A10 USER MANUAL
EN P03 FR P26 ES P49
WHAT’S IN THE BOX FLORIO A10 ROBOTIC MOP DOCKING STATION A10 A10 USER MANUAL POWER CORD CLEANING SOLUTION DISPOSABLE CLEANING PAD RUBBER CLEANING PAD BASE USER MANUAL QUICK START GUIDE QUICK START GUIDE CLEANING TOOL *The illustrations in this manual are for reference only. The actual appearance may vary.
SYMBOLS CONTENTS For indoor use only WHAT’S IN THE BOX P03 To reduce the risk of injury, user must read instruction manual PRODUCT SAFETY P05 Caution TECHNICAL SPECIFICATIONS P09 ABOUT YOUR FLORIO A10 ROBOTIC MOP P10 ABOUT YOUR DOCKING STATION
PRODUCT SAFETY 3. WARNING: This product can expose you to chemicals including lead and Di(2-ethylhexyl)phthalate (DEHP) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. 4.
FOR ALL BATTERY – OPERATED APPLIANCES: SAFETY WARNINGS FOR BATTERY PACK INSIDE THE TOOL 1. a) b) c) 2. 3. 4. 5. 6. 7. 8. 9. 10. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents. Recharge only with the charger specified by the manufacturer .
r) s) Do not mix cells of different manufacture, capacity, size or type within a device. Keep the battery away from microwaves and high pressure. SAVE THESE INSTRUCTIONS SAFETY PRECAUTIONS WHEN USING THIS PRODUCT CAUTION: Remain alert and follow the procedure below: Please read this manual carefully before using the product and keep it properly. The robot is not a toy. Supervise children and pets when the robot is cleaning DO NOT place anything on top of the unit.
19. 20. 21. 22. 23. 24. 25. Do not allow hair, clothes, fingers, or any other parts of human body to be close to the opening and operating parts of the product. The product should not be used on wet or watery ground. The product should not mop any flammable materials such as gasoline or toner powder for printers and photocopiers. The product should not be used for cleaning areas with flammable materials.
TECHNICAL SPECIFICATIONS NA0001 (Docking Station) NR001L (Florio A10 Robotic Mop) Dimension 264 x 263 x 95mm (10.4 x 10.4 x 3.7in) Dimension 320 x 300 x 256mm (12.6 x 11.8 x 10.1in) Weight 3kg (6.6lbs) Weight 3.5kg (7.7lbs) Battery capacity Li Battery 2600mAh Adaptor model AD-0121900060US Rated voltage 14.4V Adaptor input 100-240V~50-60Hz 0.5A Rated power 8.4W Rated input 19V Rated output 19V Rated power 11.4W 0.
ABOUT YOUR FLORIO A10 ROBOTIC MOP TOP VIEW BOTTOM VIEW REMOVABLE WATER TANK HOME BUTTON LASER DISTANCE SENSOR (LDS) POWER BUTTON DRIVE WHEELS MAGNETIC CLEANING PAD BRACKET WATER OUTLET BUMPER BUMPER CHARGING SENSOR CARPET DETECTION SENSOR CASTER WHEEL 10 EN
ABOUT YOUR DOCKING STATION FRONT VIEW BACK VIEW CHILD LOCK CLEANING MODE SELECTION NEW CLEANING PAD STORAGE START USED CLEANING PAD STORAGE POWER CORD HANDLE COVER CLEANING PAD CHANGING AREA EN 11
GETTING TO KNOW YOUR FLORIO A10 OPERATION PANEL FOR FLORIO ROBOTIC MOP OPERATION PANEL FOR DOCKING STATION CHILD LOCK POWER BUTTON Button / Indicator Operation and function Short press: the robot starts/pauses . Long press for 3 seconds: turn on/off the robot. Short press: Pause when the robot is cleaning. Short press again: Send the robot home to recharge. Long press for 3 seconds: Robot will start to spot clean.
TIPS BEFORE CLEANING Organize the space to be cleaned Open doors for an accurate floorplan map Create Virtual Boundaries In order to create the most accurate map of your home, ensure the robot has access to all the areas you would like it to clean. Open doors and remove any barriers to allow the robot to explore and map freely.
GETTING STARTED Remove all protective packaging materials Place the docking station Docking station location 1.5 m (5 ’) 0 (2.3.7m ’) Remove all protective foam and labels from the robot. 14 Remove the cover on the back of the docking station to plug in the AC adapter to the docking station and a wall outlet. 0 (2.3.7m ’) For best performance, place the docking station against a wall leaving at least 2.3 ft (70cm) on each side and at least 5ft (150cm) in front.
GETTING STARTED Assemble the cleaning pads Install the cleaning pad Insert the cleaning pads Wrap a new cleaning pad around the rubber mop pad base, folding the pad firmly around the sides of the base. Gently flip the robot over and align an assembled cleaning pad onto the magnetic mop bracket. Press firmly to ensure correct installation. Open the lid of the docking station and place the remaining assembled cleaning pads in the clean pad storage box.
