IMPORTANT OWNER'S MANUAL DO NOT THROW AWAY MANUAL WARNING: Read this Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. MODEL: PR17H42STF LAWN TRACTOR ALWAYS WEAR EYE PROTECTION DURING OPERATION 183041 3.6.02 TR Printed in U.S.A.
SAFETY RULES & s.FEoPE...o.P..C CESFO...OE N.OW .S IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • • • • • • • • • • • • • • • • • Avoid startingor stopping on a slope. Iftires lose traction, disengage the blades and proceed slowly straightdown the slope.
SAFETY RULES & • • • • Safe Operation Practices Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. Keep children out oftbe mowing area and under tbe watchful care of another responsible adult. Be alert and turn machine off if children enter the area. Before and when backing, look behind and down for small children.
PRODUCT SPECIFICATIONS GASOLINE CAPACITY AND TYPE: 2.0 GALLONS UNLEADED REGULAR OILTYPE (API-SF-SJ): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) OIL CAPACITY: W/FILTER: 3.5 PINTS W/OFILTER: 3.0 PINTS SPARK PLUG: 3AP: .030") CHAMPION RC12YC GROUND SPEED (MPH): Forward: Reverse CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
UNASSEMBLED Steering PARTS Seat Wheel © Steering Wheel Insert (1) Washer 17/32 x 1-3/16 x 12 Gauge Steering Extension Shaft (1) Knob _i_ Sleeve Slope Sheet Steering Steering Adapter (1) Large Flat Washer _L_-- _/ Locknut 1/2-20 Key (2) Keys (1) Locknut 1/4-28 (1) Oil Drain Tube (1) Hex Bolt 1/4-28 x 1-1/4 5
ASSEMBLY Your new tractor has been assembled at the factory with exception ofthose parts left unassembled forshipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY INSTALL SEAT (See Fig. 3) NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. Adjust seat before tightening adjustment knob. • Remove edjustment knoband flatwasher securing seat to cardboard packing and set aside for assembly of seat to tractor.
ASSEMBLY IMPORTANT: FOR SHIPISING PURPOSES, THE MULCHER PLATE WAS PREATTACHED TO YOUR MOWER. THE MULCHER PLATE MUST ONLY BE USED WITH THE MULCHING BLADES THAT CAME PACKED SEPARATELY IN THE CARTON. YOUR MOWER PERFORMANCE BLADES FOR YOUR MOWER THE MULCHER MOWER (SEE TO SET • CHECK MOWER FOR CHECK DECK LEVELNESS For best cutting results, mower housing should be propedy leveled. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor tofamiliarize yourself with the locations of various controls and adjustments. Save this manual for future reference. ATTACHMENT CLUTCH LEVER IGNITION SWITCH LIGHT SWITCH POSITION AMMETER LIFr LEVER PLUNGER THROTTLE/CHOKE CONTR( ATTACHMENT LIFT LEVER CLUTCH/ BRAKE PEDAL HEIGHT ADJUSTMENT KNOB PARKING BRAKE FREE WHEEL CONTRq CONTROL LEVER FIG.
OPERATION HOW TO USE YOUR TRACTOR IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD). TO SET PARKING BRAKE (See Fig. 6) Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. • Depress clutch/brake pedal into full "BRAKE" position and hold.
OPERATION TO OPERATE TO ADJUST GAUGE WHEELS (See Fig. 7) Gauge wheels are properly adjusted when they are slightly offthe groundwhen mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. [_ NOTE:Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in the Operation section of this manual).
OPERATION BEFORE STARTING THE ENGINE NOTE: Before starting, read the warm and cold starting procedures below. CHECK ENGINE oIL LEVEL • • • • • • The engine in you r tractor has been shipped, from the factory, already filled with summer weight oil. Check engine oilwith tractor on level ground. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until "FULL" mark on dipstick is reached.
OPERATION • Disengage transmission byplacing freewheel controlin freewheeling position (See "TO TRANSPORT" in this section of manual). • Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal. • Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds.
CUSTOMER MAINTENANCE F,L. ,.oA s RESPONSIBILITIES SCHEDULE _.,_.
