Printer User Manual

ManualsBrandsPOSIFLEX Business Machines ManualsPrinterpp-7000U-III

Part 1

Aura Series

(PP-7000-III / PP-7000U-III)

THERMAL PRINTER

TECHNICAL INFORMATION

A. INTERFACES

1. Peripheral interface

The connector for peripheral control is a 6P6C RJ11 jack with

the following pin assignment. The best recommended cash drawers to

this connector are Posiflex CR3100, CR3200, CR4000 and CR4100.

Using the cable 20863018001 (CCBLA-180-1) delivered with the

cash drawer, the Aura series can control one dedicated cash drawer.

However, by using an optional split cable 20867023800 (CCBLA-

238), Aura series controls two cash drawers through this connector.

Please connect the CR1 plug to the cash drawer (CRA) to be opened

by command Esc p 1 n1 n2 and the CR2 plug to the cash drawer

(CRB) to be opened by command Esc p 0 n1 n2

6P6C RJ11 jack

6 pin plug

Summary of content (7 pages)

PAGE 1
Aura Series (PP-7000-III / PP-7000U-III) THERMAL PRINTER TECHNICAL INFORMATION A. 1. INTERFACES Peripheral interface The connector for peripheral control is a 6P6C RJ11 jack with the following pin assignment. The best recommended cash drawers to this connector are Posiflex CR3100, CR3200, CR4000 and CR4100. Using the cable 20863018001 (CCBLA-180-1) delivered with the cash drawer, the Aura series can control one dedicated cash drawer.
PAGE 2
PIN # Definition Description 1 FG Frame ground Drawer kick for cash drawer controlled by 2 CRB software command Esc p 0 n1 n2 3 SENSE Input peripheral status 4 VCC + 24 V DC supply Drawer kick for cash drawer controlled by 5 CRA software command Esc p 1 n1 n2 6 SG Signal ground B. SETUP WINDOW On bottom cover of the Aura series thermal printer, there is screwed a metal plate for setup window. In this window, there is a 8 position DIP switch for printer setup.
PAGE 3
Effect of posit ions 1 & 2 on baud rate is defined as in table below with parity check set according to position 3, number of data bits always set to 8, and stop bit set to 1. When the parallel interface is used, please set both positions to ON. ON OFF ON OFF SW Pos. 1 SW Pos. 2 ON ON OFF OFF Baud rate 38400 bps / 4800 bps 9600 bps 19200 bps or Interface (Parallel) Switch position 3 defines the parity check regulation in serial interface. In Aura, it is selectable between even and none.
PAGE 4
Switch Position 1 2 3 4 5 6 7 8 Serial interface OFF OFF OFF OFF OFF OFF OFF OFF w/ auto cutter Parallel interface ON ON OFF OFF OFF OFF OFF OFF w/ auto cutter C. INTERNAL SWITCH There is an extra internal 4 position DIP switch in PP-7000-III series for more technical settings. To access these setup, please first turn off the printer power and disconnect every cable from the printer. Remove 4 screws from bottom of printer and remove the plastic bottom cover with the power switch pressed.
PAGE 5
description of the supported commands if required. 1. Paper out alarm When Paper End signal is detected, the printer keeps on intensive beeping and stops receiving data till the signal is neutralized. When Paper Near End signal is detected, the printer gives a beep every 3 seconds and stops receiving data. 2. Enhancement commands Following commands are included in the printer firmware version since ver. 3.
PAGE 6
bell onto say a kitchen wall, connect the cable from the bell to the peripheral connector on the printer. Then use this command with m set to 0 and both n1 and n2 set to 255. The printer will be able to drive the kitchen bell for about half a second on each such command. If this command is sent to the printer multiple times consecutively, the bell will ring for about half a second and rest for also about half a second then ring again for multiple times.
PAGE 7
Page 19 (PC858: Euro Dollar Sign included in PC850 for European / Greek model) Page 253 (Greek437 as Default setting for Greek model) Page 255 (Thai for Standard model) Page 255 (Greek for European / Greek model) Page 255 (PC864: Arabic as Default setting for Arabic model) Page 255 (Lithuanian as Default setting for Lithuanian Model) Further support to some double byte language systems can be achieved by adding each relevant font chip in standard model: Japanese: Kanji Korean: KCS5601 Traditional Chinese: B