IMPORTANT MANUAL Do Not Throw Away OPERATOR'S MANUAL MODEL: WARNING: Read this Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. PB18VA46 LAWN TRACTOR ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulanpro.com Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 585 94 61-26 09.16.13 BD Printed in the U.S.A.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN • • WARNING. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. If fuel is spilled on clothing, change clothing immediately. Never overfill fuel tank. Replace gas cap and tighten securely.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 2.5 Gallons (9.46 L) Unleaded Regular Oil Type: (API: SG-SL) SAE 30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: w/Filter: w/o Filter: Spark Plug: Champion RC12YC Gap: .030"(0.76 mm) Charging System: 3 Amps Battery 5 Amps Headlights Battery: Amp/Hr: Min. CCA: Case Size: Blade Bolt Torque: 45-55 FT. LBS. (62-75 Nm) CONGRATULATIONS on your purchase of a new tractor.
UNASSEMBLED PARTS Slope Sheet Keys Oil Drain Extension (1) Quick Connect Key(s) ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY ✓CHECKLIST NOTE: You may now roll your tractor off the skid. Continue using the instructions that follow to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Ensure tractor is in a well-ventilated area. Ensure the area in front of tractor is clear of other people and objects.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. G H D E B F A J C K L M Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. ENGINE • Move throttle control (D) to slow position.
OPERATION TO USE CRUISE CONTROL (J) (See Fig. 7) TO ADJUST GAUGE WHEELS (See Fig. 9) The cruise control feature can be used for forward travel only. Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface.
OPERATION REVERSE OPERATION SYSTEM (ROS) (See Fig. 11) TO TRANSPORT (See Fig. 3 & 12) When pushing or towing your tractor, ensure transmission is disengaged by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control. • Pull freewheel control out until the free wheel control rod locks in extended position. • Do not push or tow tractor at more than two (2) mph (3,2 km/h).
OPERATION BEFORE STARTING THE ENGINE TO START ENGINE (See Fig. 3) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Ensure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position.
OPERATION MOWING TIPS • • • • • DO NOT use tire chains when the mower housing is attached to tractor. Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. The left hand side of mower should be used for trimming. Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (models with oil filter) E N G
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE V-BELTS TO CHANGE ENGINE OIL (See Fig. 16 & 17) Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • • • • TRANSAXLE MAINTENANCE The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle.
MAINTENANCE AIR FILTER CLEANING (See Fig. 19) Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. • • CLEAN AIR SCREEN The air screen is over the air intake blower located on top of engine. The air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. Clean engine, battery, seat, finish, etc. of all foreign matter.
MAINTENANCE DECK WASHOUT PORT (See Fig. 20) Your tractor’s deck is equipped with a washout port as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J). E A J F H B Fig. 24 Hook end of clutch cable spring (Q) into hole in idler arm (R).
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • Ensure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly. FRONT-TO-BACK ADJUSTMENT (See Figs. 29 & 30) IMPORTANT: Deck must be level side-to-side. Recheck measurements, adjust if necessary until both sides are equal.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 31) TO REPLACE MOTION DRIVE BELT (See Fig. 32) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL • Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).
SERVICE AND ADJUSTMENTS TO REMOVE WHEEL (See Fig. 33) TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully charged battery. • RED cable last from both batteries. • • Block up axle securely. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.
SERVICE AND ADJUSTMENTS ENGINE TO REPLACE HEADLIGHT BULB • • • • Raise hood. Pull bulb holder out of the hole in the backside of the grill. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. Close hood. TO ADJUST THROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION 8. Loose or damaged wiring. 9. Engine valves out of adjustment. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8. Check all wiring. 9. Contact an authorized service center/department. Hard to start 1. 2. 3. 4. 5. 6. 7. Dirty air filter.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
SERVICE NOTES 29
LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions. 1.
MANUAL IMPORTANTE MANUAL DE OPERARIO MODEL: NO TÍRALO A FUERA ADVERTENCIA: Leer, entender y seguir todas las instrucciones sobre la máquina y en el manual antes de empezar. Si no se observan las instrucciones de seguridad siguientes se pueden producir lesiones graves o la muerte. PB18VA46 TRACTOR PARA CÉSPED SIEMPRE USE PROTECCIONES PARA LOS OJOS MIENTRAS OPERE ESTE TRACTOR Vea la página web: www.poulanpro.com Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10).
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. • Nunca dejar una máquina encendida sin vigilancia.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles III. NIÑOS • • ADVERTENCIA: LOS NIÑOS PUEDEN SUFRIR DAÑOS CON EL USO DE ESTE EQUIPO. La Academia Estadounidense de Pediatría (American Academy of Pediatrics) recomienda que sólo se permita a niños con una edad mínima de 12 años manejar máquinas cortacésped manuales, y al menos de 16 años para manejar tractores cortacésped.
