2-1/2 inch (317 mm) Portable Planer Raboteuse portative de 317 mm (12-1/2 po) Cepillo Portátil de 317 mm (12-1/2 pulg.) Instruction manual Manuel d'instructions Manual de'instrucciones www.portercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
IMPORTANT SAFETY INSTRUCTIONS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed.
20. Never stand on the machine. Injury could occur if the tool tips, or if you accidentally contact the cutting tool. 21. Never leave the machine running unattended. Turn the power off. Don’t leave the machine until it comes to a complete stop. A child or visitor could be injured. 22. Turn the machine "OFF", and disconnect the machine from the power source before installing or removing accessories, changing cutters, adjusting or changing set-ups.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: GROUNDED OUTLET BOX CURRENT CARRYING PRONGS masonry products, and (CCA). Your risk from these exposures varies, depending on how often you do this type of work.
EXTENSION CORDS MINIMUM GAUGE EXTENSION CORD Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig.
UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol. A B 4 NOTICE Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine. After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.
OPERATION 11 10 STARTING AND STOPPING PLANER Make sure that the switch is in the "OFF" position before plugging cord into outlet. Do not touch the plug’s metal prongs when unplugging or plugging in the cord. 1. The on/off switch (A) Fig. 10 is located on the front of the planer moter. To turn the machine "ON", move the switch up to the "ON" position. 2. To turn the machine "OFF", move the switch (A) down to the "OFF" position.
15 16 A C B A B C 17 18 A A 19 20 E D F F B A KNIFE TRANSFER TOOL STORAGE 21 The knife transfer tool (A) Fig. 15, supplied with your planer, can easily be stored underneath the outfeed table extension (B) when not being used. A Velcro strip (C) is provided on the tool and underneath the table for this purpose. J WRENCH STORAGE The wrench (A) Fig. 16, can be stored in hole (B) located on the right rear side of the machine as shown. CARRYING HANDLE/STOCK TRANSFER BAR 1.
E 23 22 K D J F F H G O 25 24 C A B B 4. Insert knife transfer tool (G) Fig. 21, underneath center of knife. Lift the knife transfer tool up until knife (H) separates from pins (J) and pull out and remove knife as shown. NOTE: Knife transfer tool is magnetized, allowing it to attach to knife. 5. Rotate knife (H) Fig. 22 end-for-end, or using a new knife, position knife transfer tool (G) on top of knife as shown.
TROUBLESHOOTING 27 For assistance with your machine, visit our website at www.portercable.com for a list of service centers or call the help line at 1-888-848-5175. A MAINTENANCE To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury. KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air.
SERVICE THREE YEAR LIMITED WARRANTY REPLACEMENT PARTS Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our Customer Care Center at (888) 8485175. SERVICE AND REPAIRS All quality tools will eventually require servicing and/or replacement of parts.
