Manual

• Release the throttle trigger as soon as
the cut is completed, allowthg the en-
gine to idle. If you run the saw at full
throttle without a cutting load, unneces-
sary wear can occur to the chain, bar
and engine.
• To avoid losing controlwhen cut is com-
plete, do not put pressure on saw at end
of cut.
• Stop the engine before setting the saw down.
TREE FELLING TECHNIQUES
_kWARNING: Checkforbrokenordead
branches which can fail while cutting causing
serious injury. Do not cut near buildings or
electrical wires ifyou do not know the direction
of tree fall, at night since you will not be able to
see well, or during bad weather such as rain,
snow, or strong winds, etc. If tree makes con-
tact with any utility line, the utility company
should be notified immediately.
• Carefully plan your sawing operation in ad-
vance.
• Cleartheworkarea. You needac]eararea
all around the tree so you can have secure
footing.
• The chain saw operator should keep on
the uphill side of the terrain as the tree is
likely to roll or slide downhill after it is felled.
• Study the natural conditions that can cause
the tree to fall in a padicu]ar direction.
Natural conditions that can cause a tree to
fa]l Jn a particular direction include:
• The wind direction and speed.
• The ]ean of the tree. The lean of a tree
might not be apparent due to uneven or
sloping terrain. Use a plumb or leve] to de-
termine the direction of tree lean.
• Weight and branches on one side.
• Surrounding trees and obstacles.
Look for decay and rot. If the trunk is rotted, it
can snap and fail toward the operator.
Make sure there is enough room for the tree to
fall. Maintain a distance of 2-1/2 tree lengths
from the nearest person or other objects. En-
gine nc4se can drown out a warning call.
Remove dirt, stones, loose bark, nails, staples,
and wire from the tree where cuts are to be
made.
Plan a clear retreat path to the rear and diago-
nal to the line of fall.
Plan a clear retreat path
:t ÷- "£_" _ - Direction of Fall
FELLING LARGE TREES
(6 inches in diameter or larger)
The notch method is used to fell large trees.
A notch is cut on the side of the tree in the de-
sired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.
NOTE: If the tree has large buttress roots,
remove them before making the notch. If us-
ing saw to remove buttress roots, keep saw
chain from contacting ground to prevent dull-
ing of the chain.
NOTCH CUT AND FELLING THE
TREE
• Make notch cut by cutting the top of the
notch first. Cut through 1/3 of the diameter
ofthetree. Next complete the notch bycut-
ting the bottom of the notch. See illustra-
tion. Once the notch is cut remove the
notch of wood from the tree.
Final cut here 2 inches
above center of notch.
First cut _ ,2'I
Notch_h - ..... =
Second out
• After removing the wood from the notch,
make the felling cut on the opposite side of
the notch. This is done by making a cut
about two inches higher than the center of
the notch. This will leave enough uncut
wood between the fell] ng cut and the notch
toform a hinge. This hinge will help prevent
the tree from falling in the wrong direction.
Hinge holds tree on stump and helps
control fall
_\ \_'_ Opening
of felling
cut
Closing of_/_,J_ 1_
notch
NOTE: Before felling cut is complete, use
wedges to open the cut if necessary to
controt the direction of fall To avoid kickback
and chain damage, use wood or plastic
wedges, but never steel or iron wedges.
• Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell-
ing cut, or movement in the upper
branches.
• As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
• DO NOT cut down a partially fallen tree
with your saw. Be extremely cautious with
partially fallen trees that may be poorly
supported. When a tree doesn't fall com-
pletely, set the saw aside and pull down the
tree with a cable winch, block and tackle,
or tractor.
11