OPERATION MANUAL GPS&GPRS CAR ALARM GT3200ST
I. INTRODUCTION GPS GPRS Tracking and Alarm System utilize the GPS and car alarm functions in one unit. You can monitor the vehicle location and control the car alarm remotely. In addition, the unit will send event report if any trigger occurs. It has built-in 8 outputs and 9 inputs to perform essential alarm functions. 1.
The event trigger report is also configurable. User can turn on or off any event generated report from the PC setup program or via the air command. The event triggered report include (1) In-vehicle Door close/open (2) In-vehicle ignition on/off (3) Temperature range in/out the preset range (4) In-vehicle shock sensor trigger. The build in alarm (optional) trigger reports are also configurable and can be set from PC setup program or air command.
mode, the first 30 seconds countdown, The horn will sound once and parking lights will flash once every 10 seconds, after 30 seconds, horn will sound once and parking lights will flash once every 5 seconds, 30 seconds later, horn will sound and parking lights will flash once every 1 second. 60 seconds later, engine will not be able to start again (if starter cut relay connected). 4.
During the sleep mode, if any of the inputs are triggered, the system will wake up and send relevant reports to the server. The input triggers for waking the device up are selectable. When ACC is on, the system will back to working mode and stay connected to the TCP/UDP server in GPRS network. 1.15 2-STAGE SHOCK SENSOR (Optional) If car is lightly vibrated, siren will sound five times and parking light will flash five times to warn.
1. SMS send/receive 2. phone call 3. main unit information display Handset (Optional) 4. Immediate Geofence activate/deactivate 5. Help report sending 6. Duty on/off report 7. Emergency release Initialize the unit and program the device, including Network APN, server IP address, PC-setup user message, report control, and Geogence setting, etc … Note that Network APN and server IP details must be set before the installation.
Anytime the unit can call out and pick up phone call as well. to dial the number directly through the keypad. a. After dialing the telephone number, press button once or button〝Ⅰ〞of two button valet switch once dial out. If the dialing is successful, HAND FREE will ring, each time the button is pressed, the HANDFREE will chirp once as indication. Once the dialogist picks up the phone, the user can start talk with that person.
(6) Enter code learn mode or exit. ACC on and then press the button (the LED will be temporally stay off) and release it when the LED flashes 4 times. After releasing it, the horn will chirp three times to indicate system entered code learn mode; Turn ACC off to exit code learn mode and there is no sound for indication. (7) Enter valet mode or exit. ACC on and then press the button (the LED will be temporally stay off) and release it when the LED flashes 8 times.
B. Version No. Checking The below interface will last until correct UNIT Version No. is checked. (You should run this program before turn on power of UNIT) C. MAIN INTERFACE 1.
If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. IMEI: Any operate with ‘request or request all’ t after GPRS power on, the module series number will display automatically, otherwise it displayed with space. Set UNIT ID and UNIT password of for the device. Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters.
Set the SMS Number of the server. The unit will send reports to the server if GPRS connection is failed. AUTO GPS fix: the report will be display “A” in the report and indicate that if the number of satellite is more than 3 or equal to 3. If the number of satellite is less than 3, then it will show “L” in GPS fix section. 3D GPS fix only: the report will be display “A” in the report and indicate that if the number of satellite is more than 4 or equal to 4.
2.
Four Circular Geofence and one self-geofence: Circular Geofence must set origin and radius: Origin format :N2446.5321E12120.4231; N2446.5321 is latitude, E12120.4231 is longitude. Radius from 0.1 km to 1000km. User can set the reports send or local or ignore: Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports. Five rectangular geofence: Set two points position, the point format is N2446.5321E12120.
20 point Geo-fence areas can be set. When UNIT is out of these predefined zones, a report will be generated.
3. [Local report]: Automatic report can be configured in this section. To activate the function(s), please select “√” in checkbox and fill in data in the textbox.
The reports will be summarized as (1)Intelligent report Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed. Report when speed less than a preset value (refer the following 1.5 Km/Hr), and it will send stop report after a preset time (refer the following 120Sec). (min. speed is 0.1 km/Hr, max. speed is 1000 km/Hr).
