Installation Guide

ManualsBrandsPortfolio ManualsOutdoor Wall LightsIPA1691L-2

1 2 3 4 5 6

Lowes.com/portfolioLowes.com/portfolio

Lowes.com/portfolio

Lowes.com/portfolioLowes.com/portfolio

Portfolio is a registered trademark

Lowes.com/portfolio

Questions, problems, missing parts? Before returning to your retailer, call our

customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday -

Thursday, 8 a.m. - 5 p.m., EST, Friday.

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

EB1571

Portfolio is a registered trademark of

Français p. 7

Español p. 13

PACKAGE CONTENTS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS

ITEM #0616293

MODEL #IPA1691L

WALL LANTERN

LED chips will not light.

PROBLEM POSSIBLE CAUSE

1. Power is off.

2. Faulty wire connection.

3. Faulty switch.

Fuse blows or circuit breaker

trips when light is turned on.

Crossed wires or power wire is

grounding out.

Check wire connections.

3. Test or replace switch.

2. Check wiring.

1. Make sure power supply is on.

CORRECTIVE ACTION

TROUBLESHOOTING

WARRANTY

The manufacturer warrants all of its lighting fixtures against defects in materials and workmanship

for three (3) years limited from the date of purchase. lf within this period the product is found to be

defective in material or workmanship, the product must be returned, with a copy of the original

sales receipt as proof of purchase, in the original carton, to the place of purchase. The

manufacturer will, at its option, repair, replace or refund the original purchase price to the

consumer. This warranty does not cover fixtures becoming defective due to misuse, accidental

damage, improper handling and/or installation and specifically excludes liability for direct,

incidental or consequential damages. As some states do not allow exclusions or limitations on an

implied warranty, the above exclusions and limitations may not apply to you. This warranty gives

you specific legal rights. You may have other rights that vary from state to state.

CARE AND MAINTENANCE

• Shut off main power before cleaning light with damp cloth or window cleaner.

Do not use abrasive cleansers.

Printed in China

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m.,

EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

Fixture Body

Shade

PART DESCRIPTION PART #

0616293-A

0616293-B

0616293-C

0616293-D

0616293-AA

0616293-BB

Mounting Screw

Washer

Wire Connector

Outlet Box Screw

Strip 3/4 in. of insulation from fixture wire ends. Twist

stripped ends together with pliers (not included), black

to black (power), white to white (neutral). Snip ends.

Wrap the ground wire from the outlet box around the

green screw

preassembled on the mounting plate

(A), and then connect the ground wire from the

outlet box to the ground wire from the fixture.

Helpful hint: If the outlet box doesn’t have a ground

wire, you can attach the ground wire from the fixture

directly to the green screw on the mounting plate (A).

Attach wire connectors (BB) to ends. Tape wire

connectors (BB) and wires together with electrical

tape (not included).

Hardware Used

x 3

Wire Connector

Unscrew the cap nuts (D) and remove washers (C)

from mounting screws (B). Save for later use.

Separate the mounting plate (A) from wall plate of

fixture body (E).

AA BB

HARDWARE CONTENTS (shown actual size)

Outlet

Box Screw

Qty. 2

Wire

Connector

Qty. 3

3. Attach the mounting plate (A) to outlet box (not

included) using outlet box screws (AA).

Note: The

mounting screws (B) should protrude

out from the outlet box.

4. Attach and adjust shade (F) to the holes of fixture

body (E). Then, twist the shade (F) to fixture body

(E) until it is firmly secured.

Note: When twisting the shade (F) into fixture

body (E), hold the shade (F) with two hands.

Place fixture body (E) onto mounting screws (B),

securing with previously removed washers (C)

and cap nuts (D).

Hardware Used

x 2

Outlet Box Screw

Mounting Plate

Cap Nut

GND

PART DESCRIPTION

QUANTITY

D 2

E 1

Mounting Plate (preassembled to Fixture Body (E))

Mounting Screw (preassembled to Mounting Plate (A))

Washer (preassembled to Mounting Screw (B))

Cap Nut (preassembled to Mounting Screw (B))

CAUTION

• DO NOT touch the LED model/parts at anytime as this may cause damage to the fixture.

• Connect fixture to supply wires rated for at least 167˚F.

• Use only the supplied LED driver to power fixture.

SAFETY INFORMATION

WARNING

• Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear

gloves when handling the parts.

• Account for small parts and destroy packing material, as these may be hazardous to children

• Use flashlight or alternate light source to light work area during installation.

• Assistance may be required to support fixture during installation.

Please read and understand this entire manual before attempting to assemble, operate or install

the product.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

ASSEMBLY INSTRUCTIONS

Turn off power at circuit breaker or fuse panel.

Remove old fixture. Disconnect wiring.

PREPARATION

Before beginning installation of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble,

install or operate the product.

Estimated Assembly Time: 15 - 20 minutes

Helpful Tools (not included): Wire stripper, Level.

Tools Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers,

Wire cutters, Electrical tape, Safety goggles, Step ladder and Silicone caulking.

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Use silicone caulk (not included) to seal between

wall plate and wall.

CAUTION: Leave bottom unsealed so moisture can

drain out.

• Bulb Information: 12-watt integrated LED included; do not attempt to replace the LEDs.

CONSIGNES DE SÉCURITÉ