5mm) drill bit. 3. Step 3: Installing to drywall or other paneled wall sheeting: Locate a solid structural support for your Portamate Wood Rack is very important.
PAGE 3
4. Step 4: Position the Spacers (C) behind the mounting holes, and fasten to the wall using the fasteners (not included) described in the recommended installations. Note: Customizing your Portamate Wood Rack is easy and practical to solve your workshop storage needs. Recommended Installations: 1. See Step 3 for drywall or other paneled wall sheeting. 2. Installing on masonry walls: Use ¼” (6mm) masonry anchors. The assembled wood rack is 1 5/8” (41 mm.) thick so a suitable length of anchor is 2 ¾” (71 mm.
PAGE 4
. Installing on wood fence: Structural reinforcement of the fence section is required because it was not designed to carry a load. This can easily be achieved by installing the proper horizontal supports between fence posts and then using vertical supports as shown. The assembled wood rack is 1 5/8” (41 mm.) thick so a suitable length of fastener is 2 ¾” (71 mm.) and ¼” (6 mm.) diameter.
PAGE 5
Customizing Your Wood Rack: 1. For Outdoor Use: Weather protection of your materials is achieved by creating a custom cover. Anchor a horizontal board the length of your material above the wood rack. Take sheet of vinyl or thick plastic and attach several thin wood battens to the inside with staples to keep it from flapping around. The batten at the top is used to screw it to the anchor board. Reinforcing strips can be glued in to avoid puncture from the horizontal rack bars. 2.