ESPAÑOL: PÁGINA 23 FRANÇAISE : PAGE 43 Instruction manual Double Insulated Plate Joiner MODEL 557 To learn more about Porter-Cable visit our website at: http://www.porter-cable.com IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . .6 CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 FUNCTIONAL DESCRIPTION . . . . . . . . .
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury.
GENERAL SAFETY RULES* Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
GENERAL SAFETY RULES* continued d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
ADDITIONAL SPECIFIC SAFETY RULES 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Wait for the cutter to stop before setting the tool down. An exposed cutter may engage the surface leading to possible loss of control and serious injury. 3.
SYMBOL V ........................ A ........................ Hz ........................ W ........................ kW ........................ F ........................ µF ........................ l ........................ g ........................ kg ........................ bar ........................ Pa ........................ h ........................ min ........................ s ........................ n0 ........................ …/min or …min-1 .........
MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating. Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C. only on D.C. current.
FUNCTIONAL DESCRIPTION FOREWORD Model 557 is designed to cut the grooves required for Porter-Cable biscuit sizes “FF”, “0”, “10”, and “20”. Adjustments are also provided which allow the tool to cut grooves for the following plate joiner accessories sold by other manufacturers: #6 biscuits, Duplex accessories, and Simplex accessories. ASSEMBLY NOTE: This tool is shipped completely assembled. No assembly time or tools are required. SELECTING THE BISCUIT Biscuits are 5/32" thick.
B A Fig. 1 ADJUSTING DEPTH OF GROOVE A “quick set” depth adjusting turret (A) Fig. 2, provides for quick changes in depth of cut to accommodate the various sizes of available biscuits and other accessories. To set depth of cut: rotate depth adjusting turret until desired size marking on turret aligns with the index mark (B) Fig. 2.
3. While holding adjustment knob in desired position: tighten lock-nut firmly. ADJUSTABLE FENCE Model 557 is equipped with an integral, adjustable fence which: • Provides micro height adjustment, distance scale includes indexes to top of cut, to center of cut, and to bottom of cut. • Tilts 0° through 135°, with an adjustable stop at 90°. • Does not have to be removed to make “flush” cuts. Height Adjustment (see Figs. 4 & 5) 1.
60 degrees 0 degrees C F A B A B E E Fig. 6 Fig. 7 90 degrees D 135 degrees C C A D A E E Fig. 8 Fig. 9 FINE ADJUSTMENT (90° Position) The adjustable 90° stop is factory adjusted for 90° and should not require additional adjustment. If “fine tuning” of the stop position is required: use a 5 64" hex wrench (not furnished), to rotate set-screw (F) Fig. 6, as required.
A B Fig. 11 Fig. 10 8. Continue to hold spindle lock button while using the hex wrench (furnished with tool), to tighten blade retaining bolt securely, (by rotating clockwise). 9. Rotate the “quick set” depth adjusting turret (A) Fig. 12, to the “FF” position. 10. Lift safety lever (A) Fig. 13, fully retract the plunge mechanism, and reposition the safety lever as shown in Fig. 14. Slowly release pressure on plunge mechanism. 11.
ALIGNMENT PLATE (For Narrow Stock) When joining narrow material, it will be necessary to install the alignment plate (A) Fig. 15, (furnished with tool). The alignment plate provides added support for narrow material, and has index marks to aid in centering the cut in the narrow material. Index marks are provided for 11/2" wide, and 2" wide material. Install alignment plate as follows: DISCONNECT TOOL FROM POWER SOURCE. 1. 2. Align alignment plate with fence (see Fig. 15).
A B C Fig. 18A Fig. 18 ATTACHING DUST BAG Depress spring clips (A) Fig. 18, and clip dust bag (B) on end of dust/chip deflector (C). The bag is equipped with a zipper to ease emptying of the collected material. Vacuum Hose A standard 1" vacuum hose can be attached to the dust port to provide a means for connecting the tool to your vacuum cleaner or dust collection system. “DUPLEX” HINGES The 557 can be used to make the mortises required for installing “duplex” hinges.
CORNER JOINT M I T E R J O I N T SURFACE JOINT PRACTICE CUTS BUTT JOINT After each set-up or adjustment to the tool, it is recommended you make several practice cuts in scrap material to verify desired operation. CORNER JOINTS 1. 2. 3. 4. 5. 6. Layout groove positions as described in POSITIONING GROOVES. Set depth stop turret to desired biscuit (or other accessory), size. Set the tilt fence to the 90° position (see ANGLE ADJUSTMENT Section of this manual).
7. Hold tool firmly as shown in Fig. 21, squeeze trigger switch to start tool. 8. At a slow, steady pace, push tool forward in base as far as depth stop allows. 9. Release trigger switch to stop tool and remove tool from work. 10. Repeat steps 6 through 9 until all the grooves for this joint are completed. Fig. 21 NOTE: Assemble all joints and verify alignments before applying glue (see Fig. 22). Fig. 22 SURFACE (“T”) JOINTS 1. 2. 3. 4. 5. 6. 7.
8. At a slow, steady pace, push tool forward in base as far as depth stop allows. 9. Release trigger switch to stop tool and remove tool from work. 10. Repeat steps 5 through 8 until all the grooves in workpiece “A” are completed. 11. Follow steps 3 through 10 of CORNER JOINTS Section to complete required grooves in workpiece “B” Fig. 23. NOTE: Assemble all joints and verify alignments before applying glue (see Fig. 26). C D Fig. 25 Fig.
7. Hold tool firmly as shown in Fig. 28, and squeeze trigger switch to start tool. 8. At a slow, steady pace, push tool forward in base as far as depth stop allows. 9. Release trigger switch to stop tool and remove tool from work. 10. Repeat Steps 5 through 8 until all the grooves for this joint are completed. NOTE: Assemble all joints and verify alignments before applying glue (see Fig. 29). Fig. 29 Fig.
TROUBLESHOOTING For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665. MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air.
SERVICE REPLACEMENT PARTS When servicing use only identical replacement parts. For a service parts list or to learn more about Porter-Cable visit our website at www.porter-cable.com SERVICE AND REPAIRS All quality tools will eventually require servicing, or replacement of parts due to wear from normal use. For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Customer Care Department at 1-800-487-8665.
WARRANTY PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) (CENTRE DE SERVICE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Power Tools are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) (Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien) ARIZONA Tempe 85282 (Phoenix) 2400 West Southern Avenue Suite 105 Phone: (602) 437-12