ESPECIFICACIONES DEL PRODUCTO Capacidad y Tipo de gasolina: 2.5 Galones (9.46 L) Regular Sin Plomo Tipo de Aceite: (API: SG-SL) SAE 30 (Sobre 32°F/0°C) SAE 5W30 (Debajo 32°F/0°C) Capacidad de Aceite: Con filtro: Sin filtro: Bujía: Champion RC12YC Abertura: .030"(0.76 mm) Sistema de Carga: 3 Amps Batería 5 Amps Luces Batería: Amp/Hr: Min. CCA: Case Size: FELICITACIONES por la compra de su tractor.
PEDAZOS PARA LA MONTAJE Llaves Extensión del aceite Accesorio del conexión Hoja de pendiente (2) Llaves MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. HERRAMIENTAS NECESARIAS PARA EL MONTAJE ETIQUETA Un juego de llaves de tubo facilitará el montaje. A continuación se enumeran los tamaños de las llaves estándar.
MONTAJE ✓LISTA DE REVISIÓN AVISO: Ahora puede sacar el tractor de la tarima. Continúe usando las instrucciones que siguen para retirar el tractor de la tarima. ADVERTENCIA: Antes de empezar, leer, entender y seguir todas las instrucciones presentes en la sección Operaciones de este manual. Asegurarse que el tractor esté en un área bien ventilada. Asegurarse que la zona delante del tractor esté libre de otras personas y objetos.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL DE OPERARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. G H D E B F A J C K L M Fig. 3 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas. COMO USAR SU TRACTOR MOTOR • Mueva el control de la aceleración (D) a la posición de lento.
OPERACIÓN UTILIZAR EL MANDO CRUCERO (Vea Fig. 7) • El césped promedio debe cortarse aproximadamente a 63,5 mm (2-1/2 pulgadas) durante la temporada fría y sobre 76,2 mm (3 pulgadas) durante los meses calurosos. Para obtener un césped más saludable y de mejor apariencia, siegue a menudo y después de un crecimiento moderado. • Para obtener el mejor rendimiento de corte, el césped que tiene más de 152,4 mm (6 pulgadas) de altura debe segarse dos veces.
OPERACIÓN PARA OPERAR EN CERROS PARA PARAR LAS CUCHILLAS DE LA SEGADORA • Desenganche el control del embrague del accesorio. ADVERTENCIA: No maneje hacia arriba o hacia abajo en cerros con pendientes superiores a 15° y no maneje atravesando ninguna pendiente. Utilice la guía de la pendiente proporcionada en la parte posteriora de este manual.
OPERACIÓN ANTES DE HACER ARRANCAR EL MOTOR PARA HACER ARRANCAR EL MOTOR (Vea Fig. 3) REVISE EL NIVEL DE ACEITE DEL MOTOR Al hacer arrancar el motor por la primera vez o si se ha acabado el combustible del motor, se necesitará tiempo para el arranque extra para mover el combustible desde el estanque hasta el motor. • Asegúrese que el control de rueda libre este en la posición enganchada. • Siéntase en el sillón en la posición de operación, suelte el pedal del freno y ponga el freno de estacionamiento.
OPERACIÓN CONSEJOS PARA SEGAR • • • • • NO use cadenas de llanta cuando la carcasa de la cortadora de césped esté colocada en el tractor. La segadora debe estar nivelada en forma adecuada para obtener el mejor rendimiento al segar. Vea “PARA NIVELAR LA CAJA DE LA SEGADORA” en la sección de Servicio y Ajustes de este manual. El lado izquierdo de la segadora se debe usar para recorte. Maneje de modo que los recortes se descarguen en el área que ya ha sido cortada.
MANTENIMENTO PROGRAMA DE MANTENIMIENTO ANTES DE CADA USO CADA 8 HORAS CADA 25 HORAS CADA 50 HORAS CADA 100 HORAS CADA ALMACENAMIENTO TEMPORADA Revisar la operación del freno Revisar la presión de las llantas Verificar la sistemas presencia del operador y sistemas "ROS" T R A C T 0 R Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel de bateria 4 Limpiar la batería y los tereminales Limpie los residuos de la placa de dirección.
MANTENIMENTO TRACTOR PRECAUCIÓN: Usar solamente la hojas de repuesto aprobada por el fabricante de su cortacésped. Usar una hoja no aprobada por el fabricante de su cortacésped es peligroso, puede dañar su cortacésped y anular su garantía. Siempre observe las reglas de seguridad cuando dé mantenimiento.
MANTENIMENTO PARA CAMBIAR EL ACEITE DEL MOTOR (Vea Fig. 16 y 17) CORREAS V Revise las correas V para verificar si existe deterioro y desgaste después de 100 horas de operación y cámbielas si es necesario. Las correas no son ajustables. Cambie las correas si empiezan a deslizarse debido al desgaste. Determine la gama de la temperatura esperada antes de cambiar el aceite. Todo el aceite debe cumplir con la clasificación de servicio API SG-SL. • Asegúrese que el tractor esté en una superficie nivelada.
MANTENIMENTO FILTRO DEL AIRE LIMPIEZA (Vea Fig. 19) Su motor puede sufrir averías y funcionar de manera incorrecta con un filtro del aire sucio. Déle servicio al filtro de aire más a menudo si se usa en condiciones polvorosas. Vea la manual de la motor. • • LIMPIEZA DE LA PANTALLA DE AIRE La pantalla de aire está sobre el soplador de la toma de aire que se ubica en la parte superior del motor.
