ENGLISH R Instruction Manual Manual de Instrucciones Manuel d’Instructions PP3516 / PP4018 ESPAÑOL For Occasional Use Only WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e enstrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.
IDENTIFICATION OF SYMBOLS WARNING! This chain saw can be dangerous! Careless or improper use can cause serious or even fatal injury. Read and understand the instruction manual before using the chain saw. Always wear appropriate ear protection, eye protection and head protection. Always use two hands when operating the chain saw.
gloves; eye protection such as non-fogging, vented goggles or face screen; an approved safety hard hat; and sound barriers (ear plugs or mufflers) to protect your hearing. Regular users should have hearing checked regularly as chain saw noise can damage hearing. Secure hair above shoulder length.
S Begin and continue cutting at full speed. If the chain is moving at a slower speed, there is greater chance of kickback occurring. S Cut one log at a time. S Use extreme caution when re-entering a previous cut. S Do not attempt cuts starting with the tip of the bar (plunge cuts). S Watch for shifting logs or other forces that could close a cut and pinch or fall into chain. S Use the Reduced--Kickback Guide Bar and Low--Kickback Chain specified for your saw.
KICKBACK SAFETY FEATURES WARNING: WE DO NOT REPRESENT AND YOU SHOULD NOT ASSUME THAT THE CHAIN BRAKE WILL PROTECT YOU IN THE EVENT OF A KICKBACK. Kickback is a lightning fast action which throws the bar and rotating chain back and up toward the operator. Kickback can be caused by allowing contact of the bar tip in the danger zone with any hard object. Kickback can also be caused by pinching the saw chain along the top of the guide bar. This action may push the guide bar rapidly back toward the operator.
Computed kickback angle (CKA) Table BAR CKA without chain brake MODEL P/N Length CHAIN P/N PP3516 952044942 16″ 952051547 33_ PP4018 952044926 18″ 952051548 33_ NOTE: If this saw is to be used for com- 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines to be equipped with a spark arresting screen.
4. Slide guide bar on bar bolts until guide bar stops against clutch drum sprocket. Guide Bar Bar Nuts Bar bolts Guide bar 5. Adjusting the tension: Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw. An adjusting screw (located on the guide bar) is used to adjust the tension of the chain (see illustration). 1.
OPERATION KNOW YOUR CHAIN SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
BEFORE STARTING ENGINE Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for additional information. WARNING: Be sure to read the fuel handling information in the safety rules section of this manual before you begin.
IGNITION SWITCH ON STOP Choke Lever 1. Move ON/STOP switch to the ON position. 2. Slowly press primer bulb 6 times. 3. Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position). 4. Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step. NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step. 5. Push the choke/fast idle lever in to the HALF CHOKE position.
OPERATING TIPS S Check chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section. S Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc. S Stop the saw if the chain strikes a foreign object. Inspect the saw and repair or replace parts as necessary. S Keep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.
Hinge holds tree on stump and helps control fall Opening of felling cut Closing of notch Use a wedge to remove pinched saw Turn saw OFF and use a plastic or wooden wedge to force cut open. Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pressure. Overcutting NOTE: Before felling cut is complete, use wedges to open the cut if necessary to control the direction of fall.
Using a log for support 2nd Cut 1st Cut 1st Cut S Watch out for springpoles. Springpoles are small size limbs which can catch the saw chain and whip toward you or pull you off balance. Use extreme caution when cutting small size limbs or slender material. S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released. S Keep a clear work area.
SERVICE WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an authorized or Master Service Dealer. HELPFUL TIP IMPORTANT: Have all repairs other than the recommended maintenance described in the instruction manual performed by an authorized service dealer. If any dealer other than an authorized service dealer performs work on the product, Electrolux Home Products, Inc.
Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when excess heating or burring of the rails occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw. Cylinder Cover Air Filter Cover Air Filter CHECK FUEL MIXTURE LEVEL S See FUELING ENGINE under the OPERATION section.
REPLACE SPARK PLUG The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and nonadjustable. 1. Loosen 3 screws on cylinder cover. 2. Remove the cylinder cover. 3. Pull off the spark plug boot. 4. Remove spark plug from cylinder and discard. 5. Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm). 6. Reinstall the spark plug boot. 7.
HELPFUL TIP During storage of your gas/ oil mixture, the oil will separate from the gas. We recommend that you shake the gas can weekly to insure proper blending of the gas and oil. ENGINE S Remove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. S Replace spark plug with new one of recommended type and heat range. S Clean air filter. S Check entire unit for loose screws, nuts, and bolts.
LIMITED WARRANTY ELECTROLUX HOME PRODUCTS, INC., warrants to the original purchaser that each new Poulan PROR brand gasoline chain saw is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline chain saw as follows from the original date of purchase. 2 YEARS - Parts and Labor, when used for Household purposes. 60 DAYS - Parts and Labor, when used for Commercial, Professional, or Income Producing purposes.
WARRANTY COMMENCEMENT DATE: The warranty period begins on the date the small off--road engine is purchased. LENGTH OF COVERAGE: This warranty shall be for a period of two years from the initial date of purchase. WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replacement of any warranted part will be performed at no charge to the owner at an approved ELECTROLUX HOME PRODUCTS, INC., servicing center.