(6)AD detect report (AD2) [on/off] SEND REPORT IF ADC2 LESS THAN [min voltage] V for [debounce time] SEC, RESEND PER [resend time] SEC [on/off] SEND REPORT IF ADC2 MORE THAN [max voltage] V for [debounce time] SEC, RESEND PER [resend time] SEC [on/off] SEND REPORT IF ADC2 GO UP [up voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC2 GO DOWN [down voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC2 ENTER/EXIT [min voltage] V TO [max voltage] V for [debounce time] SEC Note: AD2 input
You can select the crash report to be sent or not, while crash sensor over a preset value.(The crash sensor must be fit up, or the report still be ignored even if you select the item.) Otherwise the report will be ignored. (13) Tilt report Parameters: on/off, and degree If ACC off, then crash-sensor will work (if the Tangent angle sensor connected). crash-sensor can detect the little angle change. If the car be shake, then the crash-sensor will be triggered. And crash-sensor will wake up the system.
keep alive time is shorter then select this function will be OK.) This function is very useful while using UDP to prevent report lost. Send a keep alive packet right before a due reports if no data stream within certain time: Parameters: On/Off, and idle time. Some GSM provider might cut connection, if there is no data within certain time. It might result report lost in this “fake connection” duration. For example, you can set parameters in this region, ex 20 mins.
All the roam reports configured are same as Local report. Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports.
5. [Alarm REPORT setup] Alarm report(s) is also configurable. User can customize the events generated by the in-vehicle input or build in car alarm to be sent to the server. If the item(s) be selected (VALID), the related reports will be sent. Otherwise the report will be ignored even when an event is occurred internally. Also build in car alarm function can be set on here.
6. [Roam Alarm REPORT setup] In roam alarm mode, use can set all the alarm reports send or local or ignore: Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports. 7.
1) Roaming GPRS mode Use can configure roaming GPRS mode with automatic register or manual register in this field. When roaming GPRS mode in manual register, user can set 20 prefer operators, main unit will search and register from the 20 prefer operators. 2) Compress setting 1. 2. 3. 4. To send report in local GPRS, compressing N reports to a packet and then send out.(N: the digit between 1~8) To send report in roam GPRS, compressing N reports to a packet and then send out.
Electrical DC Supply voltage DC Tolerance voltage 12V or 24V 9V－36V Current (GPRS online) Current (GPRS transmission) Current (Peak) Current (Sleep) Internal Battery Battery type Battery capacity Charge type 60mA 80mA 120mA 25mA (GPS off) Ni-Mh 4.8V 80 mA/H Built-in charge circuit GPRS* Data provided by SIMCOM Frequency Range (MHz) Support 4-frequency 850/900/1800/1900 Channel spacing (Hz) 200 GPRS connectivity GPRS multi-slot class 10 GPRS mobile station class B SIM card interface 3.4~4.
Storage -40℃ to +85℃ Humidity Input voltage Current draw Average acquisition Tracking Antenna supply via VANT Voltage range Max. allowed current 4 Non-condensing 3.0 to 3.6 VDC 36mA (typical) 31mA (typical) Up to 5.2V 50mA Communication GPRS \SMS\RS232\RF (with optional build in alarm) Environmental Operating Temperature Storage Temperature -20°C to +55°C -40°C to +85°C Optional Accessories 1. Combined Antenna (with GPRS and active GPS) 2. Temperature sensor 3. Ultrasonic sensor 4. Shock-sensor 5.
OPTIONAL HANDSET OPTIONAL TEMPERATURE SENSOR OPTIONAL TEMP SENSOR HANDSET OPTIONAL CRASH SENSOR HANDFREE OPTIONAL CRASH SENSOR MIC PC SETUP OPTIONAL EXTERNAL RF ANT RESET H7 H8 H9 H10 H11 H12 H13 GT3200ST GREEN LED: GPS INDICATOR YELLOW LED: GSM INDICATOR RED LED: POWER INDICATOR H1 H2 H3 H4 H5 H6 GPS ANT GSM ANT VALET SWITCH LED 5A FUSE OPTIONAL SHOCK SENSOR RED BLACK 12V or 24V BATTERY II 2-KEYPAD I OPTIONAL BUZZER 12V OR 24V PURPLE -300mA OUTPUT OPTIONAL HORN RELAY RELAY BR
15.21 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