CUSTOMER RESPONSIBILITIES TRACTOR TRAIUNG EDGE UP Always observe safety rules when performing any maintenance. BRAKE MANDREL ASSEMBLY BLADE CENTER HOLE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJ UST BRAKE" inthe Service and Adjustments section of this manual). LOCK WASHER TIRES • • • STAR Maintain prober air pressure inall tiros (See =PRODUCT SPECIFICATIONS" section of this manual).
CUSTOMER RESPONSIBILITIES NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt toopen or removecapsor covers. Adding or checking level of electrolyte is not necessary. NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.
CUSTOMER ENGINE COOLING RESPONSIBILITIES FINS IN-LINE Remove any dust, dirt or oil from engine cooling fins to preventengine damagefrom overheating.See enginemanual. FILTER (See Fig. 16) The fuel filter should be replaced once each season. Iffuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. • With engine cool, remove filter and plug fuel line sections. AIR FILTER Your engine will not runp ropedy usinga dirtyai rfilter.
SERVICE AND ADJUSTMENTS WARNING: TO AVIOD SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key to "STOP" and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER HOUSING • Adjust the mower while tractor is parked on level ground or ddveway. Make sure tires are prepedy inflated (See =PRODUCT SPECIFICATIONS" Section ofthis manual). Iftiresare over or underinflated, you will not properly adjust your mower, SIDE-TO-SIDE ADJUSTMENT (See Figs. 18 and 19) • Raise mower to its highest position. • At the midpoint of both sides of mower, measure height from bottom edge of mower to ground.
SERVICE AND ADJUSTMENTS TO ADJUST BRAKE (See Fig. 23) • Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle. • • Iftractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted. • Depress clutch/brake pedal and engage parking brake. • Measure distance petween brake operating arrnand nut "A" on brake rod.
SERVICE AND ADJUSTMENTS CONTROL If your battery is too weak to start the engine, it should be recharged. (See "BATFERY" in the CUSTOMER RESPONSIBILITIES section of this manual). ,NEUTRAL LOCK GATE If =jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES. ADJUSTMENT BOLT \ FIG.
SERVICE AND ADJUSTMENTS HEADLIGHT WIRE CONNECTOR FIG. 28 TERMINAL KEPS COVER _. _NUT FIG. 30 ENGINE BOLT TO ADJUST THROTTLE CONTROL CABLE POSITIVE CABLE (RED The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary. See engine manual. NEGATIVE (BLACK) CABLE TO ADJUST CARBURETOR FIG. 29 TO REPLACE • Raise hood.
STORAGE ENGINE Immediately prepare your tractorfor storage at the end ofthe season or ifthe tractor will not be used for 30 days or more, FUEL SYSTEM CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE.
TROUBLESHOOTING POINTS CAUSE PROBLEM Will not start 1. Out of fuel. 1. Fill fuel tank, 2. 3. 4. 5. 6. 7. Engine not =CHOKED" properly. Engine flo_led. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 2. 3, 4. 5. 6. 7. 8. 9, Loose or damaged wiring. Carburetor out of adjustment. 8. 9. See "TO START ENGINE" in Operafion section. Walt several minutes before attempfing to start. Replace spark plug. Clssn/replace air filter. Replace fuel filter.
TROUBLESHOOTING PROBLEM CAUSE Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-salety Poor cut - uneven 1. 2. Mower blades will not rotate Poor grass discharge Headlight(s) not working (if so equipped) Battery wlll not charge Loss of drive Engine "backfires" when taming engine "OFF" POINTS CORRECTION presence control system. 1. Check widng, switches and connections. If not corrected, contact an authorized service center/ department.
TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 SCHEMATIC RED BLACK BATrERY .Eo C_ FUSE RED STARTER BLACK I (oPTiOn) ;I WH_ _)G I ' t ' © ' O_,'-[ J CLUTCH / BRAKE (PEDAL UP) AI( I IGNITION SWITCH WHITE WHffEI....... BLACK I j;:o_ /; (NOT OCCUPIED) SEAT SWITCH , / A'R"MENTCLUTCH SLACK (CLUTCH OFF) _f : , I1_1 ....... _ 11 L I GROUNDING CONNECTOR METER HOUR }_ A (OPTIONAL) r I l .
