Product Manual

ManualsBrandsPorter-Cable ManualsNetwork Router9690LR

The following are PORTER-CABLE trademarks for one or more power tools and accessories: a gray and black color

scheme; a

“four point star” design; and three contrasting/outlined longitudinal stripes.

DEFINITIONS - SAFETY GUIDELINES

indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

indicates a potentially haz ard ous situation which, if not avoided,

may result in minor or mod er ate injury.

NOTICE

used without the safety alert symbol indicates potentially

hazardous situation which, if not avoided, may result in property damage.

To reduce the risk of injury, read the instruction manual.

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and all instructions Failure to follow

the warnings and instructions may result in electric shock, fire and/or

serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

• Hold power tool by insulated gripping surfaces because the cutter may contact its

own cord. Cutting a “live” wire may make exposed metal parts of the tool “live” and shock the

operator.

• Use clamps or another practical way to secure and support the workpiece to a stable

platform. Holding the work by your hand or against the body leaves it unstable and may lead

to loss of control.

• Metal cutting with router: If using router for metal cutting, clean out tool often. Metal

dust and chips often accumulate on interior surfaces and could create a risk of serious injury,

electrical shock or death.

• Never run the motor unit when it is not inserted in one of the router bases. The motor

is not designed to be handheld.

• Keep handles dry, clean and free from oil and grease. This will enable better control of the

tool.

• Maintain a firm grip with both hands on the tool to resist starting torque. Maintain a firm

grip on the tool at all times while operating.

• Keep hands away from cutting area above and below the base. Never reach under the

workpiece for any reason. Keep the router base firmly in contact with the workpiece when

cutting.

• Never touch the bit immediately after use. It may be extremely hot.

• Be sure that the motor has stopped completely before you lay the router down. If the

bit is still spinning when the tool is laid down, it could cause injury or damage.

• Be sure that the router bit is clear of the workpiece before starting the motor. If the bit

is in contact with the workpiece when the motor starts, it could make the router jump, causing

damage or injury.

• Always follow the bit manufacturer’s speed recommendations as some bit designs

require specific speeds for safety or performance. If you are unsure of the proper speed

or are experiencing any type of problem, contact the bit manufacturer.

• Do not use router bits with a diameter in excess of 2-1/8" (29 mm) in this tool.

• Do not hand-hold the router in an upside-down or horizontal position. The motor can

separate from the base if not properly attached according to the instructions.

• Before starting the motor, check to see that the cord will not snag or impede the rout-

ing operation.

• Keep cutting pressure constant. Do not overload motor.

• Provide clearance under workpiece for bit when through-cutting.

• Tighten collet nut securely to prevent the bit from slipping.

• Never tighten collet nut without a bit.

• Always make sure the work surface is free from nails and other foreign objects. Cutting

into a nail can cause the bit and the tool to jump.

• Always keep chip shield (if included) clean and in place.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long

hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size. The

following table shows the correct size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the

cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than

AWG

0 6 18 16 16 14

610 18161412

10 12 16 16 14 12

12 16 14 12 Not Recommended

ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

Always wear proper personal hearing protection that conforms to ANSI S12.6

(S3.19) during use. Under some conditions and duration of use, noise from this product may

contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions are

as follows

V ..................... volts A.........................amperes

Hz ................... hertz W .......................watts

min .................minutes

or AC ............alternating current

or DC .....direct current or AC/DC .....alternating or direct current

...................Class I Construction

o .......................no load speed

.......................

(grounded) n .........................rated speed

................... Class II Construction .......................earthing terminal

(double insulated)

........................safety alert symbol

…/min ............per minute BPM ...................beats per minute

IPM.................impacts per minute RPM ...................revolutions per minute

SPM ...............strokes per minute sfpm ...................surface feet per minute

SAVE THESE INSTRUCTIONS

MOTOR

Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than

10% will cause loss of power and overheating. PORTER-CABLE tools are factory tested; if this tool

does not operate, check power supply.

COMPONENTS (Fig. 1–19)

Never modify the power tool or any part of it. Damage or personal injury could result.

