030 21 OWNER’S MANUAL Model GTT354 Mfg. ID No. 96072001000 Product No. 960 72 00-10 54 Inch Mower Grass Catcher • • • • Assembly Operation Customer Responsibilities Repair Parts 532402349 11.17.05 rad Printed in U.S.A.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IV. TOWING • • • • • • Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes. Never allow children or others in or on towed equipment. On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Travel slowly and allow extra distance to stop.
KNOW YOUR GRASS CATCHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference.
ASSEMBLY 1 1. Slide flanges of support assembly into drawbar slots first, then, pivot backwards inserting pin into drawbar pin hole. 2. Be sure support assembly is seated properly, then secure with retainer spring. INSTALL HIGH LIFT BAGGING BLADES (See Fig. 1) CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. SUPPORT ASSEMBLY NOTE: If you already have high lift bagging blades on your mower, store the supplied blades in a safe place for future use.
4 5 CONTAINER ASSEMBLY (See Fig. 4) CONTAINER MOUNTING (See Fig. 5) 1. Install one container to left side first with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right container should always overlap left container at center supports. 2. Close cover and lock latch handles over center support tubes. 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3.
6 7 LOWER CHUTE (See Fig. 6) 1. Raise and hold deflector shield in upright position. 2. Place slot in lower chute over tab on mower and position lower chute over mower opening as shown. 3. Hook rear latch into flange hole on back of mower. 4. Hook front latch into hole in front gauge wheel bracket or under gauge wheel bracket on mower without a hole in bracket. UPPER CHUTE (See Figs. 7A & 7B) 1. Lower mower to its lowest cutting position. 2.
OPERATION • Avoid cutting wet grass or in the morning while the dew is still heavy. Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging. • Your bagger is equipped with a full bagger indicator. Movement of the wheel increases as the bags fill. The wheel will be spinning fastest just before the bags fill completely. When the wheel stops, it indicates that the bags are full and the chutes have become clogged.
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS STORAGE Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. CAUTION: Do not leave grass in bagger containers. Empty containers after each use and before storing.
REPAIR PARTS GRASS CATCHER - MODEL GTT354 (MFG. ID 96072001000) / RAMASSE-HERBE - MODÈLE GTT354 (MFG ID 96072001000) PRODUCT NUMBER 960 72 00-10 / NO. DE PRODUIT 960 72 00-10 4 5 6 7 8 10 2 9 12 13 9 14 2 18 38 20 15 16 38 20 34 10 20 20 15 9 12 37 3 14 16 W RoAn oDs IN t u po ejb c GetN are ot tc kcar e w om rae ro d rew na ad lnu d d am se ite eg c s ire .d no ro sU iat oita o e ren .n ln si hC a y rp kceocer po lre gab m siy erf nem tsn uq ed lla yltne er d e p d C. R .
REPAIR PARTS GRASS CATCHER - MODEL GTT354 (MFG. ID 96072001000) / RAMASSE-HERBE - MODÈLE GTT354 (MFG ID 96072001000) PRODUCT NUMBER 960 72 00-10 / NO. DE PRODUIT 960 72 00-10 KEY NO. 2 3 4 11 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. DESCRIPTION 532069180 Nut, Crownlock #10-24 532192709 Screen, Cover 532195373 Cover Assembly (Includes 34, 37) 532187299 Chute, Upper 818021008 Screw, Special #10-14x1/2 532130933 Full Bag Indicator 532087175 Screw, #10-24 x 1-1/8 819061216 Washer 3/16x3/4x16 Ga.