ITEM #0398487 #0398489 Portfolio® is a registered trademark of LF, LLC. All Rights Reserved. POST LANTERN MODEL #PL126BK #PL126WW Français p. 10 Español p. 19 ATTACH YOUR RECEIPT HERE Serial Number For Wet Location Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. 5 p.m., EST, Friday. EB15109 Lowes.
PACKAGE CONTENTS PART DESCRIPTION QUANTITY A Fixture 1 B Fixture Cover 1 C Spacer 2 D Shade 1 A C B D HARDWARE CONTENTS (shown actual size) AA E3 Wire Connector BB Mounting Screw Qty. 1 CC DD Decorative Nut Fixture Screw Qty. 3 Qty. 3 Qty. 3 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product.
SAFETY INFORMATION • If using this light fixture in a WET of DAMP location, this light fixture must be connected to a supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury, electrical shock or death. • DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded.
SAFETY INFORMATION CAUTION • TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off). • If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
ASSEMBLY INSTRUCTIONS 2. If applicable, remove existing fixture and disconnect all electrical wiring. 2 3. 3 Insert fixture screws (DD) into the three holes in outer edge on the underside of fixture (A). Tighten fixture screws (DD) with a Phillips screwdriver (not included). IMPORTANT: Fixture screws (DD) must be screwed completely into fixture (A) to ensure proper assembly later on. DD A Hardware Used DD Fixture Screw x3 DD Lowes.
ASSEMBLY INSTRUCTIONS 4a. Unwrap BARE wire from BLACK and WHITE wires on fixture (A). Prepare wire by stripping 3/4 inch of insulation from wire ends using wire strippers (not included). 4a 4b. Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (AA). Connect BLACK wire from fixture (A) to BLACK wire from outlet box using existing wire connector or wire connector (AA).
ASSEMBLY INSTRUCTIONS 6. Carefully push excess wiring and wire connectors (AA) inside top of post or pier base (neither included). 64 6 6 Place fixture (A) onto the mounting surface and secure with the mounting screw (BB). Hardware Used BB Mounting Screw A x1 BB 7. Align the three holes on underside of spacer (C) with the fixture screws (DD) in fixture (A). Push down on spacer (C) to secure in place. Repeat for the remaining spacer (C). 6 7 C DD C A 8.
ASSEMBLY INSTRUCTIONS 9. Align three posts on underside of fixture cover (B) with three fixture screws (DD) on fixture (A). Push down on fixture cover (B) until fixture screws (DD) come through holes in top of fixture cover (B). Secure fixture cover (B) to fixture (A) with decorative nuts (CC). 9 CC CC B IMPORTANT: If fixture screws (DD) are not visible through top of fixture cover (B), fixture screws (DD) have not been tightened completely.
CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean shade. Do not use an abrasive cleaner on shade or fixture. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM Bulb will not light. POSSIBLE CAUSE 1. Bulb is burned out. 2. Power is OFF. 3. Faulty connection. CORRECTIVE ACTION 1. Replace bulb. 2. Make sure power supply is ON. 3. Check wiring and all connections.