User's Manual

2
When arm, there’s a 300mA negative output to disable engine, which has to be
connected a NC relay
AUTO RE-ARM (SEE SELECTION 10)
Siren sounds 30 sec upon triggering. Then, the system goes back arming again.
AUTO ARM AFTER TRIGERRING
Siren sounds 30 sec upon triggering. Then, the system will return arming mode
again. If the triggering signal exists still, the system will bypass this zone till it
returns to normal status.
PARKING LIGHTS EMERGENCY FLASH
In armed mode, parking lights and dome light will flash for 30 seconds if
triggered.
SIREN EMERGENCY SOUND
In armed mode, siren or car horn (See Function Selection 15) will sound for 30
seconds if triggered.
FUNCTION SELECTION
The function selection is programmable. Please follow the procedure.
a. Disarm the system.
b. Turn ignition from OFF to ON.
c. Press Valet switch 7 times within 10 sec.
d. Turn ignition OFF, then the LED will flash once per sec.
e. Press the switch the function numbers you would like to change within 20sec.
Each press will have one siren chirp for pressing confirmation. For entering
10 as a short cut, please press and hold switch for 3 sec, then siren chirp twice
for confirmation.
For example to enter 13, you can press and hold switch for 3 sec once, and
hear two chirps. Then, press switch three times with three chirps.
For example to enter 25, you can press and hold switch for 3 sec once,
and hear two chirps. Then, again press and hold switch for 3 sec once,
and hear two chirps. Then, press switch one by one 5 times. And, you’ll
hear 5 chirps totally.
f. Then, turn ignition from ON to OFF. You’ll hear the siren chirp to indicate
the current status. Then, the system allows you to enter another selection like
return to step d.
g. Once finish the programming, turn ignition ON and press switch one time.
The system will exit the programming mode.
Example:
To turn Arm/Disarm with chirp OFF under ON status, press switch 6 times
after step a-d. Every press will have every chirp. You need to finish the
procedure within 20 sec. Then, turn ignition ON, you’ll hear two chirps
which indicates the status is OFF now. Then, the system should allow you to
enter another function programming.
PRE SET VALUE
(1 CHIRP)
VARIABLE SET-UP
(2 CHIRPS)
1. LOCK/UNLOCK TIMER 0.5 SEC 3.5 SEC
2.UNLOCK PULSE 1 2
3.SECOND UNLOCK BOTH SECOND UNLOCK
4. IGNITION ON WITH DOOR LOCK ON OFF
5.SILENT ARM WITH SHOCSENSOR ON OFF
6. ARM/DISARM WITH CHIRP ON OFF
7. ANTI-CARJACKING ON OFF
8. LAST DOOR ARMING ON OFF
9.LASTDOOR ARMING WITH LOCK OFF ON
10. AUTO RE-ARM ON OFF
11. AUTO RE-ARM WITH LOCK OFF ON
12. VALET ON OFF
15. SOUND CONTINUOUS SOUNDING SOUND 1S THEN BREAK 1S
16.LAST DOOR ARMING ACC/FULL FULL ACC
25. DEFAULT YES
1. Lock/Unlock Timer
Pre-set: After press arm/disarm, the door is locked/unlocked after 0.5 sec.
Variable: After press arm/disarm, the door is locked/unlocked after 3.5 sec.
2. Unlock pulse
Pre-set: 1 pulse
Variable: 2 pulses
3. Second unlock
Pre-set: unlock at same time.
Variable: second unlock
4. Ignition ON with door lock
Pre-set: When the ignition is turned from OFF to ON, doors will be locked
after 20 sec.
Variable: When the ignition is turned from OFF to ON, door will be not
locked.
5. Silent arm with Shock Sensor
Pre-set: When in silent arming, shock sensor will work normally.
Variable: When in silent arming, shock sensor will not work.
6. Arm/Disarm with Chirp
Pre-set: Arm/Disarm will have chirp indication.
Variable: Arm/Disarm will not have chirp indication.
7. Anti Car-hijacking
Pre-set: Follow procedures to enter anti car-hijacking mode.
Variable: Delete anti car-hijacking feature.
8. Last Door arming
Pre-set: Turn ignition OFF and close the last door. After 30sec, the system
will arm itself.
Variable: Delete this feature.
9. Last Door arming with Door Lock
Pre-set: Delete this feature.
Variable: this feature exists.
PS. This feature has to be selected under the Last door arming function is
selected ON.
10. Auto Re-arm
Pre-set: this feature exists.
Variable: Delete this feature.
11. Auto Re-arm with lock
Pre-set: Delete this feature
Variable: this feature exists.
PS. This feature has to be selected under the Auto Re-arm function is selected ON.
12. Valet
Pre-set: follow the procedure to enter Valet mode.
Variable: delete this feature.
15. Sound
Pre-set: In emergency, siren continues sounding (if connected)
Variable: The output is to sound for 1 sec, then break for 1 sec. Repeat the
cycle for 30 secs.
16. Last Door Arming ACC/FULL
Pre-set: Last door arming with all sensors could activate alarm.
Variable: Last door arming with only ignition activate alarm.
25. Default
Pre-set: Return to the factory set-up.
Notice :
The changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
REV: A
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.