MANTENIMENTO PUERTO DE LAVADO DE LA CUBIERTA (Vea Fig. 20) La plataforma del tractor está equipada con un puerto de lavado como parte del sistema de lavado de la plataforma. Se debe utilizar después de cada uso. 1. Lleve el tractor a un lugar horizontal y despejado de su césped, lo bastante cerca de una boca de riego como para que llegue la manguera del jardín. IMPORTANTE: Asegúrese de que la boca de descarga del tractor está orientada LEJOS de su casa, garaje, coches aparcados, etc.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal de freno completamente y aplique el freno de estacionamiento. • Ponga el embrague del accesorio en la posición "DESENGANCHADO". • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala. • Asegúrese que las cuchillas y que todas las partes movibles se hayan detenido completamente.
SERVICIO Y AJUSTES • • • FIJE LOS BRAZOS DE SUSPENSIÓN LATERALES DE LA CORTADORA (A) AL CHASIS - Ubique el orificio del brazo encima de la clavija (B) que hay en la parte exterior del chasis del tractor, y fíjelo con una resorte de contención. Realice el mismo procedimiento en el otro lado del tractor. Meta el fin de la conexión (E) en el hoyo en el suporte anterior de orificio y conecte con arandela e Retén del resorte (J). E J F A H Fig.
SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA AJUSTE DE DELANTE A ATRÁS (Vea Fig. 29 y 30) Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la segadora no está bien regulada. IMPORTANTE: El piso debe quedar bien nivelado de lado a lado.
SERVICIO Y AJUSTES PARA CAMBIAR LA CORREA DE LA CUCHILLA DE LA SEGADORA (Vea Fig. 31) PARA REEMPLAZAR LA CORREA DE TRANSMISIÓN (Vea Fig. 32) Estacione el tractor en una superficie nivelada. Ponga el freno de mano. Si necesita asistencia, del lado de abajo del apoyapiés hay una guía práctica para el montaje de la correa. DESMONTAJE DE LA CORREA 1. Desmonte la cortadora. (Ver “PARA DESMONTAR LA CORTADORA” en este capítulo del manual.
SERVICIO Y AJUSTES PARA HACER ARRANCAR EL MOTOR CON UNA BATERÍA BAJA (Vea Fig. 34) PARA REMOVER LAS RUEDAS (Vea Fig. 33) • • • Bloquee el eje en forma segura. Remueva la cubierta del eje, el anillo de retención y las arandelas para permitir la remoción de las ruedas (la rueda trasera contiene una llave cuadrada - no la pierda). Repare la llanta y vuélvala a montar. ADVERTENCIA: Las baterías de ácidoplo mo generan gases explosivos.
SERVICIO Y AJUSTES REEMPLAZAR LA BATERIA (Vea Fig. 35) ENTRECIERRE Y RELÉS El alambrado suelto o dañado puede producir el mal funcionamiento de su tractor, o que deje de funcionar, o le impida el arrancar. • Revise el alambrado. ADVERTENCIA: No haga cortocircuito con los terminales de la batería al permitir que una llave de tuerca o cualquier otro objeto entre en contacto con ambos terminales a la misma vez.
ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA CORRECCIÓN 3. 4. 5. 6. 7. Sin combustible. Motor sin la “ESTRANGULACIÓN” (CHOKE) adecuada. Motor ahogado. Bujía mala. Filtro de aire sucio. Filtro de combustible sucio. Agua en el combustible. 3. 4. 5. 6. 7. 8. 9. Alambrado suelto o dañado. Válvulas del motor desajustadas. 8. 9. 1. 2. 3. 4. 5. Filtro de aire sucio. Bujía mala. Batería baja o descargada. Filtro de combustible sucio. Combustible rancio o sucio. 1. 2. 3. 4. 5. 6. 7.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado 1. El corte disparejo 1. 2. 3. Mala descarga del césped 1. Revise el alambrado, los interruptores y la conexiones.Si no están correctas, pongase en contacto con un centro de servicio cualificado. PRECAUCIÓN: NO opere la máquina sino hasta haber corregido el problema. Cuchilla desgastada, doblada o suelta. El conjunto segador no estánivelado.
28 1. Plegar esta página a lo largo de la línea punteada arriba indicada. 2. Tener la página ante de sí mismos de modo que su borde izquierdo sea vertical paralelo al tronco del árbol u otra estructura vertical. 3. Mirar a través del pliegue en dirección de la pendiente que se quiere medir. 4. Comparar el ángulo del pliegue con la pendiente del terreno. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes.
AVISO 29
GARANTÍA LIMITADO El fabricante le garantiza al comprador consumidor original que este producto no tendrá defectos en los materiales ni en la mano de obra. Le repararemos o reemplazaremos, a nuestra opción, cualquier pieza que encontremos defectuosa a causa de los materiales o mano de obra, sin incluir los costos de las piezas o de mano de obra incurridos en el reemplazo de las piezas y durante un período de dos (2) años desde la fecha de compra del comprador consumidor original.