ITEM #0650198 HANGING LANTERN ® PORTFOLIO and PORTFOLIO & Design are trademarks or registered trademarks of LF, LLC. All rights reserved. TM MODEL #CP199MBK Français p. 11 Español p. 21 ATTACH YOUR RECEIPT HERE APPROVED FOR USE IN WET LOCATIONS Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.
TABLE OF CONTENTS Package Contents ............................................................................................................... 2 Hardware Contents .......................................................................................................................... 3 Safety Information ............................................................................................................... 3 Preparation ...........................................................................
HARDWARE CONTENTS (shown actual size) DD CC AA BB Wire Connector Machine Screw Connecting Chain Link Mounting Screw Qty. 3 Qty. 2 Qty. 2 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal.
SAFETY INFORMATION WARNING • All electrical connections must be in agreement with local codes and ordinances, the National Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your local codes, permits and/or inspections. Risk of fire - most dwellings built before 1985 have supply wire rated for 140°F. Consult a qualified electrician before installation.
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to install, operate or assemble the product.
ASSEMBLY INSTRUCTIONS 3. Attach mounting strap (C) to outlet box (not included) using the existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult with a licensed electrician before proceeding. Tighten machine screws (BB) completely to secure mounting strap (C).
ASSEMBLY INSTRUCTIONS 6. Determine the hanging length for fixture (H). Use pliers, a flathead screwdriver and a soft cloth (all not included) to open the link of chain (B) at length chosen. Remove any extra chain (B) at this time. 64 Screwdriver Feed wiring from fixture (H) up through chain (B) to pre-determined length. Soft Cloth Pliers B Wiring 7 7.
ASSEMBLY INSTRUCTIONS 9. Connect one of the wires from fixture (H) to the BLACK wire from outlet box using wire connector (AA). Connect the other wire from fixture (H) to the WHITE wire from outlet box using wire connector (AA). Connect BARE/GREEN wire from outlet box to BARE ground wire from fixture (H) using wire connector (AA). NOTE: If outlet box does not have a BARE/GREEN wire, the BARE ground wire from fixture (H) should be attached to the GREEN SCREW (labeled GND) on mounting strap (C).
ASSEMBLY INSTRUCTIONS 12 12. Attach shade (J) to fixture (H) using mounting screws (DD). Tightening mounting screws (DD) completely with a Phillips Screwdriver (not included). H Hardware Used DD Mounting Screw x2 DD DD J 13. Install one standard-base bulb (not included). Use a 60-watt max. incandescent bulb or CFL/LED equivalent. 13 CAUTION: When replacing bulb, please allow bulb and shade to cool down before touching. H Restore power and test fixture (H).
CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner on glass or fixture. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM Bulb will not light. POSSIBLE CAUSE 1. Bulb is burned out. 2. Power is OFF. 3. Faulty connection. CORRECTIVE ACTION 1. Replace light bulb. 2. Make sure power supply is ON. 3. Check wiring and all connections.