Assembly Instruction

ManualsBrandsPottery Barn ManualsOther RoomsPottery Barn Armoire Changing Table

pottery barn kids

ARMOIRE CHANGING TABLE

WARNING:

FALL HAZARD

To prevent death or serious injury from

falls, always keep child within arm’s reach.



Read all instructions before use of the changing table. K

EEP

INSTRUCTIONS FOR FUTURE

USE



fore each use check the changing table for damage, loose parts, or sharp edges. D

NOT

use the changing table if it is damaged or broken.



Set up this table to be level, stable, and structurally sound.



This changing table may be used with or without a pad.

The only pad approved for use with it

is the Contour Changing Pad available for purchase from pottery barn kids.

This pad is

designed to be used in a space of at least 810 mm x 400 mm (32 inches x 16 inches).

If used,

place it within the

rail

bound

ed c

hanging area

of the changing

table



NEVER LEAVE THE CHILD UNATTENDED and always use the restraining system.

This changing table is intended for us

e with children weighing up to

pounds.

PRE

ASSEMBLY:



Please read all instruction before beginning assembl

The illustrations provided allow for easier assembly

when used in conjunction with the assembly instructions.



Remove all parts and hardware from box and lay out on a carpeted or scratch

free work

surface,

as t

his will

avoid damaging any parts during ass

embly. The shipping box provides and ideal work surface

Do not dispose

of any contents until assembly is completed to avoid accidentally discarding small parts or hardware.



For your safety and

ease, adult assembly

by t

wo people is recommended.



Save all p

acking materials until assembly is complete to avoid accidentally discarding smaller parts or

hardware.



Use the parts and hardware lists to identify and separate each of the pieces included prior to starting

assembly.



Note: Do not fully tighten all bolts

until all parts are in place. Failure to follow these instructions may cause the

bolts to misalign during assembly.



If using power tools to aid in assembly please use caution. Power tools can damage hardware or split wood.

Summary of content (10 pages)

PAGE 1
pottery barn kids ARMOIRE CHANGING TABLE ! WARNING: FALL HAZARD - To prevent death or serious injury from falls, always keep child within arm’s reach.  Read all instructions before use of the changing table. KEEP INSTRUCTIONS FOR FUTURE USE.  Before each use check the changing table for damage, loose parts, or sharp edges. DO NOT use the changing table if it is damaged or broken.  Set up this table to be level, stable, and structurally sound.  This changing table may be used with or without a pad.
PAGE 2
PARTS INCLUDED: A (A) Top - 1pc D (B) Left panel - 1pc (C) Right panel - 1pc K (D) Front rail - 1pc C (E) Adjustable shelves - 2pcs E (F) Drawer Box - 1pc (G) Base - 1pc (H) Legs - 4pcs I B (I) Topper - 1pc (K) Back panel-upper - 1pc F TOOLS REQUIRED: Phillips head screwdriver (not included) HARDWARE ENCLOSED: (L) 1/4x32mm Bolts - 8pcs (M) 1/4x38mm Bolts - 8pcs (N) 1/4x64mm Bolts – 6pcs (O) Nuts – 6pcs (P) #3x20mm Screws– 30pcs (Q) Shelf supports – 8pcs (R) Curve washers – 2pcs (S) #5x20
PAGE 3
(U) Ø8x30mm Dowels – 8pcs ASSEMBLY INSTRUCTIONS: 1. Insert dowels (U) into left panel (B) and right panel (C) . (See Fig.1) (Fig. 1) C B U 2. Remove all drawers from the Drawer Box (F). (See Fig.2) (Fig.
PAGE 4
3. Lay the Drawer Box (F) down on the Left Panel (B). Align the pre-drilled holes of Drawer Box (F) to the pre-drilled holes of Left Panel (B) and fasten using Bolts (L). Tighten with Allen Key (Z).Insert Front Rail (D) into the pre-drilled holes of Left Panel (B) and fasten using Bolts (M) with Curve Washer (R). Tighten with Allen Key (Z). (See Fig.3 ) (Fig. 3) F M R D L B 4. Place the Right Panel (C) onto the Drawer Box (F).
PAGE 5
. Attach the Base (G) to the bottom of Drawer Box (F) and fasten using Bolts (M). Tighten with Allen Key (Z). (See Fig.5 ) (Fig. 5) M G 6. Attach the legs (H) to the Base (G).Fasten the wood blocks to the the Base (G) using Screws (X). Tighten with Phillips head screwdriver. (See Fig. 6 ) (Fig.
PAGE 6
7.Attach Top (A) to the panels and fasten using Bolts (N) with Nuts (O). Tighten with Allen Key (Z). (See Fig. 7 ) (Fig. 7) A O N 8.Turn the armoire upright. Align the pre-drilled holes of Top (A) to the pre-drilled holes of Front Rail (D) and fasten using Screws (X). Tighten with Phillips head screwdriver. (See Fig. 8 ) (Fig.
PAGE 7
9. Fasten Back Panel-Upper (K) to the assembled parts using Screws (P). Tighten with Phillips head screwdriver.(See Fig. 9 ) (Fig. 9) P K 10. Fasten Knobs (Y) to drawers using Screws (T). Tighten with Phillips head screwdriver. (See Fig.10 ) (Fig.
PAGE 8
11. Insert Shelf Supports (Q) into the pre-drilled holes of the side panels at the desired height. Place the Adjustable Shelves (E) onto the Shelf Supports (Q). Ensure the Adjustable Shelves (E) are properly supported by all Shelf Supports (Q).Note: Install only one shelf in the highest position while being used as a changing table. Store the second shelf for future use when converting to an Armoire. (See Fig.11) (Fig. 11) Q E Q E 12.Fasten the Scews(W) to the hole of Adjustable Shelves (E).
PAGE 9
13. Carefully place the Topper (I ) on Drawer Box ( F). (See Fig.13) (Fig. 13) I 14. Align the pre-drilled holes of the Topper ( I ) to the pre-drilled holes at the Back Panel-Upper (K) of the armoire and fasten using Screws (S).Tighten with Phillips head screwdriver. (See Fig.14) (Fig.
PAGE 10
15. If your floor is not perfectly even, the furniture may not sit level. Determine which corner does not touch the ground correctly With two people follow these steps: • Carefully elevate the item slightly to provide access to the levelers attached to the bottom. • Turn the levelers in a counter-clockwise direction. • Gently set down the piece and check stability. • Repeat steps until the furniture sits firmly on the ground. (See Fig.15) (Fig.