ine r. nta t co em lac nd ly a cke d or da ge ma rec om ed en rep me e on d. Us cra en ce wh pla tly. qu g fre Re en ba eck rat . Ch ion tierio ar t to jec rlyiss an d de we ub r. ine nta pe r is nta pro ine s co les r un INGmowe RNerate WAnot op ly a om rec ed nd me rep lac en em t co e on d. Us Do ma cra cke d or ge da en ce pla tly. .
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers • IV. TOWING • • • • • Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes. Never allow children or others in or on towed equipment. On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Travel slowly and allow extra distance to stop.
Know Your Grass Catcher READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference.
ASSEMBLY 1 2 BAGGER SUPPORT ASSEMBLY (See Fig. 1A) 1. Your tractor already has four (4) shoulder bolts installed on the rear drawbar, simply hang the support assembly on the bolts. NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor as shown. 2. Lift and rotate cover to align cover bracket with support assembly. 3. Slide cover assembly down onto the support assembly.
3 4 CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side first with warning to outside of unit. Install other container to right side. NOTE: Right container should always overlap left container at center support. 2.
5 6 ATTACH LOWER CHUTE (See Fig. 5) 1. Raise and hold deflector shield in upright position. 2. Place slot in lower chute over tab on mower deck and position lower chute over deck opening as shown. 3. Hook rear latch into flange hole on back of mower deck. 4. Hook front latch into tab hole on front of mower deck. UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower deck to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover.
OPERATION • Avoid cutting wet grass or in the morning while the dew is still heavy. Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging. • Your bagger is equipped with a full bagger indicator. Movement of the wheel increases as the bags fill. The wheel will be spinning fastest just before the bags fill completely. When the wheel stops, it indicates that the bags are full and the chutes have become clogged.
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS STORAGE Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. CAUTION: Do not leave grass in bagger containers. Empty containers after each use and before storing.
REPAIR PARTS / PIÈCES DE RECHANGE GRASS CATCHER - NUMBER QCT38-97 (96072000100) RAMASSE-HERBE - NUMÉRO QCT38-97 (96072000100) 3 2 4 5 6 7 20 2 8 20 10 9 38 11 39 20 9 12 13 20 10 2 14 18 20 2 2 15 20 35 15 21 2 W RA D INo tonbous p ej GtN are t tc arc e o kc om aew de rew na r ad ro lnu d se ted gam c s rei .de no roi iat ita esU ren C .no ylno si rp kceh er a po oc lre ab siy rf g emm ts n q e d n lla ltneu r de e d e .y lp C. no eR ca iat alp me ren ec ne si ehw noc t n iat n .
REPAIR PARTS / PIÈCES DE RECHANGE GRASS CATCHER - NUMBER QCT38-97 (96072000100) RAMASSE-HERBE - NUMÉRO QCT38-97 (96072000100) PART NO. DESCRIPTION 2 3 4 532069180 532127533 532171061 Nut, Crownlock #10-24 Screen, Cover Cover Asm.(Incl. 3,38,39) 5 6 7 532126840 818021008 532130933 Chute, Upper Screw, Special Full Bag Indicator 8 9 10 11 12 13 14 15 18 20 532087175 819061216 532007206 532060867 810071000 532109808 532125004 532160793 532192574 871081010 Screw, #10-24 x 1-1/8 Washer 3/16x3/4x16 Ga.