PP2000 Series 2 Station Printer User’s Guide Rev.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents PRODUCT BRIEFING . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 MAIN PARTS ON THE EXTERIOR . . . . . . 2 -- 1 OUTPUT AREAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -- 1 CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -- 1 INPUT / OUTPUT CONNECTOR . . . . . . . . . . . . . . . . 2 -- 2 INSTALLATION -------------- MAINTENANCE NOTICES . . . . . . . . . . . . . . . . 4 -- 1 SOFEWARE COMMANDS . . . . . . . . . . . . . . . . .
STORE STAMP (OPTION) . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 INTERNAL SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 CASH DRAWER CONNECTOR . . . . . . . . . . . . . . . . . 6 -- 5 SERIAL INPUT CONNECTOR (STANDARD 9 PIN RS232 INTERFACE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 -- 5 POWER INPUT CONNECTOR . . . . . . . . . . . . . . . . . . 6 -- 5 PARALLEL INPUT CONNECTOR (STANDARD 25 PIN SPP INTERFACE) . . . . . . . . . . . . . . . . . . . . . . . . . . .
I. PRODUCT BRIEFING This is a high speed 2 - station journal / receipt printer. l A standard 2 station Journal / Receipt printer: The printing paper width is 44.5mm. The printer can print both journal and receipt at the same time or only journal or receipt alone. l The ability for validation printing. l The configuration of print head is a 9 Pin impact print head. The maximum printing speed is about 3 lines / sec and 24 characters / line.
l Options include auto stamping ability of the store stamp on receipt and auto cutting of the receipt. l The ability of cutting paper in full or in part by software on receipt.
II. MAIN PARTS ON THE EXTERIOR A. OUTPUT AREAS Receipt exit slot Journal window Validation printing insert slot B.
C.
III. INSTALLATION A. CHECK CONTENTS When you unpack carefully the carton that delivers PP2000 series printer, you will find it contains several items as illustrated below. l l l l PP2000 2 - station receipt / journal printer Two rolls of paper roll sample One set of ribbon Power adaptor with power cord (option) If there is any discrepancy or problem, contact your dealer immediately. Be sure to save the packing materials in the event that the printer may need to be shipped at some point in the future. B.
C. STORE STAMP INSTALLATION Print anvil assembly Print head assembly If your printer comes with stamp option, you can find a store stamp case in the rear of the receipt part of print anvil assembly. You may take it out gently by holding its handle with your fingers.
of store stamp. When the printing ink of the stamp is not enough, you can drip printing ink into the two holes in the rear of the stamp case. D. RIBBON INSTALLATION / REPLACEMENT Handle of the ribbon Location of the ribbon When replacing the ribbon, please take the handle at the center of the old ribbon case and lift it up. Then the old ribbon can be taken out.
turn the knob of the ribbon in the marked direction to tighten the ribbon and to ensure proper operation of the ribbon and to avoid jamming. E. CASH DRAWER CONNECTION Using the Posiflex signal cable CCBLA-180 to control a Posiflex cash drawer (CR3100 or CR3200). However, by using the Posiflex signal split cable CCBLA-238, PP2000 series can control two Posiflex cash drawers (CR3100 or CR3200). (CCBLA-180 is a standard accessory with the Posiflex cash drawer CR3100 or CR3200.) F.
H. POWER ON Turn on the On/Off switch at the left to the control panel, there will be a short buzzing sound and it indicates a normal power on. I. PAPER ROLLS INSTALLATION Direction of rolling Pick up reel of journal Journal lever Roll of journal Receipt lever Roll of receipt Insert slot of journal Insert slot of receipt 1. Please refer to the picture above: Put the receipt roll into the left paper roll compartment and the journal roll into the right.
4. To give an idea about the positioning matter of the receipt, the print center is 33.3 mm behind the auto-cut position, whilst the stamp center is 40.0 mm behind the print center. J. SELF TEST Please power off the printer for at least three seconds and then press and hold the receipt button while turning the on / off switch on. A slip of self test result is printed on both receipt and journal side. Any signal of the receipt button after the printing of self test result will cause paper feed of receipt.
IV. MAINTENANCE NOTICES l l l l ² The printer should be put at a well ventilated site and avoid direct sunshine, also avoid high temperature, high humidity, high magnetic field. The site should also be free from lots of metal chips and dust. Never place any vessel for water alcohol beverages or any kind of fluid over the printer. Otherwise it may get turned over and damage the component inside.
V. SOFTWARE COMMANDS The commands supported by the PP2000 Printer are listed below. For detail description of the below listed commands, please visit our web site http://www.posiflex.com.tw for detail descriptions of each command.
Software commands continued.
