Owner's Manual

MKT. #8830023 - REV B
11/13
PRINTED IN USA PAGE 1 OF 4
PFC-6075R
FIRE ALARM & RELEASING CONTROL PANEL
Potter Electric Signal Company, LLC • St. Louis, MO • Cust Service: 866-956-1211 • Tech Support: 866-240-1870 • Canada: 888-882-1833 • www.pottersignal.com
The PFC-6075R is a versatile seventy-ve (75) point analog/addressable releasing re alarm control panel that utilizes the Potter/
Nohmi device protocol that has a complete line of initiating and control devices. The SLC is capable of 50 ohms of resistance and
does not require the use of twisted or shielded wire. The signaling line circuit may be any combination of smoke sensors, heat de-
tectors or modules. The PFC-6075R will operate with a small Pre-Action water based system or a complex multiple criteria agent
suppression system.
The panel is specically designed for releasing service with software zones for cross zoning, counting zones, timers and system
release abort features. The display includes Pre-Discharge and Discharge LEDs to assist in providing system and releasing status.
The releasing and additional releasing notication circuits may be expanded using the PSN-1000 intelligent power supply.
The complete system may be converted to Class A with a CA-6075 module. The CA-6075 provides the hardware necessary to
convert the remote annunciators through the Potter P-Link connection protocol, the NACs and the SLC to Class A operation.
The panel has auto-programming learn mode that will not affect the existing system when adding or deleting a device. The system
is capable of 99 software zones, cross zoning and counting zones. The panel is fully programmed from a PC based software pro-
gram that will work with Microsoft XP, Vista or Windows 7.0 operating systems.
The PFC-6075 has an Ethernet connection for programming network connectivity and IP reporting communicator. The system has
a built in e-mail function and will send system E-mail reminders based on user dened dates. The IP communicator is listed with
the Sur-Gard III IP receiver.
The panel will support P-Link devices which include: the RA-6075R, RA-6500R and LED-16 Annunciators, RLY 5 Relay
Module, SPG-1000 Serial Parallel Gateway (printer card), FCB-1000 Remote Ethernet/IP connection, DRV-50 LED driver for 50
LEDs, PSN-1000 Remote Power Supplies (10 Amp) and FIB-1000 P-Link Fiber Interface Module. In addition, the panel allows
for the installation of the UD-1000 dual line telephone line digital alarm communicator transmitter (DACT). The UD-1000 is
programmable for a single line or dual line and is compatible with Ademco’s Contact ID or SIA DCS protocols.
Features
• 75 Analog/Addressable Points in Any Combination
• 99 Software Zones
• NFPA 72 Compliant Smoke Sensitivity Test Built-In
• System Operates as Class A or Class B for SLC, P-Link and
NACs
• 5 Amp Power Supply
• 2 NACS, Regulated, Rated at 3 Amps each listed for releasing
• 2 Input/Output (I/O) Circuits for system exibility rated at 1 Amp
each, ideal for manual release and abort
• Strobe Synchronization and System Wide Sync for Potter/
AMSECO®, Gentex®, Cooper Wheelock® and System Sensor®
strobes
• Dedicated Alarm, Supervisory and Trouble Relays
• 1,000 Event History Buffer
• Metal Dead Front Cabinet for Clean Look
• Cabinet will house up to 18 AH batteries
• Optional two line DACT with UD-1000 that can report General,
Zone or Point
• P-Link Communication Line for Annunciators and Accessories
• Ethernet Port for Programming and Network Connectivity
• E-Mail System Status, Reports and Event Information
• Size (W x H x D): 16" x 17" x 3 7/8"
Product includes a 5 year warranty
S735 7165-0328:0195
NYC Fire Dept.
Certicate of Approval
6157
firealarmresources.com