A. Motor clamp (1001 base)

B. Motor lower pins

C. Adjustment ring

D. Index line

E. Base

F. Motor Unit

G. Mounting screws

H. Subbase

I. Collet nut

J. Motor clamp (6931 base)

K. Motor clamp screw (6931 base)

L. Lock washer and flat washer (6931 base)

M. Motor clamp nut (6931 base)

N. Locking plate (6931 base)

O. Pins (6931 base)

P. Slots (6931 base)

Q. Wrench

R. Depth rod locking knob (6931 base)

S. Turret stop (6931 base)

T. Depth indicator (6931 base)

U. Depth indicator knob (6931 base)

V. Depth rod (6931 base)

W. Three turret stops (6931 base)

X. Fixed turret stops (6931 base)

Y. Short turret stops (6931 base)

Z. Locking lever (6931 base)

AA. Lower limiting nut (6931 base)

BB. Upper limiting nut (6931 base)

CC. Retaining screw (6931 base)

DD. Adjustment screw (6931 base)

EE. Clamp screw (6911, 1001 bases)

FF. Motor Switch

GG. Knob handles (6911 base)

HH. Outlet handle (6911 base)

II. Power cord (6911 base)

JJ. Lock button (6911 base)

KK. Trigger switch (6911 base)

LL. Zero line (6911 base)

MM. "D" Handle Grip

INTENDED USE

This heavy-duty router is designed for professional routing applications.

DO NOT use under wet conditions or in presence of flammable liquids or gases.

This is a professional power tool. DO NOT let children come into contact with the tool. Supervision

is required when inexperienced operators use this tool.

Instruction manual

Manuel d'instructions

Manual de'instrucciones

Part No. N384509 MAY2014

690 SERIES 1-3/4 PEAK

HP ROUTERS

SÉRIE 690 TOUPIES

DE 1-3/4 HP POINTE

SERIE 690 REBAJADORAS

DE 1-3/4 HP MÁXIMOS

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS

DE SERVICIO Y PÓLIZA DE GARANTÍA.

LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

690LR

691

693LRPK

9690LR

Summary of content (7 pages)

PAGE 1
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
PAGE 2
G F D C H B E A GG I GG A A FIG. 1 FIG. 2 FIG. 3 FIG. 4 K FIG. 7 O L N Q P M FIG. 5 FIG. 6 J FIG. 8 T W Z U R V Y S FIG. 9 FIG. 10 FIG. 11 X FIG. 11A B DD BB CC EE AA FIG. 12 FIG. 13 FIG. 14 II FF FIG. 15 D F C LL II HH KK JJ MM JJ FF MM EE GG GG KK FIG. 16 E OPERATION To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs.
PAGE 3
INSTALLING THE MOTOR (6911 "D" HANDLE BASE) 1. Loosen the clamp screw (EE) Fig. 15 to set the power unit in the base unit. 2. Insert the motor unit into the base aligning the lower pin (B) with the groove in the base. 3. Rotate the motor unit into the base clockwise until the motor switch (FF) Fig. 16 is directly above the knob handle (GG). 4. Connect the motor unit cord to the outlet in handle (HH) Fig. 16. 5. Continue rotating the motor unit into the base until upper guide pins set rigidly into base. 6.
PAGE 4
• • • • • • • • • • • • • • • jamais passer les doigts sous le matériau pour quelque raison que ce soit. S’assurer de bien maintenir la base de la toupie en contact avec la pièce lors de la coupe. Ne jamais toucher à la mèche immédiatement après l’avoir utilisée, car elle peut être extrêmement chaude. Attendre que le moteur s’arrête complètement avant de déposer la toupie. Le fait de poser l’outil alors que la fraise continue de tourner pose des risques de dommages corporels ou matériels.
PAGE 5
RACCORDEMENT À UNE SOURCE DE COURANT avant de connecter le cordon d’alimentation du bloc-moteur sur le secteur ou la poignée en D (le cas échéant), assurez-vous que l’interrupteur à bascule et la gâchette de la poignée en D sont sur la position ARRÊT. Tout démarrage accidentel comporte des risques de dommages corporels. REMPLACEMENT GRATUIT DE L’ETIQUIETTE Si les étiquettes d’avertissement deviennent illisibles ou sont manquantes, composer le (888) 8485175 pour en obtenir le remplacement gratuit.
PAGE 6
• Nunca toque las fresas después de utilizar la herramienta. Las fresas podrían estar sumamente calientes. • Asegúrese que el motor haya parado por completo antes de poner la herramienta. Si la broca sigue girando cuando la herramienta esté puesta a un lado, podría causar lesiones o daños. • Antes de encender el motor asegúrese que la fresa de la rebajadora no esté en contacto con el material de trabajo.
PAGE 7
PARA PONER EN MARCHA Y PARAR EL MOTOR Antes de poner la herramienta en marcha, despeje el área de trabajo de todos los objetos extraños. Compruebe que el cable no se enganche ni impida la operación de rebaje. Además sujete bien la herramienta para resistir el momento de arranque. Para evitar herida personal o daño a la obra, siempre deje que el motor PARE COMPLETAMENTE antes de poner el ráuter a un lado. Para poner el motor in marcha, mueva el interruptor de eje de balancín a "ON" o "I" coloque (FF) Fig.