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 ELECTRICAL 22 I i I I I I 43 i I I i I 41 I_.
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 ELECTRICAL KEY NO. PART NO. DESCRIPTION 1 2 8 16 21 22 24 25 26 27 28 29 30 33 40 41 42 43 45 52 90 163465 74760412 176689 176138 175685 4152_.
REPAIR PARTS TRACTOR CHASSIS - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 AND ENCLOSURES 29 12 26 25 i , 25 26 53 55 5 208 207 26 33 10 35 34 30 57 28
REPAIR PARTS TRACTOR CHASSIS - - MODEL NUMBER AND PR17H42STF, PRODUCT NUMBER 954 56 65-08 ENCLOSURES KEY NO. PART NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 DRIVE 32 30 62 36 32 I 30 32
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 DRIVE KEY NO. PART NO.
REPAIR PARTS TRACTOR STEERING / - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 ASSEMBLY • I t L ....
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 STEERING ASSEMBLY KEY NO. PART NO.
REPAIR PARTS TRACTOR SEAT - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 ASSEMBLY 7! ; 5 ; I I 21 I I 5 25 11 NO. 1 2 3 4 5 6 7 8 9 10 11 PART NO. 171683 14O551 71110616 19131610 145OO6 738OO6OO 124181X 17000616 19131614 182493 166369 DESCRIPTION KEY NO. Seat Bracket Pivot Seat 8 720 Bolt Fin Hex 318-16 Uric X 1 Washer 13/32 X 1 X 10 Ga Clip Push-In Nut Hex w!lns. 3/8-16 U nc Spring Seat Cprsn 2 250 BIk Zi Screw 3/8-16 X 1.5 Washer 13/32 X 1 X 14 Ga.
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 DECALS 2 11 16 2 2O 9 18 14 KEY NO. PART NO. DESCRIPTION KEY NO. PART NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 6508 ENGINE 3 81 4 14 31 112 29 \ OPTIONAL EQUIPMENT Spark Arrester 38
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-.08 ENGINE KEY NO. PART NO.
REPAIR PARTS TRACTOR MOWER - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 DECK 103 105 ,146 101 102/ >21 21 27 4O
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 MOWER DECK KEY NO. PART NO.
REPAIR PARTS TRACTOR MOWER - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 LIFT 28 27 25 24 23 7 41 49 3O 1/50 3 6 5 4 13 19 13 13_---_ 31_ , 20 I L 19 32 42 15 .
REPAIR PARTS TRACTOR - - MODEL NUMBER PR17H42STF, PRODUCT NUMBER 954 56 65-08 MOWER LIFT KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 11 12 13 15 16 17 18 19 20 23 24 25 26 27 28 20 30 31 32 36 37 38 40 41 49 50 159460 159471 105767X 12O00002 19211621 120183)( 125631X 170770 13.
NOTES 44
NOTES 45
LIMITED WARRANTY The Manufacturer warrants tothe originalconsumer purchaserthat this productas manufacturedis free from defects in materialsand workmanship.For a period of two (2) years from date of purchase by the originalconsumerpurchaser,we will repair or replace, at our option, withoutcharge for pads or labor incurredin replacingparts, any part which we find to be defectivedue to materials or workmanship.This Warrantyis subjectto the following limitationsand exclusions. 1.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES _k MAX. down the face of slopes, never across the face. Do not mow ARNING: To avoid serious injury, operate your tractor and slopes greater than 15 degrees. Make turns gradually to up prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
PARTS AND SERVICE Your POULAN PRO product has been quality standards. As with all mechanical necessary during the life of your unit. FOR SERVICE your OR REPLACEMENT L Consult 2. Consult the yellow (under "saws" for Blowers). 3. For replacement a. Model b. Description NOTE: dealer/place to rigid may be PARTS: of purchase.