GETTING STARTED Power on the Florio A10 DOWNLOAD THE APP Charging For best experience, download the NOESIS app to customize your cleaning, set a schedule and access even more features. Scan the QR code below or visit your mobile application store to download the "NOESIS HOME" app Long press “ ” for 3 seconds to turn on the robot. You will hear startup music to indicate success. Manually push the robot into the docking station to charge.
MAPPING YOUR HOME First Use: Creating the map Tips while mapping After the robot is fully charged, short press " " on the docking station. The robot will leave the docking station and begin exploring your home and building a map of your floor plan. Do not follow or stand in the way of the robot as it is mapping. This can cause missing spots or errors in your floor plan map. Note: The robot is NOT cleaning while building the map. The cleaning pad will be lifted up as it explores your home.
START CLEANING Start Cleaning Pause Return to the Docking Station 2 1 After the robot has mapped your floor plan, it is ready to clean! After recharging from its mapping journey, select the cleaning mode " and press " " on top of " the docking station or through the NOESIS HOME app. The robot will begin cleaning around the perimeter of the room before settling into a methodical back and forth pattern.
START CLEANING Your Florio A10 has 3 cleaning mode options: dry mopping, wet mopping or dry + wet mopping. The mode can be selected on top of the docking station or through the NOESIS HOME app. Note: Dry + Wet Mopping mode: the robot will dry mop first, when finished, it will go back and wet mop. If the battery depletes before the job is completed, the robot will return to the docking station to charge and will resume cleaning where it left off when it is fully charged. 1.
START CLEANING The Auto Change Pad Empty the Used Cleaning Pads Frequently By default, the robot will automatically change the cleaning pad after cleaning (20 m2). Customize when the pad is changed in the NOESIS HOME app by sq. ft. cleaned OR by room. Remember to dispose of the dirty cleaning pads that are collected in the used container. Lift the lid of the docking station to access the used pad container. Use the handles to lift the dirty cleaning pads out of the docking station.
MAINTENANCE Clean the water tank Remove the water tank by pressing the release key Empty the water tank Flush the water tank Dry the rubber base completely before assembling clean pads Dispose of the dirty disposable cleaning pads ONLY. Do not throw away the rubber base. Wipe dry or air dry Clean the rubber cleaning pad base It is recommended that you rinse the rubber base after disposing of the dirty pad.
MAINTENANCE: ROBOTIC MOP Use a dry, clean cloth to wipe all sensors and parts to keep the robot running at peak performance.
MAINTENANCE: DOCKING STATION Use a dry, clean cloth to clean the docking station. (NOTE: Use a dry cloth only. Do not use water to clean the docking station.
TROUBLESHOOTING Error Possible Cause Solution Mobile phone OS version is out of date Update your mobile phone under settings to the latest OS The robot is not in pairing mode Ensure the robot is on and then press “ ” and “ for 3 seconds until you hear voice confirmation Cannot connect to Wi-Fi network Select your 2.4 GHz network only. The robot cannot connect to 5G Failure to Update Firmware Interrupted network connection or improper update 1.
TROUBLESHOOTING Error Possible Cause Solution Water Tank Error The water tank is not installed properly Please check the water tank to ensure that it is installed properly Insufficient Water. Please Add Water The water level is too low in the water tank Please refill the water tank and reinstall it into the robot Drive Wheel Error One or multiple drive wheels is stuck or dirty Inspect the drive wheels for any foreign objects and wipe clean with a dry cloth Charging Error 1.
CONTENU DE LA BOÎTE FLORIO A10 SERPILLIÈRE ROBOTIQUE BASE À TAMPON NETTOYANT EN CAOUTCHOUC STATION D’ACCUEIL A10 A10 USER MANUAL CORDE D’ALIMENTATION SOLUTION DE NETTOYAGE MODE D’EMPLOI TAMPON NETTOYANT JETTABLE QUICK START GUIDE GUIDE DE DÉMARRAGE RAPIDE OUTIL DE NETTOYAGE *Les illustrations dans ce mode d’emploi sont à titre de référence seulement.
SYMBOLE Utilisation en intérieur uniquement Pour réduire le risque de blessure, l’utilisateur doit lire le mode d’emploi. Attention CONTENU CONTENU DE LA BOÎTE .................................................................................................P26 SÉCURITÉ DU PRODUIT..................................................................................................P28 SPÉCIFICATIONS TECHNIQUES...................................................................................P32 .
1. SÉCURITÉ DU PRODUIT AVERTISSEMENT : Ce produit peut vous exposer à des produits chimiques incluant le plomb et le Di(2-éthylhexyle)phtalate (DEHP) connus dans l’État de la Californie pour causer le cancer et des anomalies congénitales ou autres dommages à l’appareil reproducteur. Pour de plus amples renseignements, consultez www. P65Warnings.ca.gov.
