Product Manual

ManualsBrandsPorto-Power ManualsAuto Body Repair10-Ton Pulling Post Package

Items included:

B93600A • 10 Ton Pulling Post

B65428 • Air Pump with Hose

B65444 • 10 Ton 10" Stroke Ram

B97662 • Chain & Craw Hooks (2pc.)

B97691 • Chain & Grab Hook

Pulling Post Kit

Operating Instructions & Parts Manual

- Before using this product, read this manual and follow all its Safety Rules and Operating Instructions

10939 N. Pomona Ave. Kansas City, MO 64153

816-891-6390

sales@blackhawk-automotive.com

Made in USA

Porto-Power Blackhawk Automotive is a licensed trademark

Model Number B93601A

Summary of content (8 pages)

PAGE 1
Porto-Power Blackhawk Automotive is a licensed trademark Pulling Post Kit Operating Instructions & Parts Manual Model Number B93601A Items included: B93600A • 10 Ton Pulling Post B65428 • Air Pump with Hose B65444 • 10 Ton 10" Stroke Ram B97662 • Chain & Craw Hooks (2pc.) B97691 • Chain & Grab Hook SFA Companies ©2005 10939 N. Pomona Ave. Kansas City, MO 64153 816-891-6390 sales@blackhawk-automotive.
PAGE 2
TIME LIMITED WARRANTY For the periods of time indicated below, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remedy.
PAGE 3
SAVE THESE INSTRUCTIONS For your safety, read and understand the information contained within. The owner and operator shall have an understanding of this product and safe operating procedures before attempting to use this product. Instructions and Safety information shall be conveyed in the operators native language before use of this product is authorized. Make certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of the product.
PAGE 4
Hanger Floating Pulley Safety Chain 9' Pull Chain with Grab Hook, 3/8" 6' Chain with 2 Claw Hooks, 3/8" Support Bar Secondary Safety Tie Idle Pulley Recycling Lock Power Lever Arm Porto-P ower BLACKHA WK AUT OMOTIVE Wheel Hydraulic Hose 10 Ton Threaded Ram Air Hydraulic Pump Oil Outlet Port, 3/8" Air Inlet Port, 1/4" Figure 1 - B93601A Components SAFETY INSTRUCTIONS BEFORE USE 1. Study, understand, and follow all instructions provided with and on this device before use. 2.
PAGE 5
! WARNING! ! WARNING • All WARNING statements must be carefully observed to help prevent personal injury. • Do not exceed rated capacity. • All devise used must be rated for the same maximum operating pressure, correctly connected and compatible with the hydraulic fluid used. An improperly matched system can cause the system to fail and possibly cause serious injury. • Use only on hard, level surfaces capable of sustaining rated capacity loads.
PAGE 6
SET UP (refer to figure 1 on page 4) Safety Mesage! It is recommended that you install a pressure gauge on your pump to indicate a relative level of pulling force. 1. Secure the threaded ram to bottom of puller post, then connect ram to air pump with hydraulic hose provided. 2. Slide the 9 feet pull chain thru the floating pully, idle pulley and power lever arm. 3.
PAGE 7
MAINTENANCE 1. Inpect and replace damaged, kinked, twisted, stretched or rusty chain. 2. Inspect hoses and connections. Replace damage components immediately with Porto-Power Blackhawk replacement parts only. 3. Tighten connections as needed. Use non-hardening pipe thread compound when servicing connections. 4. Use only good quality hydraulic fluid. We recommend Hein-Werner HW93291 or equivalent.
PAGE 8
REPLACEMENT PARTS Please refer to the Parts drawing when ordering parts. Not all components are replacement items, but are illustrated as a convenient reference of location and position in the assembly sequence. When ordering parts, give model no., serial no. and description below. Call or write for current pricing: SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A. Tel:(816)891-6390 Fax:(816)891-6599 E-Mail: sales@blackhawk-automotive.