VI. SPECIFICATIONS A. VALIDATION PRINTING 10 84.5 Print area Sensor Unit: mm Note: Do not scale 8 22 2 Paper width: 140 mm or above Paper height: 65 mm or above Paper thickness: 0.07 ~ 0.14 mm Validation print: One line Number of characters: 55 Print area and sensor position: As illustrated in drawing above B. PAPER ROLL Paper type: High quality paper Paper roll width: 44.5 +/- 0.5 mm Paper roll max. O. D.: 83 mm Paper thickness: 0.06 ~ 0.
C. LED INDICATIONS Power LED: Green: Printer power is working On line LED: Green: Printer is at on line state. The printer takes command from the host system at this state and takes no command from the buttons. Receipt LED: Red: Receipt paper is out, or malfunction with receipt print. Journal LED: Red: Journal paper is out or malfunction with journal print. D. BUTTON FUNCTIONS On line button: Switches the printer between on line and off line states. The data in the buffer keep printing out.
E. PRINTER GENERAL SPEC ITEM Functions Printing Method Printing Speed Printing Capacity Paper Feed Max. Paper Feed Speed Built in Characters Data Buffer Paper Type Inked Ribbon Receipt Pattern Auto Interface Sensor Control over Cash Drawers Power Used 6-3 SPECIFICATION Receipt, journal and validation printing 9pin dot matrix impact; synchronized or separate printing of receipt and/or journal About 3 lines/sec.
F. STORE STAMP (OPTION) Cushion width: 34.0 mm Cushion height: 24.0 mm Cushion thickness: 1.0 mm Cushion material: PE foam Stamp total width: 34.0 mm Stamp total height: 24.0 mm (engraving included) Stamp total thickness: 5.0 mm Engraving width: 30.0 mm Engraving height: 20.0 mm Engraving thickness: 1.2 mm Stamp material: porous rubber Ink type: pre-inked stamp ink (has to match the material of stamp) G.
H. CASH DRAWER CONNECTOR PIN 1 2 3 4 5 6 DEFINITION Frame ground CR2 kick (by Esc p 0 n1 n2) Drawer open sense +24V DC power CR1 kick (by Esc p 1 n1 n2) Signal ground I. SERIAL INPUT CONNECTOR (standard 9 pin RS232 interface) J. POWER INPUT CONNECTOR PIN 1 2 3 CASE DEFINITION +24 V DC power Power ground N. C. Frame ground 1 CASE 3 2 K. PARALLEL INPUT CONNECTOR (standard 25 pin SPP interface) L. DIMENSION AND WEIGHT Length Width Height Weight PRINTER 265 mm 176 mm 193 mm 2.5 Kg 3.
M. ENVIRONMENT Temperature: 0°C to 50°C Humidity: RH 10% to RH 90% without condensation N. RELIABILITY Printer mechanism (without print head) life: 8,000,000 lines Print head life: 150,000,000 characters (2 dots/wire/character average) O. POWER ADAPTOR PA-300 ITEM INPUT VOLTAGE RANGE INPUT FREQUENCY OUTPUT VOLTAGE OUTPUT POWER CONTINUOUS LOAD OUTPUT STABILITY RIPPLE AND NOISE ² SPECIFICATION 100 V AC to 250 V AC 50 to 60 Hz +24 V DC max. 60 W max. 2.2 A +/- 5% max.
VII. REGULAR MAINTENANCE PROCEDURE A. DAILY MAINTENANCE Perform a basic cleaning and maintenance daily at a suitable timing as following Paper exit area 1. Turn power off and open the top cover. Press down the receipt lever and the journal lever. Take out both the paper roll of receipt and journal. 2. Use the attached soft brush to clean the area of the paper exit as indicated in Fig.1. Fig 1 Paper exit area 3.
B. PERIODIC MAINTENANCE A periodic maintenance and lubrication should take place by a qualified maintenance specialist in every 6 months.
VIII. BASIC TROUBLE SHOOTING A. NO OPERATION AFTER POWER ON If the printer does not work, neither does the power on LED lit: 1. Check if the power cord is well connected. 2. Check if the power outlet the printer is connected to is supplied with power. 3. If the printer does not work, neither does the buzzer beep, however the power LED does lit, please contact the service dept. of the manufacturer. B. CAN NOT PRINT WITH A NORMAL POWER ON 1. Check if the on line LED is turned on. 2.
D. PAPER JAMMED Receipt lever Journal lever Raise the print anvil assembly In case of serious paper jammed problem, please pull both the receipt lever and the journal lever forward and push the print anvil assembly backward (as indicated in the picture) to raise the print anvil assembly.
Once the print anvil assembly is lifted, the paper jam can be dismissed. Please clean the paper residue in the area before putting back the print anvil assembly if the condition requires. Pick up reel moves back Original location When you are putting back the print anvil, please pay special attention to the position of the pick up reel for journal. Because the journal pick up reel moves backward automatically when the print anvil is raised.
No auto-return with print anvil However, the journal pick up reel does not automatically move forward when the print anvil assembly is put back. Direction to roll Please then put the journal pick up reel back to its original location, and roll the reel so that the journal remains properly tensioned.