14. Éteindre tous les contrôles avant de débrancher. 15. Ne pas utiliser sur des liquides inflammables et combustibles, comme l’essence, ni dans des zones où ces liquides peuvent être présents. 16. Pour réduire le risque d’incendie, ne pas utiliser un liquide inflammable ou combustible pour nettoyer le plancher. 17. Ne débranchez pas en tirant sur le cordon. Pour débrancher, saisissez le chargeur et non le cordon. POUR TOUT APPAREIL À BATTERIE : 1. 2. 3. 4. 5. 6.
avec beaucoup d’eau et consultez un médecin. N’utilisez pas un bloc-pile qui n’est pas conçu à être utilisé avec l’équipement. g) Gardez le bloc-piles hors de la portée des enfants. h) Achetez toujours le bloc-piles recommandé par le fabricant de l’appareil pour l’équipement. i) Gardez le bloc-piles propre et sec. j) Essuyez les bornes des recharges avec un linge sec et propre s’ils sont sales. k) Le bloc de batterie doit être chargé avant l’utilisation.
12. 13. 14. 15. Cet appareil n’est pas destiné à être utilisé par des personnes (y compris des enfants) ayant des capacités physiques, sensorielles ou mentales réduites, ou manquant d’expérience et de connaissances, sauf si une personne responsable de leur sécurité les supervise ou leur donne des instructions concernant l’utilisation de l’appareil. Utilisez le produit seulement dans un environnement domicile intérieur.
SPÉCIFICATIONS TECHNIQUES NA0001 (Station d’accueil) NR001L (Serpillère robotique Florio A10) Dimensions 264 x 263 x 95 mm (10,4 x 10,4 x 3,7 po) Dimensions 320 x 300 x 256 mm (12,6 x 11,8 x 10,1 po) Poids 3kg (6.6lbs) Poids 3.5kg (7.7lbs) Capacité de la batterie Batterie Li 2600mAh Modèle d'adaptateur AD-0121900060US Tension nominale 14.4V Entrée adaptateur 100-240V~50-60Hz 0.5A Puissance nominale 8.4W Entrée nominale 19V Sortie nominale 19V Puissance nominale 11.4W 0.
À PROPOS DE VOTRE SERPILLÈRE ROBOTIQUE FLORIO A10 VUE DU HAUT VUE DU BAS RÉSERVOIR D’EAU AMOVIBLE BOUTON D’ACCUEIL DÉTECTEUR DE DISTANCE LASER (LDS) BOUTON D’ALIMENTATION ROUES MOTRICES NETTOYAGE À ÉMANT SUPPORT À TAMPON SORTIE D’EAU AMORTISSEUR BUMPER CAPTEUR DE CHARGE DÉTECTEUR DE TAPIS ROUE PIVOTANTE FR 33
À PROPOS DE VOTRE STATION D’ACCUEIL VUE DE L’AVANT VUE DE L’ARRIÈRE VERROU POUR ENFANT NOUVEAU RANGEMENT POUR TAMPON DE NETTOYAGE RANGEMENT POUR TAMPON DE NETTOYAGE SÉLECTION DU MODE DÉMARRER DE NETTOYAGE CORDON D’ALIMENTATION POIGNÉE HOUSSE ZONE DE CHANGEMENT DE TAMPON DE NETTOYAGE 34 FR
DÉCOUVRIR VOTRE FLORIO A10 PANNEAU DE COMMANDE POUR LA SERPILLÈRE ROBOTIQUE FLORIO BOUTON D’ALIMENTATION BOUTON D’ACCUEIL Bouton / Indicateur + FR Opération et fonctionnement Brève pression : le robot démarre/pause. Longue pression pendant 3 secondes : éteindre/allumer le robot Brève pression : Mettre le robot en pause pendant qu’il nettoie. Brève pression de nouveau : Envoyer le robot à l’accueil pour recharger. Longue pression pendant 3 secondes : Le robot commencera à nettoyer l’endroit désigné.
CONSEILS AVANT DE NETTOYER Organiser l’espace à être nettoyé Ouvrez les portes pour une carte exacte de votre maison Afin de créer la carte la plus exacte de votre maison, assurez-vous que le robot puisse accéder à toutes les zones que vous voulez nettoyer. Ouvrez les portes et enlevez toute barrière pour permettre au robot d’explorer et tracer le plan sans obstructions.
COMMENCER Enlevez tous les matériaux d’emballage de protection Placer la station d’accueil Emplacement de la station d’accueil 1.5 m (5 ’) 0 (2.3.7m ’) Enlevez toute la mousse protectrice et les étiquettes du robot. FR Enlevez la housse de l’arrière de la station d’accueil pour brancher l’adaptateur AC à la station d’accueil et à la prise au mur 0 (2.3.
